2017 Nissan-Datsun Altima Technical Service Bulletin # 10-009 Date: 100119

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-009 Date: 100119

Engine Controls - Seized O2 Sensor Removal Procedure

Classification: EM09-015

Reference: NTB10-009

Date: January 19, 2010

REMOVAL PROCEDURE FOR SEIZED EXHAUST SENSOR

APPLIED VEHICLES: All Nissan vehicles

SERVICE INFORMATION

If an exhaust sensor is seized in the exhaust manifold/catalyst/front tube, perform the procedure described in this bulletin to remove the sensor and

prevent unnecessary replacement of the exhaust manifold/catalyst/front tube.

In most cases this procedure is successful. This is because the threads of the exhaust sensors are made of a softer material than the part they thread

into on the exhaust manifold/catalyst/front tube.

NOTE:

The replacement of exhaust manifolds/catalysts/front tubes for stripped exhaust sensor threads may not be considered a warrantable expense.

This procedure can be performed by two methods:

Method #1 - If the Sensor Can Be Easily Accessed

^ The procedure can be performed on the vehicle.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 388

^ The exhaust manifold/catalyst/front tube will not have to be removed.

Method #2 - If the Sensor Cannot Be Easily Accessed

^ The exhaust manifold/catalyst/front tube must be removed from the vehicle.

^ The procedure will be performed with the part clamped in a vice.

Method #2 is described in this bulletin. Method #1 is the same as Method #2 except that it is performed on the vehicle.

Service Procedure

Rust Penetrant

Recommended rust penetrants to be used in this procedure:

NOTES:

^ Rust penetrant is considered a shop supply.

^ Nissan Rust Penetrant can be ordered through the Nissan Direct Ship Chemical Care Product Program, Website order via link on dealer portal.

^ WD-40 is available from various local sources.

Removal Tool

^ When removing a seized exhaust sensor with a specialty socket (which contains a slit to accommodate the wiring harness), it may spread open and

strip the sensor.

^ Before this occurs, it is recommended to cut the wiring harness from the sensor and use a box end wrench or 6-point deep well socket.

1. Clamp the exhaust manifold/catalyst/front tube in a vice.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 389

2. Spray the sensor with the rust penetrant for 2 to 3 seconds.

^ It is important that the spray is directed at the base of the sensor to ensure it penetrates into the threads.

3. Loosen the sensor approximately 10 degrees.

4. Spray with rust penetrant again for 2 to 3 seconds.

5. Tighten the sensor 10 degrees, then loosen the sensor 10 degrees.

^ Repeat this motion several times until the sensor begins to turn more easily.

6. Continue the tightening/loosening motion while gradually unscrewing the sensor. Stop when the sensor will not unscrew any further.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 390

7. Spray with rust penetrant again for 2 to 3 seconds.

8. Repeat steps 6 and 7 until the sensor is removed.

9. Use compressed air to remove any metal debris from inside the boss threads.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

10. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.

11. Spray the boss threads with rust penetrant for 2 to 3 seconds.

12. Run a thread chaser through the boss to clean the threads.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 391

^ Use Kent Moore part number J-43897-18 or J43897-12.

13. Use compressed air to remove any remaining debris.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

14. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.

15. Tilt the manifold/catalyst/front tube so that the metal debris falls out of the part.

16. Apply compressed air through the boss to blow out any remaining debris.

CAUTION:

DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.

17. Install the new sensor as described in the applicable Electronic Service Manual (ESM).