Tuesday, June 18, 2019
Monday, June 17, 2019
Sunday, June 16, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
Engine - Oil Leakage From The Upper End Of Oil Cooler
Classification:
EM10-002b
Reference:
NTB11-015b
Date:
February 1, 2013
ALTIMA SEDAN AND COUPE, SENTRA, AND ROGUE WITH QR25DE ENGINE; OIL LEAK
This bulletin has been amended in APPLIED VEHICLES, SERVICE PROCEDURE, PARTS INFORMATION, and CLAIMS INFORMATION.
Discard all previous versions of this bulletin.
APPLIED VEHICLES:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 488
2007 - 2012 Altima Sedan (L32)
2008 - 2013 Altima Coupe (CL32)
2007-2012 Sentra (B16)
2008 - 2013 Rogue (535)
APPLIED ENGINE:
QR25DE (4 cyl)
IF YOU CONFIRM:
Oil is leaking from the upper end of the engine oil cooler (oil cooler). See Figure 1.
ACTION:
Reseal the oil cooler with the parts listed in the PARTS INFORMATION.
^ For repairs refer to SERVICE PROCEDURE.
NOTE:
Do not replace the complete engine oil cooler assembly for this incident if it should occur.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 489
CLAIMS INFORMATION
SERVICE PROCEDURE
1. Remove the oil cooler from the engine block.
^ Refer to the appropriate section of the Electronic Service Manual (ESM) if needed.
^ Perform repairs in a clean work environment.
2. Remove the four (4) bolts, and then remove the upper half of the oil cooler. See Figure 2.
3. Remove the O-ring gasket, and then thoroughly clean out the gasket area and around it with a suitable cleaner.
^ The dashed line in Figure 3 shows the O-ring gasket area to be cleaned.
^ Make sure no debris or contaminants get into the holes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 490
^ Also clean underneath the upper half of the oil cooler (no picture shown).
4. Lightly coat the new O-ring gasket (see PARTS INFORMATION) with engine oil, and then put it in place. See Figure 4.
5. Install the upper half of the oil cooler with the bolts.
6. Torque the bolts in two steps: first step at half value, and then the second step at full value (listed below).
^ Bolts torque sequence:
1-2-3-4-5-6-7-8 (see Figure 5).
^ Bolts torque:
4.0 N.m (0.41 kg-m, 35.4 in lb)
7. Install the oil cooler to the engine with a new gasket (see PARTS INFORMATION).
Refer to the appropriate section of the ESM if needed.
Saturday, June 15, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
Campaign P1234 - Navigation Software Update For Various Issues
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 522
Reference:
NTB11-073a
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN CALL WAITING FUNCTION NAVIGATION UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
CAMPAIGN ID #: P1234
APPLIED VEHICLES:
2010-2011 Altima Sedan, Coupe, and Hybrid (L32, CL32, & L32HV)
2010-2011 Maxima (A35)
2010 - 2011 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, iPod(R), and voice recognition functions may not be working as intended. To
remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or
labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system.
IDENTIFICATION NUMBER
Nissan has assigned identification number P1234 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for 2010 models in this campaign.
^ Do not use disc 3/3.
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 523
^ This disc also replaces disc NTB10-125b / ITB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-800-347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
For 2011 Models refer to 2011 Models - Installing the Navigation Update
2010 Models - Installing the Navigation Update
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function, otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
For 2010 models there are three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program
C. Check Bluetooth(R) Setting
A: Disable Bluetooth(R) Function
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 524
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program -2010 Models
NOTE:
For 2011 Models, refer to 2011 Models - Installing the Navigation Update.
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 525
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No.1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD / DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB10-068 (Disc 1/3) into the in-dash CD/DVD player.
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 526
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 527
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
^ If "Now preparing loading shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 528
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the reprogram has finished loading:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 529
^ "Program loading is completed will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update - step 22.
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 530
23. "Rewriting boot data" (Figure 20) and "Rewriting program data" (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 531
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting - 2010 Models
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 532
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
2011 Models - Installing the Navigation Update
NOTE:
This procedure will take 10 - 15 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set
to a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral (parking brake ON).
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
5. Load the new disc "NTB12-070/1TB12-054 Re-programming Software DVD into the CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 533
^ If "Now preparing loading shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on screen Caution during the reprogram.
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 534
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the program has finished loading:
^ "Program loading is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update - step 9.
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 535
10. "Rewriting boot data and "Rewriting program data will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 back into the CD slot again.
One of the following screens will display:
^ If Figure A11 is displayed, it indicates that the re-program has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 536
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 5 through 12 again.
13. Eject the DVD.
14. Turn the ignition OFF. Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 537
Thursday, June 13, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
Interior - Door Panel Looks Faded/Discolored
Classification: BT08-031B
Reference: NTB08-090B
Date: April 26, 2011
ALTIMA AND MAXIMA; DOOR PANEL LOOKS DISCOLORED / FADED
This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard all previous versions.
APPLIED VEHICLES:
2007-2011 Altima Coupe, Sedan, and Hybrid (C/L32/HV)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 312
2009-0211 Maxima (A35)
SERVICE INFORMATION
If a door panel looks discolored or faded as shown in Figure 1:
^ The probable cause is dirt buildup in the grain of the material. See below for details on how to clean the door panel.
NOTE:
^ Vehicle care and maintenance (cleaning) is not covered under warranty.
^ DO NOT replace the door panel when cleaning will solve the incident.
