Tuesday, June 18, 2019
Monday, June 17, 2019
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-153 Date: 101223
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-153 Date: 101223
Brakes - Feel More Sensitive Than Expected
Classification: BR10-013
Reference: NTB10-153
Date: December 23, 2010
2010-2011 ALTIMA AND MAXIMA;
BRAKES FEEL MORE SENSITIVE THAN EXPECTED
APPLIED VEHICLES:2010-2011 Altima Sedan & Coupe (L32 & CL32)
2010-2011 Maxima (A35)
APPLIED VINs: 2010 Altima built after:
1N4(*)L2(***)AC 173905 (Smyrna) or 1N4(*)L2(***)AN 527905 (Canton)
2011 Altima built before:
1N4(*)L2(***)BC 105774 (Smyrna) or 1N4(*)L2(***)BN 407818 (Canton)
2010 Maxima built after: 1N4AA5AP(*)AC 862521
2011 Maxima built before: 1N4AA5AP(*)BC 807780
APPLIED DATE Vehicles built between June 9, 2010 and September 21, 2010
IF YOU CONFIRM
The brakes feel more sensitive than expected with light to moderate brake application,
and/or
Towards the end of bringing the vehicle to a stop (last few feet), the vehicle stops SLIGHTLY quicker than expected.
ACTION
Replace the Brake Booster Assembly
^ Refer to section BR in the appropriate Service Manual for brake booster replacement information.
^ Use the new brake booster listed in the Parts Information.
PARTS INFORMATION
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 223
Sunday, June 16, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621
Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.
Classification: EC10-017
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252
Reference: NTB10-079
Date: June 21, 2010
MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED
APPLIED VEHICLES: 2002 and later Nissan vehicles
IF YOU CONFIRM
The MIL is "ON" with P0128 (Thermostat Function) stored.
ACTIONS
1. Check to see if an aftermarket remote starter system is installed.
^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.
2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.
3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
Engine - Oil Leakage From The Upper End Of Oil Cooler
Classification:
EM10-002b
Reference:
NTB11-015b
Date:
February 1, 2013
ALTIMA SEDAN AND COUPE, SENTRA, AND ROGUE WITH QR25DE ENGINE; OIL LEAK
This bulletin has been amended in APPLIED VEHICLES, SERVICE PROCEDURE, PARTS INFORMATION, and CLAIMS INFORMATION.
Discard all previous versions of this bulletin.
APPLIED VEHICLES:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 488
2007 - 2012 Altima Sedan (L32)
2008 - 2013 Altima Coupe (CL32)
2007-2012 Sentra (B16)
2008 - 2013 Rogue (535)
APPLIED ENGINE:
QR25DE (4 cyl)
IF YOU CONFIRM:
Oil is leaking from the upper end of the engine oil cooler (oil cooler). See Figure 1.
ACTION:
Reseal the oil cooler with the parts listed in the PARTS INFORMATION.
^ For repairs refer to SERVICE PROCEDURE.
NOTE:
Do not replace the complete engine oil cooler assembly for this incident if it should occur.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 489
CLAIMS INFORMATION
SERVICE PROCEDURE
1. Remove the oil cooler from the engine block.
^ Refer to the appropriate section of the Electronic Service Manual (ESM) if needed.
^ Perform repairs in a clean work environment.
2. Remove the four (4) bolts, and then remove the upper half of the oil cooler. See Figure 2.
3. Remove the O-ring gasket, and then thoroughly clean out the gasket area and around it with a suitable cleaner.
^ The dashed line in Figure 3 shows the O-ring gasket area to be cleaned.
^ Make sure no debris or contaminants get into the holes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 490
^ Also clean underneath the upper half of the oil cooler (no picture shown).
4. Lightly coat the new O-ring gasket (see PARTS INFORMATION) with engine oil, and then put it in place. See Figure 4.
5. Install the upper half of the oil cooler with the bolts.
6. Torque the bolts in two steps: first step at half value, and then the second step at full value (listed below).
^ Bolts torque sequence:
1-2-3-4-5-6-7-8 (see Figure 5).
^ Bolts torque:
4.0 N.m (0.41 kg-m, 35.4 in lb)
7. Install the oil cooler to the engine with a new gasket (see PARTS INFORMATION).
Refer to the appropriate section of the ESM if needed.
