2017 Nissan-Datsun Altima Technical Service Bulletin # NHTSA10V401000 Date: 100903

2017 Nissan-Datsun Altima Technical Service Bulletin # NHTSA10V401000 Date: 100903

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 464

Recall 10V401000: Potential GPS Battery Fires

VEHICLE MAKE/MODEL: MODEL YEAR(S):

Nissan/Altima 2008-2010

Nissan/Frontier 2008-2010

Nissan/Pathfinder 2008-2010

Nissan/Rogue 2008-2010

Nissan/Sentra 2008-2010

Nissan/Versa 2008-2010

Nissan/XTerra 2008-2010

MANUFACTURER: Nissan North America, Inc.

MFR'S REPORT DATE: September 03, 2010

NHTSA CAMPAIGN ID NUMBER: 10V401000

NHTSA ACTION NUMBER: N/A

COMPONENT: Equipment: Electrical: Navigational System (Global Positioning System)

POTENTIAL NUMBER OF UNITS AFFECTED: ?

SUMMARY:

Nissan is recalling certain vehicles that were equipped with a Garmin Nuvi Model 750 navigation system. The batteries contained in the affected

GPS units can overheat.

CONSEQUENCE:

Overheated batteries could result in a fire.

REMEDY:

Nissan will notify owners and the repairs will be performed by Garmin technicians by replacing the battery and inserting a spacer on top of the

battery free of charge. The safety recall is expected to begin during September 2010. Owners may contact Garmin directly at 1-866-957-1981 or

Nissan at 1-800-647-7261.

NOTES:

Owners may also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153),

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-049B Date: 111110

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-049B Date: 111110

Engine Controls - Idle Fluctuation When Engine Is Cold

Classification: EC11-015B

Reference: NTB11-049B

Date: November 10, 2011

2010-2012 ALTIMA SEDAN AND COUPE;

IDLE FLUCTUATION WHEN ENGINE IS COLD

This bulletin has been amended. APPLIED VEHICLES, the description under IF YOU CONFIRM, and Table A have been revised. Please discard

all previous copies.

APPLIED VEHICLES:2010-2012 Altima Sedan and Coupe (L32 and CL32)

APPLIED ENGINE: QR25DE (4 cylinder engine)

with California Emissions ONLY

IF YOU CONFIRM

The idle speed fluctuates from approximately 1,000 to 2,000 RPM during ALL of the following conditions:

^ Occurs for no more than one minute after the engine is started

^ ONLY when the engine is cold

^ ONLY when the transmission is in Park or Neutral

AND

The idle speed is normal (stable) when the engine warms to normal operating temperature.

NOTE:

This incident, if it should occur, may occur immediately after an oil change.

ACTION

1. Refer to step 2 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on.

2. If this bulletin applies, reprogram the ECM.

IMPORTANT:

The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 481

CLAIMS INFORMATION

SERVICE PROCEDURE

1. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

^ If you are not familiar with the reprogramming procedure, refer to the "CONSULT- III (C-III) ECM Reprogramming" general procedure.

CAUTION

2. When you get to the ECM Reprogramming screen shown in Figure 1, confirm this bulletin applies as follows.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 482

A. On your C-III screen, look at the Part Number column (see Figure 1):

^ If this column is blank (no part number listed), this bulletin does not apply. Close C-III and refer to ASIST for further diagnostic information.

^ If a Part Number is listed, write it on the Repair Order.

B. Compare the Part Number you wrote down to the numbers in the Current ECM Part Number column in Table A.

^ If there is a match, this bulletin applies. Continue with the reprogramming procedure.

NOTE:

If there are two lines (two reprogramming options) on your C-III screen, use the one that does not have the message "Caution! Use ONLY with

NTBXX-XXX".

^ If there is not a match, this bulletin does not apply. Close C-III and refer to ASIST for further diagnostic information.

3. If this bulletin applies and you have performed ECM reprogramming, the screen in Figure 2 will display when reprogramming is complete.

NOTE:

If the screen in Figure 2 does not display (reprogramming does not complete). Refer to the "ECM Reprogram Interruption Recovery general

procedure".

^ Print this screen and attach it to the Repair Order for Warranty documentation.

4. Make sure to erase DTCs from all systems.

NOTE:

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 483

During reprogramming, DTCs will set in several systems and must be erased.

5. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.

^ If the MIL comes ON, go back to ASIST for further diagnostic information.

^ Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.

2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221

2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221

Lighting - Exterior Lamp Fogging

Classification: EL03-030F

Reference: NTB03-074F

Date: February 21, 2012

EXTERIOR LAMP FOGGING

This bulletin has been amended. The Applied Vehicles section and the first paragraph of the Service Information section have been revised. Please

discard all previous versions.

APPLIED VEHICLES: 2001-2012 Nissan, All Models

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 158

SERVICE INFORMATION

Occasionally customers may notice water vapor or fog in the exterior lamps. This is generally NOT due to a defect.

The following information, illustrations, and flow chart are provided to help you in determining if an incident for water/condensation in the lamps is

normal or not.

All current exterior lamp assemblies are vented to the atmosphere (not sealed).

^ This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the lamp.

^ Moisture in the air sometimes "travels" into and out of the lamp assembly through these vents.

^ Certain environmental conditions may cause moisture to condense.

^ The fogging/cloudiness should disappear over time when the lamp is in a dry environment.

Fog may temporarily form inside the lens of the exterior lamp assemblies based on environmental conditions or sudden temperature changes (such as

in a car wash, or parked on a cold, sunny day). This is normal. See Figure 1.

NOTE:

This condensation can appear anywhere on the outer lens, typically at its coldest location.

If the moisture trickles, drips, or pools, it may not be considered normal and the lamp assembly may have a water leak path. See Figure 2 for an

example.

If large drops of water collect inside the lens, refer to the flow chart below to find the next step.

SERVICE PROCEDURE

Should a customer note water in a lamp assembly, please use the following flow chart to determine if the condition is normal or requires lamp

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 159

2014 Nissan-Datsun Altima Diagrams. DTC # 10-038 Date: 100311

2014 Nissan-Datsun Altima Diagrams. DTC # 10-038 Date: 100311

Electrical - JIS & CCA Battery Testing Information

Classification: EL10-010

Reference: NTB10-038

Date: March 11, 2010

NISSAN; TESTING JIS-TYPE & CCA-TYPE BATTERIES

APPLIED VEHICLES: All Nissan vehicles

SERVICE INFORMATION

Nissan vehicles equipped with standard lead/acid batteries use one of two different types with unique battery rating specifications: JIS & CCA.

JIS = Japan Industrial Standard, used for Japan produced batteries

CCA = Cold Cranking Amps, standard for North American produced batteries

IMPORTANT:

^ JIS batteries have different testing specifications than CCA batteries.

^ If you must use the GR8 Battery Tester in a mode other than MODEL mode, JIS Mode MUST ALWAYS BE USED for JIS batteries otherwise an

incorrect result will occur. NEVER test a JIS battery using the CCA test in the GR8; the test software in the GR8 is different for JIS and CCA

modes. ANY CCA value you may have for a JIS-type battery is inaccurate for testing purposes.

ALWAYS test with the GR8 using the MODEL mode (if available).

^ Selecting MODEL and vehicle type will automatically select the proper JIS or CCA value for the Original Equipment battery.

^ If the applicable vehicle is not listed update the GR8 to make sure it has the most recent data package.

^ If the applicable vehicle still is not listed:

1) Determine which type of battery (CCA or JIS) is installed in the vehicle. See below for descriptions of each battery.

2) Select CCA or JIS in the GR8 based on the type of battery installed. See below for more information.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 224

Determine the Battery Type

Batteries with JIS (Japanese Industrial Standard) Number

^ Batteries installed in vehicles produced in Japan have a JIS number embossed in the plastic on top of the battery.

^ These vehicles have a VIN that begins with the letter "J".

Batteries with CCA (Cold Cranking Amps) Number

^ Batteries installed in vehicles produced in North America have a CCA number displayed on the label attached to the top of the battery.

^ These vehicles have a VIN that begins with a number: 1, 3, or 5.

Selecting CCA or JIS in the GR8 Battery Tester

Vehicles with JIS Battery

^ Select JIS, then choose the option that matches the first five (5) characters of the JIS number on the battery.