A soiled door panel can be cleaned as follows:
^ Following the instructions on the label, apply Nissan Vinyl and Leather Cleaner to the door panel surface.
^ Gently use a soft bristle brush to remove trapped dirt.
^ Spray the area with water.
^ Wipe the area clean using a clean cloth.
^ Repeat the cleaning procedure as needed.
After treating the soiled area, the door panel should be clean as shown in Figure 2.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 313
Wednesday, June 12, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
Computers/Controls - CONSULT(R) Reprogramming Info.
Classification: EC11-021A
Reference: NTB11-074A
Date: August 18, 2011
REPROGRAMMING WITH CONSULT
This bulletin has been amended. The statements below have changed. No other changes have been made. Please discard any previous copies.
APPLIED VEHICLES: All Nissan vehicles with a reprogrammable ECU
SERVICE INFORMATION
If you have a reprogram that requires the use of CONSULT-IT (C-II, and C-II is not available:
^ Refer to the chart below to determine CONSULT applicability.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 477
CURRENT REPROGRAMMING APPLICABILITY CHART
Reprogramming C-II Loaner Program
(Available ONLY for reprogramming use)
^ Contact TECH LINE and they will determine if a C-II Loaner is needed. If so they will make arrangements for the loaner to be shipped.
^ Dealerships must return the C-II Loaner immediately after the reprogramming is completed.
^ If the Loaner is not returned within one week of delivery, your FOM will be contacted to collect the unit.
Tuesday, June 11, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
Emissions - System Readiness Test (SRT) Drive Patterns
Classification: EC98-001F
Reference: NTB98-018F
Date: November 7, 2012
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
This bulletin has been amended. Several Changes were made at "Step 7: Confirm All SRTs "COMPLETE"". Please discard all previous versions of
this bulletin.
APPLIED VEHICLES: 1996 and newer Model Years as required by State Emissions Inspections Regulations.
SERVICE INFORMATION
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be
checked.
^ The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components.
^ In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed.
The State Emissions Inspection Station may advise a Nissan customer to return to the dealership for service due to one or more SRT items coming
up "INCOMPLETE." Use the information in this Bulletin to help you "COMPLETE" the SRT.
^ In most cases the ECM will automatically complete its self diagnosis cycle during normal vehicle usage, and the SRT status will indicate
"COMPLETE" for each applicable system.
^ Once indicating "COMPLETE", the SRT status remains "COMPLETE" until the Self Diagnosis memory is erased.
^ Occasionally, certain portions of the self diagnostic test may not be completed as a result of the customer's normal driving pattern. In these cases
the SRT will indicate "INCOMPLETE" for these items.
NOTE: The SRT will also indicate "INCOMPLETE" if:
^ The self diagnosis memory is erased for any reason, or The ECM memory power supply is interrupted for several hours.
This bulletin contains information to help you perform a comprehensive road test (Drive Pattern) that enables the ECM to complete the SRT.
^ A separate Drive Pattern sheet for each 1996 and 1997 vehicle variation is included with this Bulletin.
^ For 1998 and newer vehicles, refer to the EC section of the appropriate Service Manual for the required Drive Pattern. They are listed under On
Board Diagnostic> System Readiness Test.
NOTE:
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced (i.e. model, model year, engine,
emissions certification, transmission, powertrain, and for 1996/1997 models, ECM part number.
NOTE:
To ensure all ECM Self Test requirements are met, it is important to drive the entire Drive Pattern even if only one SRT item indicates
"INCOMPLETE."
CLAIMS INFORMATION:
Refer to the current Warranty Flat Rate Manual for claims information.
Service Procedure
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 2
SRT WORKFLOW
Step 1: Check for DTC
1. Use a CONSULT tool to check for any stored DTCs.
^ If any DTCs are stored they must be repaired at this time.
^ Refer to ASIST for diagnostic and repair information.
NOTE:
Normal warranty coverage will apply for DTC repairs.
2. If no DTCs are stored, go to the next step.
NOTE:
DO NOT touch "Erase" or you will lose previously completed SRTs.
Step 2: Check SRT Status
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 3
Check the SRT Status (Complete or Incomplete).
^ Use the appropriate CONSULT tool.
^ For older vehicles, a Generic Scan Tool may be needed to check SRT status.
NOTE:
In some cases, the normal driving that occurs between the time the vehicle was referred by the State Emissions Inspection Station and it is
brought into the dealership for SRT evaluation may allow the ECM to complete the SRTs. If this occurs, no further action is necessary.
Always check SRT status before performing the SRT Drive Pattern.
Step 3: Identify the Vehicle
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced refer to the information below in
the image:
Step 4: Obtain ECM Part Number (1996 and 1997 models only)
1. Use a CONSULT tool to obtain the ECM part number.
2. Write the ECM part number in the space provided above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 4
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 5
3. Compare the vehicles ECM part number with the list of ECM part numbers provided in the Nissan SRT System Chart above to determine the
Drive Pattern for the vehicle being inspected.
NOTE:
For 1996 and 1997 models; if the vehicles ECM part number does not match a part number listed on the SRT System Chart for that
vehicle, either 1) the vehicle was identified incorrectly or 2) the vehicle has the wrong ECM installed. The SRT cannot be completed with
the incorrect ECM.
Step 5: SRT Road Test (perform Drive Pattern)
To properly obtain SRT readings of "COMPLETE" it is necessary to drive the vehicle under the exact conditions required by the vehicle's
ECM.