Saturday, June 15, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-080 Date: 110824
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-080 Date: 110824
Steering/Suspension - Rear Axle Bolt/Torque Change
Classification: RA11-002
Reference: NTB11-080
Date: AUGUST 24, 2011
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 236
ALTIMA AND MAXIMA;
AXLE BOLT AND TORQUE CHANGE
APPLIED VEHICLES:
2002-2012 Altima Coupe, Sedan, and Hybrid (L31, C/L32/HV)
2004-2012 Maxima (A34, A35)
SERVICE INFORMATION
If bolt 56280-JA000 needs to be replaced in the following location:
^ Rear Shock Absorber to Rear Knuckle (see Figure 1 above)
...AND the vehicle is 2002-2012 Altima or 2004-2012 Maxima,
1. Order bolt 56280-JA00A instead of 56280-JA000.
2. Torque bolt 56280-JA00A to 80-100 Nm (8.2-10.2 kg-m, 59-74 ft-lb).
If bolt 56280-JA000 needs to be replaced in the following location:
^ Front Lower Link to Rear Knuckle (see Figure 1)
...AND the vehicle is 2007-2012 Altima or 2009-2012 Maxima,
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 237
1. Order bolt 56280-JA00A instead of 56280-JA000.
2. Torque bolt 56280-JA00A to 83-103 Nm (8.5-10-5 kg-m, 61-76 ft-lb).
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-074 Date: 120912
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-074 Date: 120912
Computers/Controls - CONSULT III Plus(R) Saved Data List
Classification: EC12-021
Reference: NTB12-074
Date: September 12, 2012
SAVED DATA LIST REPROGRAMMING WITH CONSULT III PLUS
SERVICE INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 84
^ When performing a "Reprogramming" operation with C-III plus, the screen in Figure 1 may display.
^ This screen displays "Saved Data" from previous C-III plus operations.
^ During the initial "Reprogramming Confirmation" set-up, if you get this screen:
1. Select Delete, then
2. Select Other Operation, then
3. Continue with the reprogramming procedure.
NOTE:
If reprogramming does not complete, this screen can display for reprogramming recovery. Do not select Delete if this screen displays
during reprogram recovery.
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
Campaign P1234 - Navigation Software Update For Various Issues
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 522
Reference:
NTB11-073a
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN CALL WAITING FUNCTION NAVIGATION UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
CAMPAIGN ID #: P1234
APPLIED VEHICLES:
2010-2011 Altima Sedan, Coupe, and Hybrid (L32, CL32, & L32HV)
2010-2011 Maxima (A35)
2010 - 2011 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, iPod(R), and voice recognition functions may not be working as intended. To
remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or
labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system.
IDENTIFICATION NUMBER
Nissan has assigned identification number P1234 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for 2010 models in this campaign.
^ Do not use disc 3/3.
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 523
^ This disc also replaces disc NTB10-125b / ITB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-800-347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
For 2011 Models refer to 2011 Models - Installing the Navigation Update
2010 Models - Installing the Navigation Update
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function, otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
For 2010 models there are three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program
C. Check Bluetooth(R) Setting
A: Disable Bluetooth(R) Function
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 524
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program -2010 Models
NOTE:
For 2011 Models, refer to 2011 Models - Installing the Navigation Update.
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 525
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No.1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD / DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB10-068 (Disc 1/3) into the in-dash CD/DVD player.
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 526
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 527
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
^ If "Now preparing loading shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 528
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the reprogram has finished loading:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 529
^ "Program loading is completed will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update - step 22.
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 530
23. "Rewriting boot data" (Figure 20) and "Rewriting program data" (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 531
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting - 2010 Models
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 532
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
2011 Models - Installing the Navigation Update
NOTE:
This procedure will take 10 - 15 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set
to a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral (parking brake ON).
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
5. Load the new disc "NTB12-070/1TB12-054 Re-programming Software DVD into the CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 533
^ If "Now preparing loading shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on screen Caution during the reprogram.
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 534
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the program has finished loading:
^ "Program loading is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update - step 9.
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 535
10. "Rewriting boot data and "Rewriting program data will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 back into the CD slot again.
One of the following screens will display:
^ If Figure A11 is displayed, it indicates that the re-program has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 536
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 5 through 12 again.
