2014 Nissan-Datsun Altima Diagrams. DTC # 09-111B Date: 100901

Interior - Driver's Seat Bottom Shifts/Rocks Slightly

Classification: BT09-057B

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 455

Reference: NTB09-111B

Date: September 1, 2010

2008-2010 ALTIMA COUPE; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY

This bulletin has been amended. Replacement of the seat side finisher has been added to the service procedure and the Parts Information has been

updated. Please discard previous versions.

APPLIED VEHICLES: 2008-2010 Altima Coupe (CL32) -equipped with power seat

APPLIED VIN:

2008-2009 vehicles - All

2010 vehicles built before 1N4(*)L2E(**)A(*) 117207

APPLIED DATE: Vehicles built on or before November 18, 2009

IF YOU CONFIRM:

The driver seat bottom (power seat only) very slightly "rocks" and/or "shifts" back and forth when accelerating, braking, or when making a turn.

ACTION:

Replace the driver seat cushion frame assembly (adjuster assembly) with a new one.

^ During reassembly use a new side seat finisher.

IMPORTANT:

The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 456

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down all radio station pre-sets.

2. If equipped - write down / record the following customer settings for the ATC (Automatic Temperature Control) system. (Refer to the Service

Manual as needed):

^ Temperature Setting Trimmer

^ Foot Position Setting Trimmer

^ Inlet Port Memory Function

3. Turn the ignition switch OFF.

4. Disconnect both battery cables - negative cable first.

5. WARNING: Wait for at least 3 minutes before removing the driver seat.

6. Carefully remove the driver seat from the vehicle.

^ Refer to the Service Manual section SE for seat removal procedure.

CAUTION:

Use covers as needed to protect interior surfaces from being scratched or damaged.

7. Replace the cushion frame assembly (adjuster assembly).

^ Refer to the 2010 Altima Coupe Service Manual - SE Section, Front Seat Driver Side: Disassembly and Assembly.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 457

^ During reassembly use a new side finisher listed in the Parts Information.

NOTE:

This bulletin contains additional helpful information for Seatback Finisher Removal (See below).

8. Connect the battery cables - positive cable first.

9. Reset the clock and the radio station presets.

10. Refer to the Service Manual for the following "reset / relearn procedures:

^ Power Window Initialization

^ Sunroof Memory Reset/Initialization

^ ATC Temperature Setting Trimmer (A/C system)

^ ATC Foot Position Setting Trimmer (A/C system)

^ ATC Inlet Port Memory Function - FRE and REC (A/C system)

^ Rear View Monitor Possible Route Line Center Position Adjustment (if equipped)

^ Steering Angle Sensor Neutral Position

11. Inform the customer they will need to "reset" their Automatic Drive Positioner.

Seatback Finisher Removal

1. Move / adjust the seat bottom and seat back to the full forward positions.

NOTE:

The seat back finisher is held on with:

^ 2 top hooks

^ 2 side clips

^ 2 bottom clips

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 458

2. Reach under the seat and disconnect the 2 elastic straps for the toe flap.

3. Insert your fingers behind the bottom corner of the finisher.

4. Locate the bottom clip with your fingers.

5. Pull the finisher next to the clip to unsnap the clip.

6. Repeat 3, 4 and 5 for the other bottom clip.

7. Insert your fingers into the side of the finisher.

8. Locate the "side" clip.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 459

9. Support the finisher with the palm of your hand.

10. Pull the finisher next to the clip to unsnap the clip.

11. Repeat 7 to 10 for the other "side" clip.

12. Pull down on the finisher to remove it.

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...

NISSAN

Search This Blog