Be sure to select the correct Drive Pattern. The SRTs will not complete if the wrong drive pattern for that vehicle is used.
1. Select the Drive Pattern based on the Vehicle Identification (see Step 3).
^ For 1996 and 1997 vehicles:
> This bulletin contains a specific Driving Pattern for every 1996 and 1997 Nissan vehicle.
> Use the "Bookmark" on the left side of the ASIST screen to choose the correct model and year.
> Verify that the vehicle ECM P/N matches EXACTLY an ECM P/N listed on the Drive Pattern sheet you chose.
> Print the Drive Pattern to take with you.
^ For 1998 and newer vehicles, refer to the EC section in the appropriate Service Manual for the required Drive Pattern. It is listed under
On-Board Diagnostics> System Readiness Test.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 6
> Print the Drive Pattern to take with you.
2. Prior to driving the vehicle, review the Drive Pattern and prepare to complete it from start to finish:
^ Review the Pre-Check items listed on the drive pattern and ensure all conditions are met.
^ Determine the vehicle speeds required by the drive pattern.
^ Plan your route to minimize traffic and traffic signals that might interrupt the Drive Pattern tasks.
^ Review the Drive Pattern section(s) that must be restarted if you are interrupted.
^ Do not use the ASCD (cruise control) during any section of the Drive Pattern that contains the "No ASCD" symbol.
^ Some EVAP-equipped vehicles will require that fuel be added to the tank between the first and second trip. Be prepared to purchase fuel
or plan your route to accommodate this step.
^ For these EVAP-equipped vehicles, begin the road test with less than 1/2 tank of fuel. If the fuel level is greater than 1/2, more time may
be required to complete the EVAP sections of the Drive Pattern and you may not be able to add fuel as required.
3. Review the Drive Pattern for any input signals that need to be monitored during the drive.
If needed, Connect a CONSULT tool to the vehicle to monitor required signals.
NOTE:
^ Monitor the Fuel Temperature if the EVAP SRT is "INCOMPLETE". One part of the EVAP SRT diagnostic logic requires a 3锟斤拷C
increase in fuel temperature from the time the ignition key is turned to "ON" as part of the test criteria. Fluctuations in the fuel
temperature reading can extend the time required for the EVAP SRT to indicate "COMPLETE". If the fuel temperature change is not
sufficient after completing the SRT Drive pattern, idle the vehicle until a fuel temperature increase of at least 3锟斤拷C is noted or until the
EVAP SRT indicates "COMPLETE".
^ If the fuel temperature increases 3锟斤拷C or more but the SRT still indicates "INCOMPLETE", the SRT Drive Pattern may need to be
repeated.
4. Note the following items before starting the Drive Pattern:
^ IMPORTANT:
Nissan requires using a driver and an assistant to conduct SRT driving patterns. The assistant should read the Drive Pattern, CONSULT
data, and drive time and convey driving instruction to the driver. It is the driver's responsibility to observe and react to traffic conditions.
Always drive the vehicle in a safe manner and obey all traffic laws.
^ To ensure all ECM Self Test requirements are met, drive the ENTIRE pattern whenever any SRT items indicate "INCOMPLETE".
^ Some vehicles require that sections of the Drive Pattern be driven two times to satisfy the "self diagnosis two trip logic". For vehicles
that require two trips, the pre-check engine coolant temperature must be met before beginning Section 1 of the second trip.
5. Perform the Drive Pattern:
a. Make sure all Pre-Check conditions are met.
b. Drive the vehicle and carefully follow the specific instructions and time requirements listed in each section of the Drive Pattern.
NOTE: If you monitor the (B/FUEL SCHDL):
^ The Base Fuel Schedule (B/FUEL SCHDL) is an indication of engine load.
^ It will be easier to match high B/FUEL SCHDL values when driving up slight hills in the recommended gear range.
^ It will be easier to match low B/FUEL SCHDL values when driving down slight hills in the recommended gear range.
^ Turning the A/C compressor ON will increase the B/FUEL SCHDL value, while turning it OFF will decrease the B/FUEL SCHDL
value.
Step 6: Recheck for DTC
Upon completion of the Drive Pattern, determine if any DTCs have been stored. Only in rare cases will this occur.
^ If a DTC has been stored after completing the Drive Pattern, it must be repaired. Refer to ASIST for diagnostic and repair information.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 7
NOTE:
Normal warranty coverage will apply for DTC repairs.
^ Once the DTC is repaired, erase the stored DTC. Turn the ignition OFF for 10 seconds, and then repeat the entire Drive Pattern (Step
5) to "COMPLETE" the SRTs.
^ If no DTCs have been stored, DO NOT touch "Erase" or all SRT items will reset to "INCOMPLETE".
Step 7: Confirm All SRTs "COMPLETE"
If all SRT items indicate "COMPLETE", the inspection is complete.
^ If Catalyst and/or 02 Sensor Monitors show "INCOMPLETE" perform step A or B below.
A. Check Self Learning Value and A/F ALPHA. If either value is +10% or more above target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0171 or P0174 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
A. Check Self Learning Value and A/F ALPHA. If either value is -10% or more below target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0172 or P0175 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
^ After repairs have been made, run the prescribed drive pattern and check that A/F ALPHA is within +/- 10% of the target of 100%
during the steady state portions of the drive cycle. If it is not, then continue repairs. If it is, return to STEP 5.