13. Eject the DVD.
14. Turn the ignition OFF. Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 537
Friday, June 14, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-017 Date: 100201
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-017 Date: 100201
Instruments - Fuel Gauge Issues/DTC's P0461/P0462/P0463
Classification:
EL09-030
Reference:
NTB10-017
Date:
February 1, 2010
ALTIMA AND MAXIMA; FUEL GAUGE ISSUES
AND/OR DTC P04611 P0462 / P0463
APPLIED VEHICLES:
2007-2010 Altima (L32)
2008-2010 Altima Coupe (CL32)
2008-2010 Altima Hybrid (L32HV)
2009-2010 Maxima (A35)
IF YOU CONFIRM:
The fuel gauge is erratic, inaccurate, or inoperative
And / Or
The MIL is "ON with DIG P0461, P0462, or P0463 stored in Self-Diagnosis.
ACTION:
Replace the fuel level sensor unit.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 394
^ Refer to the SERVICE PROCEDURE section of this bulletin for repair procedure.
^ Use the parts listed in the PARTS INFORMATION section in this bulletin.
NOTE:
Do not replace the entire fuel pump module assembly for this incident, if it should occur.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Failed Part (PP) line claim using the claims coding shown.
NOTE:
Version 1 fuel pump module assembly fits on earlier model year Altima models. Version 2 fits on later Altima and all Maxima models.
SERVICE PROCEDURE
1. Remove the fuel pump module assembly (module).
^ Refer to the appropriate section of the Electronic Service Manual (ESM), if needed.
NOTE:
Perform repairs in a clean work environment.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 395
2. Determine which version module you are working on (see Version 1 and 2).
3. Remove the 3 wire terminals with red, white, and double-wire black wires from under the top of the module as shown in Figure 1.
NOTE:
The white wire may appear yellowish in color.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 396
^ Press the tab in and gently pull the wire off its terminal (see Figure 2)
4. Remove the plastic tie strap that holds the wires to the fuel supply hose (supply hose) as shown in Figure 3.
CAUTION:
Be careful not to damage the supply hose or wiring when removing the tie strap.
5. Remove the fuel tank temperature sensor (temp sensor) from its retention feature (see Figure 4).
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 397
6. Version 1: Remove the temp sensor wires from the retention feature (see Figure 5).
7. Version 2 only: Remove the temp sensor wires from both retention features (see Figure 6).
8. Version 1 only: Remove all wires from the retention feature on the module (see Figure 7).
NOTE:
This retention feature is not reused.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 398
9. Version 1 only: Remove the black plastic retainer (retainer) as shown in Figure 8.
^ Pry on the clip ends using a pocket screwdriver or suitable tool, one side at a time (see Figure 8).
10. Remove the level sensor from the module (see Figure 9).
Push the tab inward, and then push the level sensor up, and then pull it away from the module.
11. Install the new level sensor onto the module (no picture shown).
Perform Step 10 in reverse, making sure its tab locks into place.
12. Version 1 only: Reinstall the retainer by snapping it into place (see Figure 10).
^ Make sure the level sensor's wires are not pinched under the retainer.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 399
13. Install the temp sensor into its retention feature (see Figure 11).
14. Version 1 only: Install the temp sensors wiring into the retention feature as shown in Figure 12.
^ Route the temp sensor's wires to the right of the level sensor.
^ Make sure the wiring is clear of float arm movement.
^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.
15. Version 2 only: Secure the level sensors wires into the retention features (see Figure 13).
^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 400
16. Route the wires on the inside of the supply hose (see Figure 14).
17. Secure the wires to the supply hose with a tie strap as shown in Figure 14.
CAUTION:
Be careful not to damage the supply hose or wires when installing the tie strap.
^ Step 17 applies to both module versions.
NOTE:
Tie straps are considered a shop supply.
18. Install the wires to the correct terminals (see Figure 15 below).
^ Make sure the wires are routed correctly as shown in Figure 15.
--> Red and white wires are routed in front of the blue wire.
--> The double black wire is in between the blue and single black wires.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 401
^ Make sure the tabs are securely locked.
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 04-049H Date: 110413
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 04-049H Date: 110413
Electrical - Trailer Light Wiring Info.