NOTE:

DO NOT select CCA when testing a JIS battery.

Vehicles with CCA Battery

^ Select CCA, then choose the option that matches the number following "Cold Cranking Amps" on the battery.

Reference Material

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 225

The information shown above can be printed and attached to the GR8, if needed.

Disclaimer2014 Nissan-Datsun Altima Diagrams. DTC # 11-012B Date: 130215

2019 Nissan-Datsun Altima Diagnostic and Repair Information # NHTSA10V401000 Date: 100903

2019 Nissan-Datsun Altima Diagnostic and Repair Information # NHTSA10V401000 Date: 100903

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 464

Recall 10V401000: Potential GPS Battery Fires

VEHICLE MAKE/MODEL: MODEL YEAR(S):

Nissan/Altima 2008-2010

Nissan/Frontier 2008-2010

Nissan/Pathfinder 2008-2010

Nissan/Rogue 2008-2010

Nissan/Sentra 2008-2010

Nissan/Versa 2008-2010

Nissan/XTerra 2008-2010

MANUFACTURER: Nissan North America, Inc.

MFR'S REPORT DATE: September 03, 2010

NHTSA CAMPAIGN ID NUMBER: 10V401000

NHTSA ACTION NUMBER: N/A

COMPONENT: Equipment: Electrical: Navigational System (Global Positioning System)

POTENTIAL NUMBER OF UNITS AFFECTED: ?

SUMMARY:

Nissan is recalling certain vehicles that were equipped with a Garmin Nuvi Model 750 navigation system. The batteries contained in the affected

GPS units can overheat.

CONSEQUENCE:

Overheated batteries could result in a fire.

REMEDY:

Nissan will notify owners and the repairs will be performed by Garmin technicians by replacing the battery and inserting a spacer on top of the

battery free of charge. The safety recall is expected to begin during September 2010. Owners may contact Garmin directly at 1-866-957-1981 or

Nissan at 1-800-647-7261.

NOTES:

Owners may also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153),

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-033B Date: 120314

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-033B Date: 120314

Multi AV System - Configuration After Replacing Control Unit

Classification: EL10-008B

Reference: NTB10-033B

Date: March 14, 2012

AV CONTROL UNIT REPLACEMENT REQUIRES CONSULT-III PLUS CONFIGURATION

This bulletin has been amended. The Applied Vehicles and Service Procedure sections have been revised. Please discard previous versions.

APPLIED VEHICLES:2010-2012 370Z Coupe and Roadster (H/Z34)

2010-2012 Altima Coupe, Sedan, and Hybrid (C/L32/HV)

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 130

2011-2013 GT-R (R35)

2010-2012 Maxima (A35)

2011-2012 Murano and Murano Cross Cabriolet (E/Z51)

2011-2012 Quest (E52)

SERVICE INFORMATION

If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason follow the steps in the Service Procedure to configure the Multi

AV system.

NOTE:

The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control

Unit until instructed.

Service Procedure

Before starting, make sure your ASIST has been freshly synchronized and all CONSULT-III (C-III) plus upgrades have been installed.

Parts of the Procedure

PART 1:

Record Multi AV Configuration Values of Original AV Control Unit; Replace AV Control Unit

1. Make sure the shift selector is in Park, and the parking brake is set.

2. Connect the C-III plus VI to the vehicle.

3. Turn ON the ignition.

NOTE:

You may want to start the engine to keep the battery charged during this procedure.

4. Write down customers radio station presets. (Presets will be lost during this procedure.)

5. Launch CONSULT-III (C-III) plus on the CONSULT PC.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 131

6. Select Re/programming Configuration.

7. Read the General Precaution.

When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.

8. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.

9. Select, Select.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 132

10. Confirm the correct Model Name and Model Year are displayed.

When finished, select Confirm.

11. After system call completes, confirm the correct VIN is displayed.

When finished, select Confirm.

NOTE:

If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.

12. Select MULTI AV.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 133

13. Select Read/Write Configuration.

14. Select Before Replace ECU.

15. Confirm current configuration and write it down.

^ Configuration can also be printed with the Print Screen button or Screen Capture button.

NOTE:

Configurable options will differ between models. Your screen may look different.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 134

16. Select Save.

NOTE:

If the configuration data cannot be saved, replace the AV Control Unit as instructed in the applicable Electronic Service Manual (ESM) and then

proceed to PART 3: Perform Multi AV Initialization shown below in this bulletin.

17. Select End.

18. Replace the AV Control Unit as instructed in the applicable ESM.

PART 2:

Configure the Multi AV System

19. Perform steps 1-10.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 135

20. Select Confirm.

21. Select After Replace ECU.

22. Select OK.

After performing step 22

If an error message does not display:

^ Proceed to PART 5: Confirm Multi AV System Is Operational shown below in this bulletin.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 136

If an error message does display:

^ Proceed to PART 3: Perform Multi AV Initialization, below.

PART 3 (if needed):

Perform Multi AV Initialization

NOTE:

Leave C-III plus running and the VI connected while performing Multi-AV initialization.

23. Turn OFF the audio system.

24. Put the AV system into System Diagnostic Mode as follows:

a. Press and hold the SETTING button (see Figure 14).

b. While holding the SETTING button, turn the volume control knob 40 clicks or more.

^ The volume control knob can be turned either direction.

^ When the system goes into the System Diagnostic Menu, the screen in Figure 15 will display.

25. Select Confirmation/Adjustment.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 137

26. Select Delete Unit Connection Log.

27. Select Yes.

28. Select Initialize Settings.

29. Select Accessory Number Initialization.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 138

30. Select Yes.

31. Wait while the system initializes.

^ The screen in Figure 21 will display while initializing.

^ The screen in Figure 22 will display when initialization is complete.

32. Once initialization is complete, reboot the Multi AV system as follows:

a. Turn OFF the ignition.

b. Wait 10 seconds.

c. Turn ON the ignition.

Proceed to PART 4: Manually Configure the Multi AV System, below.

PART 4 (if needed):

Manually Configure the Multi AV System

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 139

NOTE:

If the screen in Figure 23 is not displayed, click on the Home icon.

33. Select Re/programming Configuration.

34. Read the General Precaution.

When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.

35. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 140

36. Select, Select.

37. Confirm the correct Model Name and Model Year are displayed.

When finished, select Confirm.

38. Confirm the correct VIN is displayed.

When finished, select Confirm.

NOTE:

If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 141

39. Select MULTI AV.

40. Select Manual Configuration.

41. Use the drop down menus to select the Configuration options that were printed or written down in step 15.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 142

^ Configurable options will differ between models. Your screen may look different from Figures 30 and 31.

42. Select Next.

43. Confirm the configuration displayed is correct, then select OK.

44. Start the engine and let it idle briefly.

45. Use C-III plus to clear any codes from the Multi AV system.

a. Select Diagnoses (One System)> Multi AV> Self Diagnosis Results.

b. Clear any codes that may be present.

46. Close C-III plus and disconnect the VI from the vehicle.

PART 5:

Confirm Multi AV System Is Operational

47. Put your toot on the brake, start the engine, and move the shift selector to R (reverse).

48. If equipped, make sure the rear view monitor is working correctly.

49. Put the shift selector back into Park.

50. Turn ON the radio.

51. Turn the volume knob and make sure the audio volume responds to movement of the knob.

2014 Nissan-Datsun Altima Diagrams. DTC # 10-075 Date: 100608

2014 Nissan-Datsun Altima Diagrams. DTC # 10-075 Date: 100608

Body - Front/Rear Door Weatherstrip Loose/Pulled Out

Classification: BT10-012

Reference: NTB10-075

Date: June 8, 2010

2007-2010 ALTIMA; DOOR WEATHERSTRIP LOOSE

APPLIED VEHICLES:

2007 - 2010 Altima Sedan (L32)

2008 - 2010 Altima Coupe (CL32)

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 425

2007 - 2010 Altima Hybrid (L32HV)

IF YOU CONFIRM:

The front or rear door weatherstrip has pulled out, or is loose (see Figure 1).

ACTION:

Re-install the weatherstrip using the SERVICE PROCEDURE of this bulletin.

