2017 Nissan-Datsun Altima Technical Service Bulletin # 10-033B Date: 120314

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-033B Date: 120314

Multi AV System - Configuration After Replacing Control Unit

Classification: EL10-008B

Reference: NTB10-033B

Date: March 14, 2012

AV CONTROL UNIT REPLACEMENT REQUIRES CONSULT-III PLUS CONFIGURATION

This bulletin has been amended. The Applied Vehicles and Service Procedure sections have been revised. Please discard previous versions.

APPLIED VEHICLES:2010-2012 370Z Coupe and Roadster (H/Z34)

2010-2012 Altima Coupe, Sedan, and Hybrid (C/L32/HV)

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 130

2011-2013 GT-R (R35)

2010-2012 Maxima (A35)

2011-2012 Murano and Murano Cross Cabriolet (E/Z51)

2011-2012 Quest (E52)

SERVICE INFORMATION

If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason follow the steps in the Service Procedure to configure the Multi

AV system.

NOTE:

The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control

Unit until instructed.

Service Procedure

Before starting, make sure your ASIST has been freshly synchronized and all CONSULT-III (C-III) plus upgrades have been installed.

Parts of the Procedure

PART 1:

Record Multi AV Configuration Values of Original AV Control Unit; Replace AV Control Unit

1. Make sure the shift selector is in Park, and the parking brake is set.

2. Connect the C-III plus VI to the vehicle.

3. Turn ON the ignition.

NOTE:

You may want to start the engine to keep the battery charged during this procedure.

4. Write down customers radio station presets. (Presets will be lost during this procedure.)

5. Launch CONSULT-III (C-III) plus on the CONSULT PC.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 131

6. Select Re/programming Configuration.

7. Read the General Precaution.

When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.

8. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.

9. Select, Select.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 132

10. Confirm the correct Model Name and Model Year are displayed.

When finished, select Confirm.

11. After system call completes, confirm the correct VIN is displayed.

When finished, select Confirm.

NOTE:

If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.

12. Select MULTI AV.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 133

13. Select Read/Write Configuration.

14. Select Before Replace ECU.

15. Confirm current configuration and write it down.

^ Configuration can also be printed with the Print Screen button or Screen Capture button.

NOTE:

Configurable options will differ between models. Your screen may look different.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 134

16. Select Save.

NOTE:

If the configuration data cannot be saved, replace the AV Control Unit as instructed in the applicable Electronic Service Manual (ESM) and then

proceed to PART 3: Perform Multi AV Initialization shown below in this bulletin.

17. Select End.

18. Replace the AV Control Unit as instructed in the applicable ESM.

PART 2:

Configure the Multi AV System

19. Perform steps 1-10.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 135

20. Select Confirm.

21. Select After Replace ECU.

22. Select OK.

After performing step 22

If an error message does not display:

^ Proceed to PART 5: Confirm Multi AV System Is Operational shown below in this bulletin.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 136

If an error message does display:

^ Proceed to PART 3: Perform Multi AV Initialization, below.

PART 3 (if needed):

Perform Multi AV Initialization

NOTE:

Leave C-III plus running and the VI connected while performing Multi-AV initialization.

23. Turn OFF the audio system.

24. Put the AV system into System Diagnostic Mode as follows:

a. Press and hold the SETTING button (see Figure 14).

b. While holding the SETTING button, turn the volume control knob 40 clicks or more.

^ The volume control knob can be turned either direction.

^ When the system goes into the System Diagnostic Menu, the screen in Figure 15 will display.

25. Select Confirmation/Adjustment.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 137

26. Select Delete Unit Connection Log.

27. Select Yes.

28. Select Initialize Settings.

29. Select Accessory Number Initialization.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 138

30. Select Yes.

31. Wait while the system initializes.

^ The screen in Figure 21 will display while initializing.

^ The screen in Figure 22 will display when initialization is complete.

32. Once initialization is complete, reboot the Multi AV system as follows:

a. Turn OFF the ignition.

b. Wait 10 seconds.

c. Turn ON the ignition.

Proceed to PART 4: Manually Configure the Multi AV System, below.

PART 4 (if needed):

Manually Configure the Multi AV System

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 139

NOTE:

If the screen in Figure 23 is not displayed, click on the Home icon.

33. Select Re/programming Configuration.

34. Read the General Precaution.

When finished, touch the "Confirmed instructions" box to insert a check mark, then select Next.

35. Select the Manual Selection (Vehicle Name) tab, then select the applicable Model and Year.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 140

36. Select, Select.

37. Confirm the correct Model Name and Model Year are displayed.

When finished, select Confirm.

38. Confirm the correct VIN is displayed.

When finished, select Confirm.

NOTE:

If the VIN displayed is incorrect, input the correct VIN. When finished, select Confirm.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 141

39. Select MULTI AV.

40. Select Manual Configuration.

41. Use the drop down menus to select the Configuration options that were printed or written down in step 15.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 142

^ Configurable options will differ between models. Your screen may look different from Figures 30 and 31.

42. Select Next.

43. Confirm the configuration displayed is correct, then select OK.

44. Start the engine and let it idle briefly.

45. Use C-III plus to clear any codes from the Multi AV system.

a. Select Diagnoses (One System)> Multi AV> Self Diagnosis Results.

b. Clear any codes that may be present.

46. Close C-III plus and disconnect the VI from the vehicle.

PART 5:

Confirm Multi AV System Is Operational

47. Put your toot on the brake, start the engine, and move the shift selector to R (reverse).

48. If equipped, make sure the rear view monitor is working correctly.

49. Put the shift selector back into Park.

50. Turn ON the radio.

51. Turn the volume knob and make sure the audio volume responds to movement of the knob.