Classification: EL03-043H
Reference: NTB04-049H
Date: April 13, 2011
TRAILER LIGHT WIRING
This bulletin has been amended. The Applied Vehicles have been updated. Please discard previous versions of this is bulletin.
APPLIED VEHICLES
SERVICE INFORMATION
NOTE:
This bulletin provides information to be shared with all affected customers.
^ This TSB contains the appropriate hookup points for connecting a trailer light wiring harness to the towing vehicle's electrical system.
^ The wiring diagrams contained in this bulletin are for Nissan vehicles that have trailer towing capability (see the owners manual) but do not have a
Genuine Nissan accessory towing kit (with wiring) available.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 318
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 319
^ When splicing into the vehicle electrical system, a power-type module/converter must be used to provide power for all trailer lighting. A
power-type module/converter uses the vehicle battery as a direct power source for all trailer lights while using the vehicle taillight, stoplight, and
turn signal circuits only as a signal source. (See the illustration above.) The module/converter must draw no more than 5 milliamps from the
vehicle turn signal circuits and no more than 15 milliamps from the stop and tail light circuits.
CAUTION:
Using a module/converter that exceeds these power requirements listed above may negatively affect the performance and function of the vehicle's
electrical system.
See a professional trailer dealer or trailer rental agency for installation of the proper equipment.
Customers who inquire about towing should be reminded of the following:
^ Always check for correct operation of the turn signals, stoplights, and taillights every time a trailer is hitched up for towing.
^ The towing capacity for 350Z (Coupe Only), Altima, Maxima, and Sentra is 1,000 lbs.
For more information, refer customers to the Owner's Manual as well as the Nissan Towing Guide, available online at NissanUSA.com.
Thursday, June 13, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
Interior - Door Panel Looks Faded/Discolored
Classification: BT08-031B
Reference: NTB08-090B
Date: April 26, 2011
ALTIMA AND MAXIMA; DOOR PANEL LOOKS DISCOLORED / FADED
This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard all previous versions.
APPLIED VEHICLES:
2007-2011 Altima Coupe, Sedan, and Hybrid (C/L32/HV)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 312
2009-0211 Maxima (A35)
SERVICE INFORMATION
If a door panel looks discolored or faded as shown in Figure 1:
^ The probable cause is dirt buildup in the grain of the material. See below for details on how to clean the door panel.
NOTE:
^ Vehicle care and maintenance (cleaning) is not covered under warranty.
^ DO NOT replace the door panel when cleaning will solve the incident.
A soiled door panel can be cleaned as follows:
^ Following the instructions on the label, apply Nissan Vinyl and Leather Cleaner to the door panel surface.
^ Gently use a soft bristle brush to remove trapped dirt.
^ Spray the area with water.
^ Wipe the area clean using a clean cloth.
^ Repeat the cleaning procedure as needed.
After treating the soiled area, the door panel should be clean as shown in Figure 2.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 313
Wednesday, June 12, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
Computers/Controls - CONSULT(R) Reprogramming Info.
Classification: EC11-021A
Reference: NTB11-074A
Date: August 18, 2011
REPROGRAMMING WITH CONSULT
This bulletin has been amended. The statements below have changed. No other changes have been made. Please discard any previous copies.
APPLIED VEHICLES: All Nissan vehicles with a reprogrammable ECU
SERVICE INFORMATION
If you have a reprogram that requires the use of CONSULT-IT (C-II, and C-II is not available:
^ Refer to the chart below to determine CONSULT applicability.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 477
CURRENT REPROGRAMMING APPLICABILITY CHART
Reprogramming C-II Loaner Program
(Available ONLY for reprogramming use)
^ Contact TECH LINE and they will determine if a C-II Loaner is needed. If so they will make arrangements for the loaner to be shipped.
^ Dealerships must return the C-II Loaner immediately after the reprogramming is completed.
^ If the Loaner is not returned within one week of delivery, your FOM will be contacted to collect the unit.
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-141 Date: 091208
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-141 Date: 091208
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 355
Engine - Reman Engine Start Up Lubrication Information
Classification: EM09-010
Reference: NTB09-141
Date: December 8, 2009
REMANUFACTURED ENGINE LUBRICATION UPON INITIAL START UP
APPLIED VEHICLE: All Nissan vehicles having a remanufactured engine installed
SERVICE INFORMATION
During remanufactured engine storage, upper engine lubrication may dissipate/disperse. Camshaft scoring or seizure may occur at initial start up
unless the procedure below is followed.