System Readiness Test Drive Patterns
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 8
SRT DRIVE PATTERN LAYOUT
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 9
Pattern # 1 - 96 Altima (FED) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 10
Pattern # 2 - 96 Altima (FED) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 11
Pattern # 3 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 12
Pattern # 4 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 13
Pattern # 5 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 14
Pattern # 6 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 15
Pattern # 7 - 97 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 16
Pattern # 8 - 97 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 17
Pattern # 9 - 97.5 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 18
Pattern # 10 - 97.5 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 19
Pattern # 11 - 96 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 20
Pattern # 12 - 96 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 21
Pattern # 13 - 97 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 22
Pattern # 14 - 97 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 23
Pattern # 15 - 96 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 24
Pattern # 16 - 96 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 25
Pattern # 17 - 97 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 26
Pattern # 18 - 97 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 27
Pattern # 19 - 96 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 28
Pattern # 20 - 97 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 29
Pattern # 21 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 30
Pattern # 22 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 31
Pattern # 23 - 96 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 32
Pattern # 24 - 97 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 33
Pattern # 25 - 97 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 34
Pattern # 26 - 96-97 200SX (SR20DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 35
Pattern # 27 - 96-97 200SX (SR20DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 36
Pattern # 28 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 37
Pattern # 29 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 38
Pattern # 30 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 39
Pattern # 31 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 40
Pattern # 32 - 97 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 41
Pattern # 33 - 97 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 42
Pattern # 34 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 43
Pattern # 35 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 44
Pattern # 36 - 97 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 45
Pattern # 37 - 96 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 46
Pattern # 38 - 96 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 47
Pattern # 39 - 97 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 48
Pattern # 40 - 97 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 49
Pattern # 41 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 50
Pattern # 42 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 51
Pattern # 43 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 52
Pattern # 44 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 53
Pattern # 45 - 96 300ZX (Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 54
Pattern # 46 - 96 300ZX (Turbo) A/T
Monday, June 10, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 09-040A Date: 100514
2014 Nissan-Datsun Altima Diagrams. DTC # 09-040A Date: 100514
Cooling System - Long Life Coolant Information
Classification: EM09-001A
Reference: NTB09-040A
Date: May 14, 2010
NEW BLUE NISSAN LONG LIFE ANTIFREEZE/COOLANT
This bulletin has been amended. The Service Information has been updated. Please discard previous versions of this bulletin.
SERVICE INFORMATION
In calendar year 2009, Nissan began filling some vehicles at the factory with a NEW Nissan Long Life Antifreeze/Coolant (LLC) that is blue in
color.
NOTE: LLC = Long Life Antifreeze/Coolant
The transition to this new Blue LLC continued though MY 2010. Beginning with MY 2011, all Nissan vehicles are filled at the factory with the Blue
LLC.
^ MY 2009 and 2010: Some vehicles are filled at the factory with Blue LLC.
^ MY 2011: All vehicles are filled at the factory with Blue LLC.
Blue LLC is designed to have a service life of 7 years/105,000 miles for the factory fill, and 5 years/75,000 miles for subsequent replacement fills.
Nissan Blue Super LLC is available through the Nissan Direct Ship Chemical Care Product Program, Website order link via dealer portal
www.NNAnet.com or order direct www.NissanChemicals.com.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 418
^ Blue LLC one gallon pre-diluted:
P/N 999MP - LP25500P
> The one gallon containers are pre-diluted with 50% antifreeze and 50% distilled water.
> Do not add additional water when using pre-diluted Blue LLC.
^ Blue LLC one quart concentrate:
P/N 999MP - L255QTP
> The one quart concentrate containers are intended for extreme cold weather application.
> Use the concentrate without mixing (do not add water).
> Add directly to the cooling system in specific amounts as directed on the container label.
Additional Information for using Blue LLC
Blue LLC and Green-colored Nissan LLC (P/N 999MP-AF000P) are compatible with each other:
^ Blue can be mixed/added with Green
^ Green can be mixed/added with Blue
CAUTION:
^ Adding Green LLC to Blue LLC will reduce/shorten the life expectancy of the Blue LLC to that of the Green LLC (4 years / 60,000 miles).
^ LLC must always be used with demineralized or distilled water, otherwise the life expectancy of the LLC (Blue or Green) will be degraded and
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 419
cooling system damage may occur.
Tuesday, June 4, 2019
Monday, June 3, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 09-003 Date: 090109
2014 Nissan-Datsun Altima Diagrams. DTC # 09-003 Date: 090109
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 219
iPod(R) - Charging With Nissan Interface System
Classification: EL08-037
Reference: NTB09-003
Date: January 9, 2009
iPod(R) Charging with Nissan Interface System for iPod(R)
APPLIED VEHICLES: All Nissan with Nissan Interface System for iPod(R)
(factory installed or accessory installed)
SERVICE INFORMATION
Please be aware that a recent design change was made by Apple to their iPod(R) and iPhone(R) products. As a result of this change, some customers
may report that their iPod(R)/iPhone(R) device does not charge while connected to the Nissan Interface System for iPod(R).
The Nissan Interface System for iPod(R) was designed to charge the customer's iPod(R) with a 12-volt power source, which has been supported by
all Apple iPod(R) and iPhone(R) devices until the latest generation. After Apple's design change, these new devices only support charging via a
5-volt source, which the Interface System does not provide. Customers may see error messages on the device screen, or notice that the device's
battery discharges while connected to their vehicle's interface system. Please note that while charging may not be supported playback and control
through the vehicle's audio system are still available.