^ Apply this repair to the incident door weatherstrip only.

NOTE:

Do NOT replace any door weatherstrip for this incident, if it should occur.

IMPORTANT:

The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 426

1. Remove the door weatherstrip from the sash channel area of the upper door frame. Figure 3 shows a cutaway of the weatherstrip.

a. Carefully peel up the weatherstrip's "lower" ridge from its channel (see Figure 3).

b. Complete upper weatherstrip removal by pulling its "upper" ridge from its channel (see Figure 3).

2. Clean out the sash channel and the bottom of the weatherstrip.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 427

^ Use a clean shop towel and isopropyl alcohol or equivalent cleaner (see Figure 4 and 5).

3. Apply two (2) beads of Nissan Weatherstrip Cement (cement) along the whole upper channel as shown in Figure 6.

NOTE:

Use Nissan Weatherstrip Cement only. See (PARTS INFORMATION).

^ Bead width: approximately 3/32 inch (2.5 mm).

^ Apply the beads the length of the channel, and 1/2 inch (13 mm) from each end.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 428

4. Re-install the weatherstrip immediately after cement application as follows:

a. Press in the weatherstrip upper ridge into the upper channel.

b. While maintaining upward tension to keep it in the upper channel, press the weatherstrip's lower ridge into its channel.

^ If necessary, use a plastic "finesse stick" or similar trim tool to push the lower ridge over and into its channel (see Figure 7).

c. Using the plastic "finesse stick" or similar trim tool, push on the mid-section area to fully seat the weatherstrip (see Figure 8).

^ Run your finger down this area to feel for any high spots. High spots will indicate where the weatherstrip ridge is not fully seated.

^ Re-seat as needed.

5. Inspect proper weatherstrip installation by carefully lifting up on the weatherstrip slightly.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 429

^ Figure 9 shows an OK condition.

^ Figure 10 shows a No Good condition.

> To correct this condition, refer back and perform Step 4b and 4c as needed.

6. Clean off any excess cement with a suitable cleaner.

7. Let the cement dry for at least 15 minutes, and then re-check for proper adhesion.

2014 Nissan-Datsun Altima Diagrams. DTC # 10-068E Date: 130128

2014 Nissan-Datsun Altima Diagrams. DTC # 10-068E Date: 130128

Campaign P0337 - Navigation Software Update For Various Issues

Reference:

NTB10-068e

Date:

January 28, 2013

VOLUNTARY SERVICE CAMPAIGN

NISSAN NAVIGATION SOFTWARE UPDATE

This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions

of this bulletin.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 506

CAMPAIGN ID #: P0337

APPLIED VEHICLES:

2010 Altima Sedan, Coupe, and Hybrid (L32, CL32, and L32HV)

2010 Maxima (A35)

2010 370Z Coupe and Roadster (Z34 and HZ34)

2011 GT-R (R35)

Check Service Comm to confirm campaign eligibility.

INTRODUCTION

On the Applied Vehicles listed above, the navigation, mobile phone, and iPod(R) functions may not be working as intended. To remedy this

potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor.

IDENTIFICATION NUMBER

Nissan has assigned identification number P0337 to this campaign. This number must appear on all communications and documentation of any

nature dealing with this campaign.

DEALER RESPONSIBILITY

Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private

parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.

REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE

^ Discs 1/3 and 2/3 of the set shown in Figure A are used for all applied models in this campaign except GT-R.

^ Do not use disc 3/3.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 507

^ This NEW disc (Figure B) is required for all applied models in this campaign.

^ This disc replaces disc 3/3 above.

^ This disc also replaces disc NTB10-125b/NTB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.

NOTE:

Numbers on these discs do not match this bulletin's reference number or the campaign ID #.

^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.

^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number

1-(800) 347-8933. Request a new disc using the information printed on the disc.

CLAIMS INFORMATION

Submit a Campaign (CM) line claim using the claims coding:

Service Procedure

IMPORTANT:

Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function otherwise the Navigation System may continuously reboot the

next time it is turned on.

NOTE:

This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to

a low charge rate (trickle charge).

This SERVICE PROCEDURE contains three sections:

A. Disable Bluetooth(R) Function

B. Loading the Program - all except GT-R

Loading the Program for GT-R

C. Check Bluetooth(R) Setting - all except GT-R

Check Bluetooth(R) Setting for GT-R

A: Disable Bluetooth(R) Function

1. Set the parking brake.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 508

2. Turn the ignition ON and keep the transmission in Park or Neutral.

3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

4. Press the "SETTING button on the switch panel.

5. Touch "Bluetooth".

6. Make sure Bluetooth is OFF.

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is OFF when the ON indicator is "grayed-out".

7. Turn the ignition OFF and wait for 10 seconds.

8. Go to B: Loading the Program.

B: Loading the Program - all except GT-R For GT-R.

NOTE:

This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to

a low charge rate (trickle charge).

1. Turn the ignition ON - keep the transmission in Park or Neutral.

^ The navigation start-up screen should display.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 509

NOTE:

If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

4. Select "Navigation Version" on the display screen.

5. Check "Map Version".

^ If the Map Version is 09-10 MAP No. 1 or 09-10 MAP No.1a

a. Continue with Step 6.

^ If the Map Version is any other then above:

a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD/DVD player.

The other Discs will not be needed.

b. Skip to step 18.

6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

7. Insert disc ITB10-031 / NTB1-0068 (Disc 1/3) into the in-dash CD/DVD player.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 510

^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.

IMPORTANT:

Once reprogramming has started:

^ Do not eject a disc while it is loading.

^ Do not change the ignition position until all discs have been loaded.

^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.

8. Wait for the program to load (progress bar will display).

9. When the program has finished loading:

^ Disc will automatically eject, and

^ "Program loading is completed" will display.

10. Carefully remove the disc.

11. The navigation system will automatically restart.

12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).

13. Touch "DVD update".

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 511

14. Touch "Yes" to begin the map update process.

^ Map update will take about 15 minutes.

15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.

16. The navigation system will automatically restart.

17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).

18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:

^ If the screen in Figure 13 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Go to C: Check Bluetooth(R) Setting.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 512

^ If "Now preparing loading" shown in Figure 14 is displayed, reprogramming will begin automatically.

> Follow the on-screen Caution during the reprogram.

19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure 15)

^ Rewriting program data (Figure 16)

^ Rewriting language data (Figure 17)

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 513

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

20. When the first part of the program has finished loading:

^ "Program loading is completed" will be displayed (Figure 18).

^ The Re-programming Software DVD will automatically eject.

21. Remove the DVD and continue to the second part of the update (step 22).

22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 25 on the next page.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 514

23. "Rewriting boot data (Figure 20) and "Rewriting program data (Figure 21) will be displayed.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

24. After the reprogram has completed:

^ "Program loading is completed will be displayed (Figure 22).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 25.

After Navigation has restarted:

25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD

slot again.

One of the following screens will display:

^ If Figure 23 is displayed, it indicates that the reprogram has been completed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 515

> If complete, go to step 26.

^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 18.

> Follow steps 18 through 25 again.

26. Eject the DVD.

27. Go to C: Check Bluetooth(R) Setting.

C: Check Bluetooth(R) Setting (all except GT-R)

1. Press the "Setting button on the switch panel.

2. Touch "Bluetooth".

3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is ON when the ON indicator displays in orange.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 516

^ Bluetooth is OFF when the ON indicator is "grayed-out".

4. Turn the ignition OFF. The process is complete.

B: Loading the Program for GT-R

1. Turn the ignition ON.

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

5. Load the new disc "NTB12-070/ITB12-054 Re-programming Software DVD into CD slot of the audio unit.

One of the following screens will display:

^ If the screen in Figure A1 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Go to Check Bluetooth(R) Setting for GT-R.

^ If "Now preparing loading" shown in Figure A2 is displayed, reprogramming will begin automatically.

> Follow the on-screen Caution during the reprogram.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 517

6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure A3)

^ Rewriting program data (Figure A4)

^ Rewriting language data (Figure A5)

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

7. When the first part of the reprogram has finished loading:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 518

^ "Program loading" is completed will be displayed (Figure A6).

^ The Re-programming Software DVD will automatically eject.

