Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221

2014 Nissan-Datsun Altima Diagrams. DTC # 03-074F Date: 120221



Lighting - Exterior Lamp Fogging



Classification: EL03-030F



Reference: NTB03-074F



Date: February 21, 2012



EXTERIOR LAMP FOGGING



This bulletin has been amended. The Applied Vehicles section and the first paragraph of the Service Information section have been revised. Please



discard all previous versions.



APPLIED VEHICLES: 2001-2012 Nissan, All Models



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 158



SERVICE INFORMATION



Occasionally customers may notice water vapor or fog in the exterior lamps. This is generally NOT due to a defect.



The following information, illustrations, and flow chart are provided to help you in determining if an incident for water/condensation in the lamps is



normal or not.



All current exterior lamp assemblies are vented to the atmosphere (not sealed).



^ This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the lamp.



^ Moisture in the air sometimes "travels" into and out of the lamp assembly through these vents.



^ Certain environmental conditions may cause moisture to condense.



^ The fogging/cloudiness should disappear over time when the lamp is in a dry environment.



Fog may temporarily form inside the lens of the exterior lamp assemblies based on environmental conditions or sudden temperature changes (such as



in a car wash, or parked on a cold, sunny day). This is normal. See Figure 1.



NOTE:



This condensation can appear anywhere on the outer lens, typically at its coldest location.



If the moisture trickles, drips, or pools, it may not be considered normal and the lamp assembly may have a water leak path. See Figure 2 for an



example.



If large drops of water collect inside the lens, refer to the flow chart below to find the next step.



SERVICE PROCEDURE



Should a customer note water in a lamp assembly, please use the following flow chart to determine if the condition is normal or requires lamp



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 159

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more