Compatible Devices:
All Apple devices that support charging via a FireWire(R) connection are compatible with the Nissan Interface System for iPod(R). These include:
^ iPod(R) Classic - 1st through 6th generation
^ iPod(R) Mini - 1st through 2nd generation
^ iPod(R) Nano - 1st through 3rd generation
^ iPod(R) Touch - 1st generation
^ iPhone(R) - 1st generation
NOTE:
Refer to the vehicle Owner's Manual for further Nissan Interface System Information.
Non-compatible devices (as of 12/8/2008):
^ iPhone(R)3G
^ iPod(R) Nano - 4th generation
^ iPod(R) Touch - 2nd generation
Nissan is working closely with Apple to ensure full compatibility with our future Interface Systems, but as Apple's change was made without
adequate notification to Nissan, at this time there is no plan to modify the current Interface Systems for the 2009 model year.
Please make customers aware that there are products available in the aftermarket designed to reduce the 12V power source to 5V and should enable
their device to charge while connected to their vehicle. A few examples are provided below, however, Nissan expects these types of aftermarket
solutions to become even more widely available considering that Apple's change has impacted the charging ability of many automotive OEM's
iPod(R) integration systems.
Aftermarket Solutions:
PLEASE NOTE:
Nissan has not tested any of these aftermarket solutions and makes no endorsement, warranty, or guarantee of performance or compatibility for any
specific third party accessory. These devices are advertised by their respective manufacturers to resolve 12V to 5V charging issues, but have not
been designed for or tested with Nissan vehicles.
^ Scosche Passport - http://www.scosche.com/passport
^ Cablejive Charge Converter - http://cablejive.com/iphone_3g_charge_converter.html
^ Ridax Charge Converter - http://home.swipnet.se/ridax/connector.html?connipod.htm
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 220
Customer Service:
For further questions and comments, customers may always feel free to contact Nissan Consumer Affairs at 1-800-647-7261.
2014 Nissan-Datsun Altima Diagrams. DTC # 12-069 Date: 120820
2014 Nissan-Datsun Altima Diagrams. DTC # 12-069 Date: 120820
A/C - Does Not Cool Enough/Poor Performance
Classification: HA12-009
Reference: NTB12-069
Date: August 20, 2012
2007 - 2012 ALTIMA AND 2009 - 2012 MAXIMA;
A/C IS NOT COOLING / POOR PERFORMANCE
APPLIED VEHICLES: 2007 - 2012 Altima Sedan and Coupe (L32 / CL32)
2009 - 2012 Maxima (A35)
IF YOU CONFIRM
The A/C system is not cooling the cabin to factory specification,
and
The A/C compressor clutch is engaged,
and
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 85
The A/C system is fully charged,
and
The HVAC system doors and controls are working correctly.
ACTIONS
1. Check the A/C system pressures:
^ If the A/C system pressures are HIGH side low and LOW side low, go to step 2.
^ If the A/C pressures are any other then above, this bulletin does not apply. Refer to ASIST and the Service Manual for further diagnostic
information.
2. By feel, or with an infrared thermometer; check the temperature of the condenser / receiver dryer outlet tube.
^ Tube is Warm or Hot: This bulletin does not apply. Refer to ASIST and the Service Manual for further diagnostic information.
^ Tube is Cool or Cold: Replace the condenser and receiver dryer assembly.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE:
1. Check the A/C system pressures:
^ Refer to the appropriate Service Manual for system pressure specifications.
^ If the A/C system pressures are: HIGH side = low and LOW side = low, go to step 2 below.
^ If the A/C pressures are any other then above, this bulletin does not apply. Refer to ASIST and the Service Manual for further diagnostic
information.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 86
2. By feel, or with an infrared thermometer; check the temperature of the receiver dryer outlet tube.
^ Tube is Warm or Hot: This bulletin does not apply. Refer to ASIST and the Service Manual for further diagnostic information.
^ Tube is Cool or Cold: Replace the condenser and receiver dryer assembly.
Refer to the appropriate Service Manual for replacement information. Follow all Service Manual warnings and cautions as applicable.
NOTE:
^ Cool or Cold receiver dryer outlet tube indicates a blockage in the receiver dryer or condenser.
^ If desired, the filter can be removed from the receiver dryer to confirm the root cause of the issue was blockage (debris) in the receiver
dryer.
^ Figure 2 shows an example of a receiver dryer filter that is bowed and plugged with debris.
Saturday, June 1, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 10-009 Date: 100119
2014 Nissan-Datsun Altima Diagrams. DTC # 10-009 Date: 100119
Engine Controls - Seized O2 Sensor Removal Procedure
Classification: EM09-015
Reference: NTB10-009
Date: January 19, 2010
REMOVAL PROCEDURE FOR SEIZED EXHAUST SENSOR
APPLIED VEHICLES: All Nissan vehicles
SERVICE INFORMATION
If an exhaust sensor is seized in the exhaust manifold/catalyst/front tube, perform the procedure described in this bulletin to remove the sensor and
prevent unnecessary replacement of the exhaust manifold/catalyst/front tube.
In most cases this procedure is successful. This is because the threads of the exhaust sensors are made of a softer material than the part they thread
into on the exhaust manifold/catalyst/front tube.
NOTE:
The replacement of exhaust manifolds/catalysts/front tubes for stripped exhaust sensor threads may not be considered a warrantable expense.
This procedure can be performed by two methods:
Method #1 - If the Sensor Can Be Easily Accessed
^ The procedure can be performed on the vehicle.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 388
^ The exhaust manifold/catalyst/front tube will not have to be removed.