8. Remove the DVD and continue to the second part of the update (step 9).

9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 12.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 519

10. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

11. After the reprogram has completed:

^ "Program loading is completed" will be display (Figure A10).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 12.

After Navigation has restarted:

12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD

slot again.

One of the following screens will display:

^ If Figure A11 is displayed it, indicates that the reprogram has been completed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 520

> If complete go to step 13.

^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 5.

> Follow steps 6 through 12 again.

13. Eject the DVD.

14. Go to C: Check Bluetooth(R) Setting for GT-R.

C: Check Bluetooth(R) Setting for GT-R

1. Press the "Setting button on the switch panel.

2. Touch "Bluetooth".

3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is ON when the ON indicator displays in orange.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 521

^ Bluetooth is OFF when the ON indicator is "grayed out".

4. Turn the ignition OFF. The process is complete.

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-135 Date: 091123

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-135 Date: 091123

Antitheft System - Electronic Steering Column Lock Info.

Classification: EL09-047

Reference: NTB09-135

Date: November 23, 2009

2010 MAXIMA/ALTIMA; ELECTRONIC STEERING COLUMN LOCK

APPLIED VEHICLES:

2010 Maxima (A35)

2010 Altima (L32, CL32, L32HV)

APPLIED VINS/DATES:

Vehicles built AFTER:

1N4AA5AP(*)AC 812165 / 30-Sep-2009 (A35)

1N4(*)L2(***)A C 051049 / 21-Jul-2009 (Smyrna L32)

1N4(*)L2(***)A N 400000 / 28-Jul-2009 (Canton L32)

SERVICE INFORMATION

Beginning with the Applied VINs/Dates shown above, the 2010 Altima and the 2010 Maxima are not equipped with an Electronic Steering Column

Lock (ESCL).

NOTE:

1. ESCL unlock steps are still required in I-Key Registration even though the ESCL is not present in these vehicles.

2. Please refer to the CONSULT III Operation Manual for proper steps regarding I-Key Registration.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-096 Date: 111019

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-096 Date: 111019

Audio/Cell Phone - IPod(R)/iPhone(R) USB Interface Issue

Classification: EL11-038

Reference: NTB11-096

Date: October 19, 2011

iPOD(R) / iPHONE(R) ISSUES USING VEHICLE USB INTERFACE

APPLIED VEHICLES: All Nissan vehicles equipped with a USB Interface

SERVICE INFORMATION

If an IPod(R)/ iPhone(R) related concern is verified on a vehicle while using the USB interface, perform the steps in this bulletin for initial

diagnosis.

NOTE:

For vehicles equipped with a Navigation system, make sure to confirm whether the customer is experiencing the issue while using the USB interface

or the Bluetooth(R) Audio Streaming feature. This bulletin applies only if the issue occurs while using the USB interface.

1. Power OFF/ON (restart/reset) the iPod(R)/ iPhone(R)

^ The restart/reset procedure is not the same for every iPod(R)/ iPhone(R). The restart/reset procedures can be found at www.apple.com/support.

2. Check the USB cable.

^ Some aftermarket cables can cause issues with USB connectivity. If the customer is using an iPod(R)/ iPhone(R), the best cable to use is the

Apple Inc. branded USB cable.

^ Make sure the cable does not have a short circuit or other concern.

3. Confirm the latest software is installed on the iPod(R)/ iPhone(R)

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 188

^ Many concerns are addressed by installing the latest iPod(R)/ iPhone(R) software update from Apple Inc.

^ View the software version of the iPod(R)/iPhonee(R) by navigating to the Settings area of the device, then selecting General > About or Settings.

^ Visit http://support.apple.com/downloads and select the applicable device to view the latest software update offered by Apple Inc.

4. If steps 1-3 have not resolved the concern:

a. Disconnect the cable from the USB interface.

b. Turn OFF the vehicle, wait one (1) minute, then turn the vehicle back to ACC or ON.

c. Connect a different USB device to the USB interface in the customer's vehicle, then try to duplicate the concern.

NOTE:

Other USB devices include a USB thumb drive formatted at either Fat16 or Fat32 with .mp3 or .wma files, or another type of iPod(R) (iTouch(R),

Classic(R), Nano(R), etc.).

d. If the concern still exists with a known good USB device, refer to the applicable Electronic Service Manual (ESM) for diagnosis on the USB

interface and/or AV Control Unit connectors.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-103B Date: 121031

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-103B Date: 121031

Navi/Audio Visual - Control Unit Diagnosis And Ordering

Classification: EL11-043B

Reference: NTB11-103B

Date: October 31, 2012

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 55

PREMIUM NAVI / AUDIO VISUAL CONTROL UNIT DIAGNOSIS AND ORDERING

This bulletin has been amended by adding to the APPLIED VEHICLES list, and the procedure to obtain the A/V unit part number. Please discard all

previous versions of this bulletin.

APPLIED VEHICLES

SERVICE INFORMATION

To improve customer satisfaction by providing the correct repair on the first visit, Nissan has revised the procedure for ordering an "exchange" or

"new" Audio Visual (A/V) Control Unit for vehicles with the premium navigation systems only (Refer to PROCEDURE).

^ To ensure a proper diagnosis and repair, the technician will need to call TECH LINE to confirm (or assist with) their diagnosis and the proper

repair prior to ordering the unit.

^ Clarion will require a confirmation from TECH LINE prior to shipping the exchange unit orders.

^ For the premium navigation system only.

^ Parts will be put on parts restriction and will need to be cleared prior to the order shipping.

^ The warranty claims call center will verify that TECH LINE has recommended replacement as part of the approval process in the event that a new

unit is required.

> TECH LINE has the support of engineering and Clarion in diagnosis if required.

NOTE:

All other A/V units will be ordered and shipped through the normal process.

> As usual, most units ordered should be an exchange unit versus a new unit.

This requirement of calling TECH LINE for confirmation to replace an A/V unit will be monitored to ensure the most effective and accurate method

of repair. Future changes or adjustments may be made to this process to increase repair timeliness and/or customer satisfaction.

A NEW UNIT IS REQUIRED ONLY IF:

^ The vehicle has not yet been sold.

^ The customer requests a new unit on a non-warranty repair.

^ The exchange unit is not available.

^ Insurance claim replacement.

NOTE:

Nissan would also recommend that this procedure is used for non-warranty repairs to ensure that a proper diagnosis and repair are performed.

PROCEDURE

a. Verify and duplicate the customers concern if possible. If duplication is not possible, please gather as much information about the incident

as possible from the service advisor/writer or customer.

b. Check for any connected devices (phone, iPod, MP3 player, etc.) or determine if a connected device is present during the concern. Please

gather model and software version information if possible.

c. Perform NTB09-063 for any Bluetooth concerns and NTB11-096 for any iPod / iPhone music play through USB concerns.

d. After gathering preliminary information of the concern, please call TECH LINE. After a diagnosis of the concern has been performed, and

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 56

the technician and TECH LINE agree that the unit should be replaced, the dealer can order the part.

e. TECH LINE will confirm with Clarion that the diagnosis has occurred.

f. After the order is confirmed with Clarion, an order/shipping confirmation fax will be sent to the dealer.

g. Before an order is placed, the technician/dealer will need to provide TECH LINE with the following information from the incident unit:

Obtain A/V Unit Part Number (Optional)

Obtain A/V Unit Part Number (OPTIONAL)

1. Make sure the shift selector is in Park (A/T) or Neutral (M/T), and the parking brake is set.

2. Connect the plus VI to the vehicle.

3. Turn the ignition ON.

NOTE:

You may want to start the engine to keep the battery charged during this procedure.

4. Write down customers radio station presets (presets will be lost during this procedure).

5. Open/start ASIST on the CONSULT PC, and then select CONSULT III plus.

6. Wait for the plus VI to be detected, and the status box(es) to turn "green".

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 57

7. Select the plus VI with the correct serial number being used (if more than one in the shop) by highlighting it in the Connection Status box.

8. Select Re/programming Configuration.

9. Use arrows (if needed) to view and read all Cautions.

10. Check the box confirming the precautions have been read.

11. Select Next.

12. Select the Automatic Selection (VIN) tab.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 58

13. Select Confirm.

^ Wait while system call completes.