1. Refer to the MA section of the applicable Electronic Service Manual (ESM) to determine the specified volume of oil required to fill both the
crankcase and filter.
2. Set one (1) quart of oil aside and fill the crankcase with the remaining quantity (one quart should remain unused).
3. Prior to initial engine start up, pour the one (1) remaining quart of oil into the valve cover.
^ It is recommended to quickly squeeze the quart of oil out of the container to "flood" the camshafts and cam bearings.
4. Immediately start the engine while the upper end is "flooded" with oil.
Tuesday, June 11, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
Emissions - System Readiness Test (SRT) Drive Patterns
Classification: EC98-001F
Reference: NTB98-018F
Date: November 7, 2012
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
This bulletin has been amended. Several Changes were made at "Step 7: Confirm All SRTs "COMPLETE"". Please discard all previous versions of
this bulletin.
APPLIED VEHICLES: 1996 and newer Model Years as required by State Emissions Inspections Regulations.
SERVICE INFORMATION
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be
checked.
^ The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components.
^ In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed.
The State Emissions Inspection Station may advise a Nissan customer to return to the dealership for service due to one or more SRT items coming
up "INCOMPLETE." Use the information in this Bulletin to help you "COMPLETE" the SRT.
^ In most cases the ECM will automatically complete its self diagnosis cycle during normal vehicle usage, and the SRT status will indicate
"COMPLETE" for each applicable system.
^ Once indicating "COMPLETE", the SRT status remains "COMPLETE" until the Self Diagnosis memory is erased.
^ Occasionally, certain portions of the self diagnostic test may not be completed as a result of the customer's normal driving pattern. In these cases
the SRT will indicate "INCOMPLETE" for these items.
NOTE: The SRT will also indicate "INCOMPLETE" if:
^ The self diagnosis memory is erased for any reason, or The ECM memory power supply is interrupted for several hours.
This bulletin contains information to help you perform a comprehensive road test (Drive Pattern) that enables the ECM to complete the SRT.
^ A separate Drive Pattern sheet for each 1996 and 1997 vehicle variation is included with this Bulletin.
^ For 1998 and newer vehicles, refer to the EC section of the appropriate Service Manual for the required Drive Pattern. They are listed under On
Board Diagnostic> System Readiness Test.
NOTE:
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced (i.e. model, model year, engine,
emissions certification, transmission, powertrain, and for 1996/1997 models, ECM part number.
NOTE:
To ensure all ECM Self Test requirements are met, it is important to drive the entire Drive Pattern even if only one SRT item indicates
"INCOMPLETE."
CLAIMS INFORMATION:
Refer to the current Warranty Flat Rate Manual for claims information.
Service Procedure
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 2
SRT WORKFLOW
Step 1: Check for DTC
1. Use a CONSULT tool to check for any stored DTCs.
^ If any DTCs are stored they must be repaired at this time.
^ Refer to ASIST for diagnostic and repair information.
NOTE:
Normal warranty coverage will apply for DTC repairs.
2. If no DTCs are stored, go to the next step.
NOTE:
DO NOT touch "Erase" or you will lose previously completed SRTs.
Step 2: Check SRT Status
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 3
Check the SRT Status (Complete or Incomplete).
^ Use the appropriate CONSULT tool.
^ For older vehicles, a Generic Scan Tool may be needed to check SRT status.
NOTE:
In some cases, the normal driving that occurs between the time the vehicle was referred by the State Emissions Inspection Station and it is
brought into the dealership for SRT evaluation may allow the ECM to complete the SRTs. If this occurs, no further action is necessary.
Always check SRT status before performing the SRT Drive Pattern.
Step 3: Identify the Vehicle
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced refer to the information below in
the image:
Step 4: Obtain ECM Part Number (1996 and 1997 models only)
1. Use a CONSULT tool to obtain the ECM part number.
2. Write the ECM part number in the space provided above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 4
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 5
3. Compare the vehicles ECM part number with the list of ECM part numbers provided in the Nissan SRT System Chart above to determine the
Drive Pattern for the vehicle being inspected.