Method #2 - If the Sensor Cannot Be Easily Accessed
^ The exhaust manifold/catalyst/front tube must be removed from the vehicle.
^ The procedure will be performed with the part clamped in a vice.
Method #2 is described in this bulletin. Method #1 is the same as Method #2 except that it is performed on the vehicle.
Service Procedure
Rust Penetrant
Recommended rust penetrants to be used in this procedure:
NOTES:
^ Rust penetrant is considered a shop supply.
^ Nissan Rust Penetrant can be ordered through the Nissan Direct Ship Chemical Care Product Program, Website order via link on dealer portal.
^ WD-40 is available from various local sources.
Removal Tool
^ When removing a seized exhaust sensor with a specialty socket (which contains a slit to accommodate the wiring harness), it may spread open and
strip the sensor.
^ Before this occurs, it is recommended to cut the wiring harness from the sensor and use a box end wrench or 6-point deep well socket.
1. Clamp the exhaust manifold/catalyst/front tube in a vice.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 389
2. Spray the sensor with the rust penetrant for 2 to 3 seconds.
^ It is important that the spray is directed at the base of the sensor to ensure it penetrates into the threads.
3. Loosen the sensor approximately 10 degrees.
4. Spray with rust penetrant again for 2 to 3 seconds.
5. Tighten the sensor 10 degrees, then loosen the sensor 10 degrees.
^ Repeat this motion several times until the sensor begins to turn more easily.
6. Continue the tightening/loosening motion while gradually unscrewing the sensor. Stop when the sensor will not unscrew any further.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 390
7. Spray with rust penetrant again for 2 to 3 seconds.
8. Repeat steps 6 and 7 until the sensor is removed.
9. Use compressed air to remove any metal debris from inside the boss threads.
CAUTION:
DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.
10. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.
11. Spray the boss threads with rust penetrant for 2 to 3 seconds.
12. Run a thread chaser through the boss to clean the threads.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 391
^ Use Kent Moore part number J-43897-18 or J43897-12.
13. Use compressed air to remove any remaining debris.
CAUTION:
DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.
14. If metal debris remains trapped in the boss threads, use a spiral nylon brush to remove it.
15. Tilt the manifold/catalyst/front tube so that the metal debris falls out of the part.
16. Apply compressed air through the boss to blow out any remaining debris.
CAUTION:
DO NOT perform this step if the procedure is being done on the vehicle (Method #1). Doing so may cause metal debris to enter the engine cylinders.
17. Install the new sensor as described in the applicable Electronic Service Manual (ESM).
Friday, May 31, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221
2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221
Lighting - Exterior Lamp Fogging
Classification: EL03-030F
Reference: NTB03-074F
Date: February 21, 2012
EXTERIOR LAMP FOGGING
This bulletin has been amended. The Applied Vehicles section and the first paragraph of the Service Information section have been revised. Please
discard all previous versions.
APPLIED VEHICLES: 2001-2012 Nissan, All Models
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 158
SERVICE INFORMATION
Occasionally customers may notice water vapor or fog in the exterior lamps. This is generally NOT due to a defect.
The following information, illustrations, and flow chart are provided to help you in determining if an incident for water/condensation in the lamps is
normal or not.
All current exterior lamp assemblies are vented to the atmosphere (not sealed).
^ This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the lamp.
^ Moisture in the air sometimes "travels" into and out of the lamp assembly through these vents.
^ Certain environmental conditions may cause moisture to condense.
^ The fogging/cloudiness should disappear over time when the lamp is in a dry environment.
Fog may temporarily form inside the lens of the exterior lamp assemblies based on environmental conditions or sudden temperature changes (such as
in a car wash, or parked on a cold, sunny day). This is normal. See Figure 1.
NOTE:
This condensation can appear anywhere on the outer lens, typically at its coldest location.
If the moisture trickles, drips, or pools, it may not be considered normal and the lamp assembly may have a water leak path. See Figure 2 for an
example.
If large drops of water collect inside the lens, refer to the flow chart below to find the next step.
SERVICE PROCEDURE
Should a customer note water in a lamp assembly, please use the following flow chart to determine if the condition is normal or requires lamp
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 159
Thursday, May 30, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 10-038 Date: 100311
2014 Nissan-Datsun Altima Diagrams. DTC # 10-038 Date: 100311
Electrical - JIS & CCA Battery Testing Information
Classification: EL10-010
Reference: NTB10-038
Date: March 11, 2010
NISSAN; TESTING JIS-TYPE & CCA-TYPE BATTERIES
APPLIED VEHICLES: All Nissan vehicles
SERVICE INFORMATION
Nissan vehicles equipped with standard lead/acid batteries use one of two different types with unique battery rating specifications: JIS & CCA.
JIS = Japan Industrial Standard, used for Japan produced batteries
CCA = Cold Cranking Amps, standard for North American produced batteries
IMPORTANT:
^ JIS batteries have different testing specifications than CCA batteries.
^ If you must use the GR8 Battery Tester in a mode other than MODEL mode, JIS Mode MUST ALWAYS BE USED for JIS batteries otherwise an
incorrect result will occur. NEVER test a JIS battery using the CCA test in the GR8; the test software in the GR8 is different for JIS and CCA
modes. ANY CCA value you may have for a JIS-type battery is inaccurate for testing purposes.
ALWAYS test with the GR8 using the MODEL mode (if available).
^ Selecting MODEL and vehicle type will automatically select the proper JIS or CCA value for the Original Equipment battery.