14. Select Confirm.

15. Select Multi A/V.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 59

16. Select Read / Write Configuration.

17. Select Before Replace ECU.

18. Select Save.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 60

^ The software P/N is shown in Figure 10. Ignore it.

19. Select End.

NOTE:

Leave C-III plus running and the plus VI connected.

20. Turn OFF the audio system.

21. Put the A/V system into System Diagnostic Mode as follows:

a. Press and hold the SETTING button.

b. While holding the SETTING button, turn the volume control knob 40 clicks or more.

^ The volume control knob can be turned either direction.

^ When the system goes into the System Diagnostic Menu, the screen in Figure 12 will display.

22. Select Confirmation/Adjustment.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 61

23. Select Delete Unit Connection Log.

24. Select Yes.

25. Select Initialize Settings.

26. Select Accessory Number Initialization.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 62

27. Select Yes.

28. Wait while the system "initializes".

^ The screen in Figure 18 will display while "initializing".

^ The screen in Figure 19 will display when "initialization" is complete.

29. Once "initialization" is complete, reboot the Multi A/V system as follows:

a. Turn OFF the ignition.

b. Wait 10 seconds.

c. Turn ON the ignition.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 63

30. Select Diagnosis (One System).

31. Select MULTI AV.

32. Select the ECU identification tab.

33. Print or write down the ECU PART NUMBER for ordering and warranty information:

25915-_ _ _ _ _

34. Select Home.

The A/V unit can now be ordered with this part number. The current A/V unit can now be configured for use until it is replaced.

Configure the Multi AV System

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 64

Configure the Multi AV System

1. After selecting Home, the screen in Figure 23 will appear.

2. Select Re/programming Configuration.

3. Read the Precautions.

^ When finished, touch the Confirmed instructions box to insert a check mark, and then select Next.

4. Select Automatic Selection (VIN).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 65

5. Confirm the correct Model Name and Model Year are displayed.

^ When finished, select Confirm.

6. Select Confirm.

7. Select After Replace ECU.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 66

8. Select OK.

9. After selecting OK, the screen in Figure 30 appears.

10. Select End.

^ Configuration is now complete.

Close C-III plus, remove the plus VI, and then go to "Confirm Multi AV System is Operational".

Confirm Multi AV System Is Operational

Confirm Multi AV System Is Operational

1. Put your foot on the brake, and then turn the engine OFF (if running).

2. Start the engine, and then move the shift selector to R (Reverse).

3. If equipped, make sure the rear view monitor is working correctly.

4. Put the shift selector back into P (Park).

5. Turn ON the radio.

6. Turn the volume knob and make sure the audio volume responds to movement of the knob.

7. Reset the radio station presets.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-019A Date: 120827

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-019A Date: 120827

Wipers/Washers - Intermittent Wiper Operation Information

Classification: EL09-010A

Reference: NTB09-019A

Date: August 27, 2012

INTERMITTENT WIPER OPERATION

This bulletin has been amended to apply to all vehicles with Intermittent Rain Sensing Wipers.

APPLIED VEHICLE: Nissan vehicles with Intermittent Rain Sensing Wipers

SERVICE INFORMATION

Vehicle may be equipped with the Rain-Sensing Auto Wiper system.

With this system:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 87

> A rain sensor is located on the windshield, if equipped.

> When the wiper lever is pushed down to the intermittent (INT) position, the wipers will operate when the rain sensor detects rain.

> May only make a single stroke unless rain is detected directly above the sensor.

> May also be identified by the word "AUTO ADJ" on the wiper switch (some models).

NOTE:

The wipers may operate unexpectedly when dirt, fingerprints, oil film, or insects are located on or around the sensor, or when exhaust gas or

moisture affect the rain sensor.

If a customer states the wipers do not work when the wiper lever is pushed down to the intermittent (INT) position, make sure the customer is

familiar with the above information.

^ You can demonstrate the operation of the system by pushing the wiper lever down to the intermittent (INT) position and spraying/sprinkling water

over the rain sensor.

NOTE:

If a wiper-operation incident does occur, refer to the applicable Electronic Service Manual (ESM) for further diagnostic assistance.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-120A Date: 111007

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-120A Date: 111007

Interior - Front Seats Bind/Won't Move Fore/Aft

Classification: BT10-011A

Reference: NTB10-120A

Date: October 7, 2011

2007-2012 ALTIMA;

MANUAL DRIVER OR PASSENGER SEAT BINDS, OR WILL NOT MOVE, FORWARD AND BACKWARD

This bulletin has been amended to include additional model years to the The Applied Vehicles section. No other changes have been made.

APPLIED VEHICLE:

2007-2012 Altima Sedan (L32); with manual seats only

2007-2011 Altima Hybrid (L32HV); with manual seats only

IF YOU CONFIRM:

The driver and / or front passenger manual seat binds, or will not move, when adjusting forward or backward.

ACTION:

Repair the seat with the Service Kit.

^ Use the kit listed in the PARTS INFORMATION section below.

^ For repair procedure, go to SERVICE PROCEDURE.

NOTE:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 197

Do not replace the seat assembly for this incident, if it should occur.

IMPORTANT:

The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 198

Service Kit

Disclaimer

Service Procedure

Remove Seat Tracks

IMPORTANT

1. Write down all radio station presets.

2. Remove the incident seat from the vehicle.

^ For seat removal procedure, refer to BODY INTERIOR, SEAT of the appropriate Electronic Service Manual (ESM), if needed.

NOTE:

> Before seat removal, turn off the ignition switch, disconnect both battery cables (negative cable first), and then wait at least three (3) minutes.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 199

> When removing and installing, use suitable covering to protect the vehicle from damage.

> Do not use the slide release handle (for fore / aft adjustment) to lift the seat.

> Perform seat repairs in a clean work area, such as a work bench with suitable covering.

> The outer seat finishers extend to the rear. Be careful when laying the seat on its seatback.

CAUTION:

The front passenger seat is equipped with an Occupant Detection System sensor and control module. Do not disassemble the front passenger seat

cushion assembly or remove the trim as this will affect the Occupant Detection System's calibration.

NOTE:

Step 3 is for the driver seat only. For passenger seat, refer below to Step 4.

3. For lift type seats only: remove the seat lifter handle (see Figure 1).

a. To access the screws, pry off the lift lever finisher with a suitable tool (see Figure 1).

b. Remove the screws (see Figure 2).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 200

4. Remove the clips holding the seatback's lower fabric (see Figure 3).

5. Lift up on the seatback's lower fabric, and then remove the screw located at the rear of the outer finisher (see Figure 4).

CAUTION:

For passenger seats only, do not disassemble the seat cushion fabric, it's trim, or its attachments (see CAUTION above for more detail).

NOTE:

Removal of passenger seat outer finisher similar.

6. Remove the seat outer finisher.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 201

^ See Figure 5 for screw and clips location.

^ Passenger seat outer finisher similar.

7. Lay the seat on its seatback.

8. Remove the slide release handle return spring (return spring). See Figure 6.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 202

^ While holding the return spring on the one end, pry the other end of the return spring out of its positioning hole (see Figure 7).

9. Remove the nuts securing the outer seat slide track, and then remove the outer track and slide release handle (release handle). See Figure 8.

NOTE:

The passenger seat may have only three (3) nuts for each track. This is normal.

10. Remove the nuts securing the inner track, and then remove the inner track (see Figure 9).

11. Install the new inner track with new nuts (see Figure 9).

^ Nuts torque sequence: 1-2-3-4

^ Nuts torque: 30 Nm (3.0 kg-m, 22 ft-lb)

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 203

NOTE:

Replacement seat tracks have four studs. They are to replace both 3- and 4-stud seat tracks.

12. Install the release handle and return spring to the inner track.

^ See Figure 10 for return spring position.

13. Install the outer track to the release handle and seat (no picture shown).

^ Install the nuts finger tight at this time.

14. Adjust the tracks to measure 430 mm (16-15/16 inches) between each locator pin, and then slightly tighten the nut of the outer track closest to the

locator pin (see Figure 11 above).

