Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # NHTSA10V401000 Date: 100903

2017 Nissan-Datsun Altima Technical Service Bulletin # NHTSA10V401000 Date: 100903



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 464



Recall 10V401000: Potential GPS Battery Fires



VEHICLE MAKE/MODEL: MODEL YEAR(S):





Nissan/Altima 2008-2010



Nissan/Frontier 2008-2010



Nissan/Pathfinder 2008-2010



Nissan/Rogue 2008-2010



Nissan/Sentra 2008-2010



Nissan/Versa 2008-2010



Nissan/XTerra 2008-2010



MANUFACTURER: Nissan North America, Inc.



MFR'S REPORT DATE: September 03, 2010



NHTSA CAMPAIGN ID NUMBER: 10V401000



NHTSA ACTION NUMBER: N/A



COMPONENT: Equipment: Electrical: Navigational System (Global Positioning System)



POTENTIAL NUMBER OF UNITS AFFECTED: ?



SUMMARY:



Nissan is recalling certain vehicles that were equipped with a Garmin Nuvi Model 750 navigation system. The batteries contained in the affected



GPS units can overheat.



CONSEQUENCE:



Overheated batteries could result in a fire.



REMEDY:



Nissan will notify owners and the repairs will be performed by Garmin technicians by replacing the battery and inserting a spacer on top of the



battery free of charge. The safety recall is expected to begin during September 2010. Owners may contact Garmin directly at 1-866-957-1981 or



Nissan at 1-800-647-7261.



NOTES:



Owners may also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153),

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more