NOTE:
For 1996 and 1997 models; if the vehicles ECM part number does not match a part number listed on the SRT System Chart for that
vehicle, either 1) the vehicle was identified incorrectly or 2) the vehicle has the wrong ECM installed. The SRT cannot be completed with
the incorrect ECM.
Step 5: SRT Road Test (perform Drive Pattern)
To properly obtain SRT readings of "COMPLETE" it is necessary to drive the vehicle under the exact conditions required by the vehicle's
ECM.
Be sure to select the correct Drive Pattern. The SRTs will not complete if the wrong drive pattern for that vehicle is used.
1. Select the Drive Pattern based on the Vehicle Identification (see Step 3).
^ For 1996 and 1997 vehicles:
> This bulletin contains a specific Driving Pattern for every 1996 and 1997 Nissan vehicle.
> Use the "Bookmark" on the left side of the ASIST screen to choose the correct model and year.
> Verify that the vehicle ECM P/N matches EXACTLY an ECM P/N listed on the Drive Pattern sheet you chose.
> Print the Drive Pattern to take with you.
^ For 1998 and newer vehicles, refer to the EC section in the appropriate Service Manual for the required Drive Pattern. It is listed under
On-Board Diagnostics> System Readiness Test.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 6
> Print the Drive Pattern to take with you.
2. Prior to driving the vehicle, review the Drive Pattern and prepare to complete it from start to finish:
^ Review the Pre-Check items listed on the drive pattern and ensure all conditions are met.
^ Determine the vehicle speeds required by the drive pattern.
^ Plan your route to minimize traffic and traffic signals that might interrupt the Drive Pattern tasks.
^ Review the Drive Pattern section(s) that must be restarted if you are interrupted.
^ Do not use the ASCD (cruise control) during any section of the Drive Pattern that contains the "No ASCD" symbol.
^ Some EVAP-equipped vehicles will require that fuel be added to the tank between the first and second trip. Be prepared to purchase fuel
or plan your route to accommodate this step.
^ For these EVAP-equipped vehicles, begin the road test with less than 1/2 tank of fuel. If the fuel level is greater than 1/2, more time may
be required to complete the EVAP sections of the Drive Pattern and you may not be able to add fuel as required.
3. Review the Drive Pattern for any input signals that need to be monitored during the drive.
If needed, Connect a CONSULT tool to the vehicle to monitor required signals.
NOTE:
^ Monitor the Fuel Temperature if the EVAP SRT is "INCOMPLETE". One part of the EVAP SRT diagnostic logic requires a 3锟斤拷C
increase in fuel temperature from the time the ignition key is turned to "ON" as part of the test criteria. Fluctuations in the fuel
temperature reading can extend the time required for the EVAP SRT to indicate "COMPLETE". If the fuel temperature change is not
sufficient after completing the SRT Drive pattern, idle the vehicle until a fuel temperature increase of at least 3锟斤拷C is noted or until the
EVAP SRT indicates "COMPLETE".
^ If the fuel temperature increases 3锟斤拷C or more but the SRT still indicates "INCOMPLETE", the SRT Drive Pattern may need to be
repeated.
4. Note the following items before starting the Drive Pattern:
^ IMPORTANT:
Nissan requires using a driver and an assistant to conduct SRT driving patterns. The assistant should read the Drive Pattern, CONSULT
data, and drive time and convey driving instruction to the driver. It is the driver's responsibility to observe and react to traffic conditions.
Always drive the vehicle in a safe manner and obey all traffic laws.
^ To ensure all ECM Self Test requirements are met, drive the ENTIRE pattern whenever any SRT items indicate "INCOMPLETE".
^ Some vehicles require that sections of the Drive Pattern be driven two times to satisfy the "self diagnosis two trip logic". For vehicles
that require two trips, the pre-check engine coolant temperature must be met before beginning Section 1 of the second trip.
5. Perform the Drive Pattern:
a. Make sure all Pre-Check conditions are met.
b. Drive the vehicle and carefully follow the specific instructions and time requirements listed in each section of the Drive Pattern.
NOTE: If you monitor the (B/FUEL SCHDL):
^ The Base Fuel Schedule (B/FUEL SCHDL) is an indication of engine load.
^ It will be easier to match high B/FUEL SCHDL values when driving up slight hills in the recommended gear range.
^ It will be easier to match low B/FUEL SCHDL values when driving down slight hills in the recommended gear range.