15. Adjust the tracks to measure 430 mm (16-15/16 inches) between the center of each track hole, and then torque the outer track nuts (see Figure

11).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 204

^ Nuts torque sequence: 1-2-3-4 (see Figure 12)

^ Nuts torque: 30 Nm (3.0 kg-m, 22 ft-lb)

NOTE:

Replacement seat tracks have four studs. They are to replace both 3- and 4-stud seat tracks.

16. Re-check both measurements.

^ If measurements do not match the values given above, loosen the outer track nuts, and then repeat Step 14 and 15.

17. Install the outer seat finisher. Refer to Figure 5.

18. Position the the seatback's rear fabric under both seat finisher ends, and then secure the clips (see Figure 13).

19. Install the seat in the vehicle.

^ Install and torque the seat-to-body bolts in the following order:

Front inner

Front outer

Rear inner

Rear outer

^ Seat bolts torque: 49 Nm (5.0 kg-m, 36 ft lb)

^ For seat installation procedure, refer to BODY INTERIOR, SEAT of the appropriate ESM, if needed.

^ Do not use the release handle to lift the seat.

^ If the tracks are not aligned, lift up on the release handle, and then adjust as needed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 205

20. Verify the seat operates normally; make sure both tracks lock into place after fore / aft adjustment.

21. Reconnect both battery cables, negative cable last.

22. Reset / initialize all applied systems i.e., radio, clock, sunroof, etc.

^ Program customer's radio presets from step 1 back into audio unit.

When your family car is faster than a GTR

2014 Nissan-Datsun Altima Diagrams. DTC # 09-140 Date: 091208

2014 Nissan-Datsun Altima Diagrams. DTC # 09-140 Date: 091208

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 392

A/T - CVT Oil Leak Diagnosis Information

Classification: AT09-012

Reference: NTB09-140

Date: December 8, 2009

CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE

APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)

SERVICE INFORMATION

If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.

1. Thoroughly clean off the area of the suspected leak.

2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.

3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).

4. Inspect with lamp from J-43926 A/C Dye Kit*

If no fluorescent oil trace/leak is found, the stain is probably:

^ corrosion protection chemicals sprayed on the transmission

and/or

^ lubricants which are sometimes used to ease the assembly process.

NOTE:

These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.

If a fluorescent oil trace/leak is found:

^ Repair using standard warranty procedures.

*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.

NOTE:

The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-045 Date: 110425

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-045 Date: 110425

Body - Carpet Wet/Water Leak From Sunroof

Classification: BT11-013

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 311

Reference: NTB11-045

Date: April 25, 2011

ALTIMA AND MAXIMA; SUNROOF FRONT DRAIN HOSE IS KINKED, PINCHED, OR DISCONNECTED

APPLIED VEHICLES:

2007-2011 Altima Sedan (L32)

2008-2011 Altima Coupe (CL32)

2009-2011 Maxima (A35)

SERVICE INFORMATION

A wet carpet or water leaking from the sunroof/headliner may be related to the sunroof drain hoses.

If the front RH or LH sunroof drain hose is found to be kinked or pinched in the lower dash area:

^ Replace the drain hose with a new one.

NOTE:

Follow the standard Electronic Service Manual (ESM) procedures when replacing the front RH or LH sunroof drain hose.

If the front RH or LH sunroof drain hose is found to be disconnected only and not kinked or pinched:

^ Reconnect the drain hose. Do not replace the drain hose.

2014 Nissan-Datsun Altima Diagrams. DTC # 09-111B Date: 100901

2014 Nissan-Datsun Altima Diagrams. DTC # 09-111B Date: 100901

Interior - Driver's Seat Bottom Shifts/Rocks Slightly

Classification: BT09-057B

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 455

Reference: NTB09-111B

Date: September 1, 2010

2008-2010 ALTIMA COUPE; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY

This bulletin has been amended. Replacement of the seat side finisher has been added to the service procedure and the Parts Information has been

updated. Please discard previous versions.

APPLIED VEHICLES: 2008-2010 Altima Coupe (CL32) -equipped with power seat

APPLIED VIN:

2008-2009 vehicles - All

2010 vehicles built before 1N4(*)L2E(**)A(*) 117207

APPLIED DATE: Vehicles built on or before November 18, 2009

IF YOU CONFIRM:

The driver seat bottom (power seat only) very slightly "rocks" and/or "shifts" back and forth when accelerating, braking, or when making a turn.

ACTION:

Replace the driver seat cushion frame assembly (adjuster assembly) with a new one.

^ During reassembly use a new side seat finisher.

IMPORTANT:

The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 456

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down all radio station pre-sets.

2. If equipped - write down / record the following customer settings for the ATC (Automatic Temperature Control) system. (Refer to the Service

Manual as needed):

^ Temperature Setting Trimmer

^ Foot Position Setting Trimmer

^ Inlet Port Memory Function

3. Turn the ignition switch OFF.

4. Disconnect both battery cables - negative cable first.

5. WARNING: Wait for at least 3 minutes before removing the driver seat.

6. Carefully remove the driver seat from the vehicle.

^ Refer to the Service Manual section SE for seat removal procedure.

CAUTION:

Use covers as needed to protect interior surfaces from being scratched or damaged.

7. Replace the cushion frame assembly (adjuster assembly).

^ Refer to the 2010 Altima Coupe Service Manual - SE Section, Front Seat Driver Side: Disassembly and Assembly.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 457

^ During reassembly use a new side finisher listed in the Parts Information.

NOTE:

This bulletin contains additional helpful information for Seatback Finisher Removal (See below).

8. Connect the battery cables - positive cable first.

9. Reset the clock and the radio station presets.

10. Refer to the Service Manual for the following "reset / relearn procedures:

^ Power Window Initialization

^ Sunroof Memory Reset/Initialization

^ ATC Temperature Setting Trimmer (A/C system)

^ ATC Foot Position Setting Trimmer (A/C system)

^ ATC Inlet Port Memory Function - FRE and REC (A/C system)

^ Rear View Monitor Possible Route Line Center Position Adjustment (if equipped)

^ Steering Angle Sensor Neutral Position

11. Inform the customer they will need to "reset" their Automatic Drive Positioner.

Seatback Finisher Removal

1. Move / adjust the seat bottom and seat back to the full forward positions.

NOTE:

The seat back finisher is held on with:

^ 2 top hooks

^ 2 side clips

^ 2 bottom clips

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 458

2. Reach under the seat and disconnect the 2 elastic straps for the toe flap.

3. Insert your fingers behind the bottom corner of the finisher.

4. Locate the bottom clip with your fingers.

5. Pull the finisher next to the clip to unsnap the clip.

6. Repeat 3, 4 and 5 for the other bottom clip.

7. Insert your fingers into the side of the finisher.

8. Locate the "side" clip.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 459

9. Support the finisher with the palm of your hand.

10. Pull the finisher next to the clip to unsnap the clip.

11. Repeat 7 to 10 for the other "side" clip.

12. Pull down on the finisher to remove it.

2017 Nissan-Datsun Altima Technical Service Bulletin # 04-049H Date: 110413

2017 Nissan-Datsun Altima Technical Service Bulletin # 04-049H Date: 110413

Electrical - Trailer Light Wiring Info.

Classification: EL03-043H

Reference: NTB04-049H

Date: April 13, 2011

TRAILER LIGHT WIRING

This bulletin has been amended. The Applied Vehicles have been updated. Please discard previous versions of this is bulletin.

APPLIED VEHICLES

SERVICE INFORMATION

NOTE:

This bulletin provides information to be shared with all affected customers.

^ This TSB contains the appropriate hookup points for connecting a trailer light wiring harness to the towing vehicle's electrical system.

^ The wiring diagrams contained in this bulletin are for Nissan vehicles that have trailer towing capability (see the owners manual) but do not have a

Genuine Nissan accessory towing kit (with wiring) available.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 318

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 319

^ When splicing into the vehicle electrical system, a power-type module/converter must be used to provide power for all trailer lighting. A

power-type module/converter uses the vehicle battery as a direct power source for all trailer lights while using the vehicle taillight, stoplight, and

turn signal circuits only as a signal source. (See the illustration above.) The module/converter must draw no more than 5 milliamps from the

vehicle turn signal circuits and no more than 15 milliamps from the stop and tail light circuits.