^ If the applicable vehicle is not listed update the GR8 to make sure it has the most recent data package.
^ If the applicable vehicle still is not listed:
1) Determine which type of battery (CCA or JIS) is installed in the vehicle. See below for descriptions of each battery.
2) Select CCA or JIS in the GR8 based on the type of battery installed. See below for more information.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 224
Determine the Battery Type
Batteries with JIS (Japanese Industrial Standard) Number
^ Batteries installed in vehicles produced in Japan have a JIS number embossed in the plastic on top of the battery.
^ These vehicles have a VIN that begins with the letter "J".
Batteries with CCA (Cold Cranking Amps) Number
^ Batteries installed in vehicles produced in North America have a CCA number displayed on the label attached to the top of the battery.
^ These vehicles have a VIN that begins with a number: 1, 3, or 5.
Selecting CCA or JIS in the GR8 Battery Tester
Vehicles with JIS Battery
^ Select JIS, then choose the option that matches the first five (5) characters of the JIS number on the battery.
NOTE:
DO NOT select CCA when testing a JIS battery.
Vehicles with CCA Battery
^ Select CCA, then choose the option that matches the number following "Cold Cranking Amps" on the battery.
Reference Material
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 225
The information shown above can be printed and attached to the GR8, if needed.
Wednesday, May 29, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 10-075 Date: 100608
2014 Nissan-Datsun Altima Diagrams. DTC # 10-075 Date: 100608
Body - Front/Rear Door Weatherstrip Loose/Pulled Out
Classification: BT10-012
Reference: NTB10-075
Date: June 8, 2010
2007-2010 ALTIMA; DOOR WEATHERSTRIP LOOSE
APPLIED VEHICLES:
2007 - 2010 Altima Sedan (L32)
2008 - 2010 Altima Coupe (CL32)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 425
2007 - 2010 Altima Hybrid (L32HV)
IF YOU CONFIRM:
The front or rear door weatherstrip has pulled out, or is loose (see Figure 1).
ACTION:
Re-install the weatherstrip using the SERVICE PROCEDURE of this bulletin.
^ Apply this repair to the incident door weatherstrip only.
NOTE:
Do NOT replace any door weatherstrip for this incident, if it should occur.
IMPORTANT:
The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 426
1. Remove the door weatherstrip from the sash channel area of the upper door frame. Figure 3 shows a cutaway of the weatherstrip.
a. Carefully peel up the weatherstrip's "lower" ridge from its channel (see Figure 3).
b. Complete upper weatherstrip removal by pulling its "upper" ridge from its channel (see Figure 3).
2. Clean out the sash channel and the bottom of the weatherstrip.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 427
^ Use a clean shop towel and isopropyl alcohol or equivalent cleaner (see Figure 4 and 5).
3. Apply two (2) beads of Nissan Weatherstrip Cement (cement) along the whole upper channel as shown in Figure 6.
NOTE:
Use Nissan Weatherstrip Cement only. See (PARTS INFORMATION).
^ Bead width: approximately 3/32 inch (2.5 mm).
^ Apply the beads the length of the channel, and 1/2 inch (13 mm) from each end.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 428
4. Re-install the weatherstrip immediately after cement application as follows:
a. Press in the weatherstrip upper ridge into the upper channel.
b. While maintaining upward tension to keep it in the upper channel, press the weatherstrip's lower ridge into its channel.
^ If necessary, use a plastic "finesse stick" or similar trim tool to push the lower ridge over and into its channel (see Figure 7).
c. Using the plastic "finesse stick" or similar trim tool, push on the mid-section area to fully seat the weatherstrip (see Figure 8).
^ Run your finger down this area to feel for any high spots. High spots will indicate where the weatherstrip ridge is not fully seated.
^ Re-seat as needed.
5. Inspect proper weatherstrip installation by carefully lifting up on the weatherstrip slightly.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 429
^ Figure 9 shows an OK condition.
^ Figure 10 shows a No Good condition.
> To correct this condition, refer back and perform Step 4b and 4c as needed.
6. Clean off any excess cement with a suitable cleaner.
7. Let the cement dry for at least 15 minutes, and then re-check for proper adhesion.
Tuesday, May 28, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 10-068E Date: 130128
2014 Nissan-Datsun Altima Diagrams. DTC # 10-068E Date: 130128
Campaign P0337 - Navigation Software Update For Various Issues
Reference:
NTB10-068e
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN
NISSAN NAVIGATION SOFTWARE UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 506
CAMPAIGN ID #: P0337
APPLIED VEHICLES:
2010 Altima Sedan, Coupe, and Hybrid (L32, CL32, and L32HV)
2010 Maxima (A35)
2010 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, and iPod(R) functions may not be working as intended. To remedy this
potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P0337 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for all applied models in this campaign except GT-R.
^ Do not use disc 3/3.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 507
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
^ This disc also replaces disc NTB10-125b/NTB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-(800) 347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
This SERVICE PROCEDURE contains three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program - all except GT-R
Loading the Program for GT-R
C. Check Bluetooth(R) Setting - all except GT-R
Check Bluetooth(R) Setting for GT-R
A: Disable Bluetooth(R) Function
1. Set the parking brake.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 508
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING button on the switch panel.
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program - all except GT-R For GT-R.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 509
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No. 1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD/DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB1-0068 (Disc 1/3) into the in-dash CD/DVD player.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 510
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 511
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 512
^ If "Now preparing loading" shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 513
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the program has finished loading:
^ "Program loading is completed" will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update (step 22).