^ Turning the A/C compressor ON will increase the B/FUEL SCHDL value, while turning it OFF will decrease the B/FUEL SCHDL
value.
Step 6: Recheck for DTC
Upon completion of the Drive Pattern, determine if any DTCs have been stored. Only in rare cases will this occur.
^ If a DTC has been stored after completing the Drive Pattern, it must be repaired. Refer to ASIST for diagnostic and repair information.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 7
NOTE:
Normal warranty coverage will apply for DTC repairs.
^ Once the DTC is repaired, erase the stored DTC. Turn the ignition OFF for 10 seconds, and then repeat the entire Drive Pattern (Step
5) to "COMPLETE" the SRTs.
^ If no DTCs have been stored, DO NOT touch "Erase" or all SRT items will reset to "INCOMPLETE".
Step 7: Confirm All SRTs "COMPLETE"
If all SRT items indicate "COMPLETE", the inspection is complete.
^ If Catalyst and/or 02 Sensor Monitors show "INCOMPLETE" perform step A or B below.
A. Check Self Learning Value and A/F ALPHA. If either value is +10% or more above target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0171 or P0174 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
A. Check Self Learning Value and A/F ALPHA. If either value is -10% or more below target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0172 or P0175 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
^ After repairs have been made, run the prescribed drive pattern and check that A/F ALPHA is within +/- 10% of the target of 100%
during the steady state portions of the drive cycle. If it is not, then continue repairs. If it is, return to STEP 5.
System Readiness Test Drive Patterns
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 8
SRT DRIVE PATTERN LAYOUT
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 9
Pattern # 1 - 96 Altima (FED) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 10
Pattern # 2 - 96 Altima (FED) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 11
Pattern # 3 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 12
Pattern # 4 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 13
Pattern # 5 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 14
Pattern # 6 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 15
Pattern # 7 - 97 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 16
Pattern # 8 - 97 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 17
Pattern # 9 - 97.5 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 18
Pattern # 10 - 97.5 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 19
Pattern # 11 - 96 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 20
Pattern # 12 - 96 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 21
Pattern # 13 - 97 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 22
Pattern # 14 - 97 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 23
Pattern # 15 - 96 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 24
Pattern # 16 - 96 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 25
Pattern # 17 - 97 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 26
Pattern # 18 - 97 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 27
Pattern # 19 - 96 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 28
Pattern # 20 - 97 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 29
Pattern # 21 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 30
Pattern # 22 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 31
Pattern # 23 - 96 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 32
Pattern # 24 - 97 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 33
Pattern # 25 - 97 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 34
Pattern # 26 - 96-97 200SX (SR20DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 35
Pattern # 27 - 96-97 200SX (SR20DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 36
Pattern # 28 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 37
Pattern # 29 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 38
Pattern # 30 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 39
Pattern # 31 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 40
Pattern # 32 - 97 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 41
Pattern # 33 - 97 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 42
Pattern # 34 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 43
Pattern # 35 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 44
Pattern # 36 - 97 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 45
Pattern # 37 - 96 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 46
Pattern # 38 - 96 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 47
Pattern # 39 - 97 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 48
Pattern # 40 - 97 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 49
Pattern # 41 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 50
Pattern # 42 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 51
Pattern # 43 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 52
Pattern # 44 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 53
Pattern # 45 - 96 300ZX (Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 54
Pattern # 46 - 96 300ZX (Turbo) A/T
Monday, June 10, 2019
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-114B Date: 120614
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-114B Date: 120614
Tire Monitor System - Tire Inflation Information
Classification: WT 10-005B
Reference: NTB10-0114B
Date: June 14, 2012
INFLATING TIRES EQUIPPED WITH TPMS
The publication date on this bulletin has been amended to include the newest models.
APPLIED VEHICLE: All Nissan with Tire Pressure Monitor System (TPMS)
SERVICE INFORMATION
Improper use of tire inflator tools can break the stem of a Tire Pressure Monitor System (TPMS) sensor.
NOTE:
The type of stem breakage shown in Figure 1 is not considered a warrantable repair.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 120
Please refer to the following examples of recommended and not recommended tire pressure filling tools.
Not Recommended tire inflator tools.
Recommended tire inflating tools.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 121
Aftermarket Tire Sealers