CAUTION:

Using a module/converter that exceeds these power requirements listed above may negatively affect the performance and function of the vehicle's

electrical system.

See a professional trailer dealer or trailer rental agency for installation of the proper equipment.

Customers who inquire about towing should be reminded of the following:

^ Always check for correct operation of the turn signals, stoplights, and taillights every time a trailer is hitched up for towing.

^ The towing capacity for 350Z (Coupe Only), Altima, Maxima, and Sentra is 1,000 lbs.

For more information, refer customers to the Owner's Manual as well as the Nissan Towing Guide, available online at NissanUSA.com.

or go to http://www.safercar.gov.2017 Nissan-Datsun Altima Technical Service Bulletin # 10-105 Date: 100917

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 08-072A Date: 101007

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 08-072A Date: 101007

Interior - Rough Driver's Power Seat Operation

Classification: EL08-005A

Reference: NTB08-072A

Date: October 7, 2010

2007-2010 ALTIMA; DRIVERS POWER SEAT SLIDE TRAVEL ROUGH

This bulletin has been amended. The Relevant Vehicles and the Parts Information has changed.

RELEVANT VEHICLES:

2007-2010 Altima (L32)

2007-2010 Altima Hybrid (L32HV)

IF YOU CONFIRM

The driver's power seat slide travel front to back is rough.

ACTION

For all 2010 Altimas and 2009 Altimas built from:

^ 1N4(*)L(*)1E(*)9 C 151712/5-Nov-2008

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 460

^ 1N4(*)L(*)1E(*)9 N 453274/4-Nov-2008

Install the Power Track Service Kit to resolve the issue. Refer to the Service Procedure.

NOTE:

Do not replace the seat bottom or seat lower assembly for this issue, if it should occur.

For 2007 through 2009 Altimas built to:

^ 1N4(*)L(*)1E(*)9 C 151711/5-Nov-2008

^ 1N4(*)L(*)1E(*)9 N 453273/4-Nov-2008

This bulletin does not apply. Replace the Seat Lower Assembly using standard Nissan Warranty Practices.

IMPORTANT:

The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down the radio station presets.

2. Slide the driver's seat fully rearward and remove the front two seat-to-body bolts.

3. Tilt the seat back to the upright position and remove the headrest.

4. Slide the seat mid-travel, raise the seat all the way up, and remove the rear seat-to-body bolts.

5. Disconnect both 12V battery cables, negative cable first, and wait at least 3 minutes before proceeding to step 6.

6. Disconnect the seat harnesses from the body harnesses.

7. Remove the seat from the vehicle.

8. Place the seat, back side down, on a clean covered workbench.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 461

9. Remove the seat bottom plastic side shields.

10. Disconnect the power harness and clip from the track motor.

11. Remove all eight nuts holding the lower seat track to the seat as shown. The lower rack will not be reused.

12. Remove the new track assembly from the shipping package and lay it next to the seat as shown.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 462

13. Set the seat assembly onto all eight studs of the new lower track assembly.

14. Tighten all eight nuts in sequence as shown.

15. Remove the four bolts and the plastic bracket. The plastic bracket will not be reused.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 463

16. Connect the track motor power harness and clip.

17. Reinstall the plastic shields.

18. Reinstall the seat into the vehicle, reconnecting the seat harnesses to the body harnesses while doing so.

IMPORTANT:

Be sure that all Side Air Bag harnesses are routed correctly and that all connectors are firmly seated.

19. Install the four seat-to-body bolts in the sequence shown in Figure 7

TORQUE: 40 Nm (3.9 kg-m, 35 ft-lb).

20. Reinstall the headrest.

21. Reconnect the battery cables.

22. Check seat for proper operation.

23. Reprogram the radio presets.

24. Reinitialize power windows and other systems as needed.

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-009 Date: 100119

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-009 Date: 100119

Engine Controls - Seized O2 Sensor Removal Procedure

Classification: EM09-015

Reference: NTB10-009

Date: January 19, 2010

REMOVAL PROCEDURE FOR SEIZED EXHAUST SENSOR

APPLIED VEHICLES: All Nissan vehicles

SERVICE INFORMATION

If an exhaust sensor is seized in the exhaust manifold/catalyst/front tube, perform the procedure described in this bulletin to remove the sensor and

prevent unnecessary replacement of the exhaust manifold/catalyst/front tube.

In most cases this procedure is successful. This is because the threads of the exhaust sensors are made of a softer material than the part they thread

into on the exhaust manifold/catalyst/front tube.

NOTE:

The replacement of exhaust manifolds/catalysts/front tubes for stripped exhaust sensor threads may not be considered a warrantable expense.

This procedure can be performed by two methods:

Method #1 - If the Sensor Can Be Easily Accessed

^ The procedure can be performed on the vehicle.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 388

^ The exhaust manifold/catalyst/front tube will not have to be removed.

Method #2 - If the Sensor Cannot Be Easily Accessed

^ The exhaust manifold/catalyst/front tube must be removed from the vehicle.

^ The procedure will be performed with the part clamped in a vice.

Method #2 is described in this bulletin. Method #1 is the same as Method #2 except that it is performed on the vehicle.

Service Procedure

Rust Penetrant

Recommended rust penetrants to be used in this procedure:

NOTES:

^ Rust penetrant is considered a shop supply.

^ Nissan Rust Penetrant can be ordered through the Nissan Direct Ship Chemical Care Product Program, Website order via link on dealer portal.

^ WD-40 is available from various local sources.

Removal Tool

^ When removing a seized exhaust sensor with a specialty socket (which contains a slit to accommodate the wiring harness), it may spread open and

strip the sensor.

^ Before this occurs, it is recommended to cut the wiring harness from the sensor and use a box end wrench or 6-point deep well socket.

1. Clamp the exhaust manifold/catalyst/front tube in a vice.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 389

2. Spray the sensor with the rust penetrant for 2 to 3 seconds.

^ It is important that the spray is directed at the base of the sensor to ensure it penetrates into the threads.

3. Loosen the sensor approximately 10 degrees.

4. Spray with rust penetrant again for 2 to 3 seconds.

5. Tighten the sensor 10 degrees, then loosen the sensor 10 degrees.

^ Repeat this motion several times until the sensor begins to turn more easily.

6. Continue the tightening/loosening motion while gradually unscrewing the sensor. Stop when the sensor will not unscrew any further.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 390

7. Spray with rust penetrant again for 2 to 3 seconds.

8. Repeat steps 6 and 7 until the sensor is removed.

9. Use compressed air to remove any metal debris from inside the boss threads.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

10. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.

11. Spray the boss threads with rust penetrant for 2 to 3 seconds.

12. Run a thread chaser through the boss to clean the threads.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 391

^ Use Kent Moore part number J-43897-18 or J43897-12.

13. Use compressed air to remove any remaining debris.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

14. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.

15. Tilt the manifold/catalyst/front tube so that the metal debris falls out of the part.

16. Apply compressed air through the boss to blow out any remaining debris.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

17. Install the new sensor as described in the applicable Electronic Service Manual (ESM).

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-017 Date: 100201

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-017 Date: 100201

Instruments - Fuel Gauge Issues/DTC's P0461/P0462/P0463

Classification:

EL09-030

Reference:

NTB10-017

Date:

February 1, 2010

ALTIMA AND MAXIMA; FUEL GAUGE ISSUES

AND/OR DTC P04611 P0462 / P0463

APPLIED VEHICLES:

2007-2010 Altima (L32)

2008-2010 Altima Coupe (CL32)

2008-2010 Altima Hybrid (L32HV)

2009-2010 Maxima (A35)

IF YOU CONFIRM:

The fuel gauge is erratic, inaccurate, or inoperative

And / Or

The MIL is "ON with DIG P0461, P0462, or P0463 stored in Self-Diagnosis.

ACTION:

Replace the fuel level sensor unit.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 394

^ Refer to the SERVICE PROCEDURE section of this bulletin for repair procedure.

^ Use the parts listed in the PARTS INFORMATION section in this bulletin.

NOTE:

Do not replace the entire fuel pump module assembly for this incident, if it should occur.

IMPORTANT:

The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

Submit a Primary Failed Part (PP) line claim using the claims coding shown.