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25 on the next page.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 514
23. "Rewriting boot data (Figure 20) and "Rewriting program data (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 515
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting (all except GT-R)
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 516
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
B: Loading the Program for GT-R
1. Turn the ignition ON.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
5. Load the new disc "NTB12-070/ITB12-054 Re-programming Software DVD into CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to Check Bluetooth(R) Setting for GT-R.
^ If "Now preparing loading" shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 517
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the reprogram has finished loading:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 518
^ "Program loading" is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update (step 9).
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 519
10. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed" will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure A11 is displayed it, indicates that the reprogram has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 520
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 6 through 12 again.
13. Eject the DVD.
14. Go to C: Check Bluetooth(R) Setting for GT-R.
C: Check Bluetooth(R) Setting for GT-R
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 521
^ Bluetooth is OFF when the ON indicator is "grayed out".
4. Turn the ignition OFF. The process is complete.
Sunday, May 26, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 09-140 Date: 091208
2014 Nissan-Datsun Altima Diagrams. DTC # 09-140 Date: 091208
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 392
A/T - CVT Oil Leak Diagnosis Information
Classification: AT09-012
Reference: NTB09-140
Date: December 8, 2009
CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE
APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)
SERVICE INFORMATION
If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.
1. Thoroughly clean off the area of the suspected leak.
2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.
3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).
4. Inspect with lamp from J-43926 A/C Dye Kit*
If no fluorescent oil trace/leak is found, the stain is probably:
^ corrosion protection chemicals sprayed on the transmission
and/or
^ lubricants which are sometimes used to ease the assembly process.
NOTE:
These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.
If a fluorescent oil trace/leak is found:
^ Repair using standard warranty procedures.
*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.
NOTE:
The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.
Saturday, May 25, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 09-111B Date: 100901
2014 Nissan-Datsun Altima Diagrams. DTC # 09-111B Date: 100901
Interior - Driver's Seat Bottom Shifts/Rocks Slightly
Classification: BT09-057B
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 455
Reference: NTB09-111B
Date: September 1, 2010
2008-2010 ALTIMA COUPE; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
This bulletin has been amended. Replacement of the seat side finisher has been added to the service procedure and the Parts Information has been
updated. Please discard previous versions.
APPLIED VEHICLES: 2008-2010 Altima Coupe (CL32) -equipped with power seat
APPLIED VIN:
2008-2009 vehicles - All
2010 vehicles built before 1N4(*)L2E(**)A(*) 117207
APPLIED DATE: Vehicles built on or before November 18, 2009
IF YOU CONFIRM:
The driver seat bottom (power seat only) very slightly "rocks" and/or "shifts" back and forth when accelerating, braking, or when making a turn.
ACTION:
Replace the driver seat cushion frame assembly (adjuster assembly) with a new one.
^ During reassembly use a new side seat finisher.
IMPORTANT:
The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service
Procedure as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 456
CLAIMS INFORMATION
SERVICE PROCEDURE
IMPORTANT:
Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),
such as an air bag.
1. Write down all radio station pre-sets.
2. If equipped - write down / record the following customer settings for the ATC (Automatic Temperature Control) system. (Refer to the Service
Manual as needed):
^ Temperature Setting Trimmer
^ Foot Position Setting Trimmer
^ Inlet Port Memory Function
3. Turn the ignition switch OFF.
4. Disconnect both battery cables - negative cable first.
5. WARNING: Wait for at least 3 minutes before removing the driver seat.
6. Carefully remove the driver seat from the vehicle.
^ Refer to the Service Manual section SE for seat removal procedure.
CAUTION:
Use covers as needed to protect interior surfaces from being scratched or damaged.
7. Replace the cushion frame assembly (adjuster assembly).
^ Refer to the 2010 Altima Coupe Service Manual - SE Section, Front Seat Driver Side: Disassembly and Assembly.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 457
^ During reassembly use a new side finisher listed in the Parts Information.
NOTE:
This bulletin contains additional helpful information for Seatback Finisher Removal (See below).
8. Connect the battery cables - positive cable first.
9. Reset the clock and the radio station presets.
10. Refer to the Service Manual for the following "reset / relearn procedures:
^ Power Window Initialization
^ Sunroof Memory Reset/Initialization
^ ATC Temperature Setting Trimmer (A/C system)
^ ATC Foot Position Setting Trimmer (A/C system)
^ ATC Inlet Port Memory Function - FRE and REC (A/C system)
^ Rear View Monitor Possible Route Line Center Position Adjustment (if equipped)
^ Steering Angle Sensor Neutral Position
11. Inform the customer they will need to "reset" their Automatic Drive Positioner.
Seatback Finisher Removal
1. Move / adjust the seat bottom and seat back to the full forward positions.
NOTE:
The seat back finisher is held on with:
^ 2 top hooks
^ 2 side clips
^ 2 bottom clips
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 458
2. Reach under the seat and disconnect the 2 elastic straps for the toe flap.
3. Insert your fingers behind the bottom corner of the finisher.
4. Locate the bottom clip with your fingers.
5. Pull the finisher next to the clip to unsnap the clip.
6. Repeat 3, 4 and 5 for the other bottom clip.
7. Insert your fingers into the side of the finisher.
8. Locate the "side" clip.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 459
9. Support the finisher with the palm of your hand.
10. Pull the finisher next to the clip to unsnap the clip.
11. Repeat 7 to 10 for the other "side" clip.
12. Pull down on the finisher to remove it.