Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 04-049H Date: 110413

2017 Nissan-Datsun Altima Technical Service Bulletin # 04-049H Date: 110413



Electrical - Trailer Light Wiring Info.



Classification: EL03-043H



Reference: NTB04-049H



Date: April 13, 2011



TRAILER LIGHT WIRING



This bulletin has been amended. The Applied Vehicles have been updated. Please discard previous versions of this is bulletin.



APPLIED VEHICLES



SERVICE INFORMATION



NOTE:



This bulletin provides information to be shared with all affected customers.



^ This TSB contains the appropriate hookup points for connecting a trailer light wiring harness to the towing vehicle's electrical system.



^ The wiring diagrams contained in this bulletin are for Nissan vehicles that have trailer towing capability (see the owners manual) but do not have a



Genuine Nissan accessory towing kit (with wiring) available.



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 318



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 319



^ When splicing into the vehicle electrical system, a power-type module/converter must be used to provide power for all trailer lighting. A



power-type module/converter uses the vehicle battery as a direct power source for all trailer lights while using the vehicle taillight, stoplight, and



turn signal circuits only as a signal source. (See the illustration above.) The module/converter must draw no more than 5 milliamps from the



vehicle turn signal circuits and no more than 15 milliamps from the stop and tail light circuits.



CAUTION:



Using a module/converter that exceeds these power requirements listed above may negatively affect the performance and function of the vehicle's



electrical system.



See a professional trailer dealer or trailer rental agency for installation of the proper equipment.



Customers who inquire about towing should be reminded of the following:



^ Always check for correct operation of the turn signals, stoplights, and taillights every time a trailer is hitched up for towing.



^ The towing capacity for 350Z (Coupe Only), Altima, Maxima, and Sentra is 1,000 lbs.



For more information, refer customers to the Owner's Manual as well as the Nissan Towing Guide, available online at NissanUSA.com.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more