NOTE:

Version 1 fuel pump module assembly fits on earlier model year Altima models. Version 2 fits on later Altima and all Maxima models.

SERVICE PROCEDURE

1. Remove the fuel pump module assembly (module).

^ Refer to the appropriate section of the Electronic Service Manual (ESM), if needed.

NOTE:

Perform repairs in a clean work environment.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 395

2. Determine which version module you are working on (see Version 1 and 2).

3. Remove the 3 wire terminals with red, white, and double-wire black wires from under the top of the module as shown in Figure 1.

NOTE:

The white wire may appear yellowish in color.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 396

^ Press the tab in and gently pull the wire off its terminal (see Figure 2)

4. Remove the plastic tie strap that holds the wires to the fuel supply hose (supply hose) as shown in Figure 3.

CAUTION:

Be careful not to damage the supply hose or wiring when removing the tie strap.

5. Remove the fuel tank temperature sensor (temp sensor) from its retention feature (see Figure 4).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 397

6. Version 1: Remove the temp sensor wires from the retention feature (see Figure 5).

7. Version 2 only: Remove the temp sensor wires from both retention features (see Figure 6).

8. Version 1 only: Remove all wires from the retention feature on the module (see Figure 7).

NOTE:

This retention feature is not reused.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 398

9. Version 1 only: Remove the black plastic retainer (retainer) as shown in Figure 8.

^ Pry on the clip ends using a pocket screwdriver or suitable tool, one side at a time (see Figure 8).

10. Remove the level sensor from the module (see Figure 9).

Push the tab inward, and then push the level sensor up, and then pull it away from the module.

11. Install the new level sensor onto the module (no picture shown).

Perform Step 10 in reverse, making sure its tab locks into place.

12. Version 1 only: Reinstall the retainer by snapping it into place (see Figure 10).

^ Make sure the level sensor's wires are not pinched under the retainer.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 399

13. Install the temp sensor into its retention feature (see Figure 11).

14. Version 1 only: Install the temp sensors wiring into the retention feature as shown in Figure 12.

^ Route the temp sensor's wires to the right of the level sensor.

^ Make sure the wiring is clear of float arm movement.

^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.

15. Version 2 only: Secure the level sensors wires into the retention features (see Figure 13).

^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 400

16. Route the wires on the inside of the supply hose (see Figure 14).

17. Secure the wires to the supply hose with a tie strap as shown in Figure 14.

CAUTION:

Be careful not to damage the supply hose or wires when installing the tie strap.

^ Step 17 applies to both module versions.

NOTE:

Tie straps are considered a shop supply.

18. Install the wires to the correct terminals (see Figure 15 below).

^ Make sure the wires are routed correctly as shown in Figure 15.

--> Red and white wires are routed in front of the blue wire.

--> The double black wire is in between the blue and single black wires.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 401

^ Make sure the tabs are securely locked.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-111B Date: 100901

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-111B Date: 100901

Interior - Driver's Seat Bottom Shifts/Rocks Slightly

Classification: BT09-057B

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 455

Reference: NTB09-111B

Date: September 1, 2010

2008-2010 ALTIMA COUPE; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY

This bulletin has been amended. Replacement of the seat side finisher has been added to the service procedure and the Parts Information has been

updated. Please discard previous versions.

APPLIED VEHICLES: 2008-2010 Altima Coupe (CL32) -equipped with power seat

APPLIED VIN:

2008-2009 vehicles - All

2010 vehicles built before 1N4(*)L2E(**)A(*) 117207

APPLIED DATE: Vehicles built on or before November 18, 2009

IF YOU CONFIRM:

The driver seat bottom (power seat only) very slightly "rocks" and/or "shifts" back and forth when accelerating, braking, or when making a turn.

ACTION:

Replace the driver seat cushion frame assembly (adjuster assembly) with a new one.

^ During reassembly use a new side seat finisher.

IMPORTANT:

The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 456

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down all radio station pre-sets.

2. If equipped - write down / record the following customer settings for the ATC (Automatic Temperature Control) system. (Refer to the Service

Manual as needed):

^ Temperature Setting Trimmer

^ Foot Position Setting Trimmer

^ Inlet Port Memory Function

3. Turn the ignition switch OFF.

4. Disconnect both battery cables - negative cable first.

5. WARNING: Wait for at least 3 minutes before removing the driver seat.

6. Carefully remove the driver seat from the vehicle.

^ Refer to the Service Manual section SE for seat removal procedure.

CAUTION:

Use covers as needed to protect interior surfaces from being scratched or damaged.

7. Replace the cushion frame assembly (adjuster assembly).

^ Refer to the 2010 Altima Coupe Service Manual - SE Section, Front Seat Driver Side: Disassembly and Assembly.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 457

^ During reassembly use a new side finisher listed in the Parts Information.

NOTE:

This bulletin contains additional helpful information for Seatback Finisher Removal (See below).

8. Connect the battery cables - positive cable first.

9. Reset the clock and the radio station presets.

10. Refer to the Service Manual for the following "reset / relearn procedures:

^ Power Window Initialization

^ Sunroof Memory Reset/Initialization

^ ATC Temperature Setting Trimmer (A/C system)

^ ATC Foot Position Setting Trimmer (A/C system)

^ ATC Inlet Port Memory Function - FRE and REC (A/C system)

^ Rear View Monitor Possible Route Line Center Position Adjustment (if equipped)

^ Steering Angle Sensor Neutral Position

11. Inform the customer they will need to "reset" their Automatic Drive Positioner.

Seatback Finisher Removal

1. Move / adjust the seat bottom and seat back to the full forward positions.

NOTE:

The seat back finisher is held on with:

^ 2 top hooks

^ 2 side clips

^ 2 bottom clips

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 458

2. Reach under the seat and disconnect the 2 elastic straps for the toe flap.

3. Insert your fingers behind the bottom corner of the finisher.

4. Locate the bottom clip with your fingers.

5. Pull the finisher next to the clip to unsnap the clip.

6. Repeat 3, 4 and 5 for the other bottom clip.

7. Insert your fingers into the side of the finisher.

8. Locate the "side" clip.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 459

9. Support the finisher with the palm of your hand.

10. Pull the finisher next to the clip to unsnap the clip.

11. Repeat 7 to 10 for the other "side" clip.

12. Pull down on the finisher to remove it.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-050 Date: 110513

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-050 Date: 110513

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 276

Interior - Revised Seat Back Service Procedure

Classification: BT11-019

Reference: NTB11-050

Date: May 13, 2011

2007-2011 ALTIMA; REVISED FRONT SEAT BACK SERVICE PROCEDURES

APPLIED VEHICLES: 2007-2011 Altima Coupe, Sedan, and Hybrid (C/L32/HV)

SERVICE INFORMATION

For 2007-2011 Altima vehicles, new front seat back disassembly and assembly procedures have been developed as the result of some service parts

now being available (for example, seat side air bag module).

Updated Service Manuals for 2010-2011 Altima vehicles will be distributed to the field as quickly as possible. For 2007-2009 vehicles, the updated

procedures will be available on ASIST as a Service Manual Amendment (SMA).

Until the updated Service Manuals are made available, please use the updated service information shown below if you need to service the front seat

back(s) for any reason.

NOTE:

The standard Flat Rate Times will be updated to reflect the new procedures.

Refer to images below view the revised SEAT (SE) section information.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 277

Index/Contents

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 278

SE-2

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 279

SE-3

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 280

SE-4

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 281

SE-5

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 282

SE-6

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 283

SE-7

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 284

SE-8

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 285

SE-9

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 286

SE-10

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 287

SE-11

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 288

SE-12

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 289

SE-13

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 290

SE-14

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 291

SE-15

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 292

SE-16

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 293

SE-17

COUPE - UNIT DISASSEMBLY AND ASSEMBLY

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 294

SE-18

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 295

SE-19

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 296

SE-20

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 297

SE-21

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 298

SE-22

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 299

SE-23

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 300

SE-24

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 301

SE-25

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 302

SE-26

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 303

SE-27

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 304

SE-28

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 305

SE-29

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 306

SE-30

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 307

SE-31

SEDAN - UNIT DISASSEMBLY AND ASSEMBLY