2014 Nissan-Datsun Altima Diagrams. DTC # 11-013 Date: 110215

2014 Nissan-Datsun Altima Diagrams. DTC # 11-013 Date: 110215

Interior - A-Pillar Trim Removal/Installation Procedure

Classification: BT11-003

Reference: NTB11-013

Date: February 15, 2011

2010 - 2011 ALTIMA; FRONT PILLAR FINISHER REMOVAL

APPLIED VEHICLE: 2010-2011 Altima Sedan (L32)

2010-2011 Altima Hybrid (L32HV)

NOTE:

Does not apply to Altima Coupe

SERVICE INFORMATION

If either one or both front pillar finishers has to be removed for any reason, refer to REPAIR PROCEDURE.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 232

SERVICE PROCEDURE

Remove Front Pillar Finisher

IMPORTANT

1. Remove the front body side welt (see Figure 1).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 233

2. Snap loose both clips by carefully prying with a suitable tool where shown in Figure 2.

CAUTION:

The lower clip will not completely snap loose. Attempting to completely snap loose by force may damage the finisher. Continue to Step 3 for proper

removal.

3. Unfasten the lower clip from the front pillar finisher (finisher) with a suitable tool. See Figure 3 and 4.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 234

4. Tip the top of the finisher inward, and then pull out (see Figure 5).

5. Remove the lower clip from the "A" pillar by pinching and then flipping upward (see Figure 6).

Re-install Front Pillar Finisher

1. Insert the lower clip on the finisher (see Figure 7).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 235

2. Re-install the finisher by inserting its locator tabs into their slots (see Figure 8 and 9).

3. Align the lower and upper clips into their slots, and then press both into place (see Figure 10).

4. Re-install the front body side welt.

2014 Nissan-Datsun Altima Diagrams. DTC # 00-042B Date: 110215

2014 Nissan-Datsun Altima Diagrams. DTC # 00-042B Date: 110215

Interior/Restraints - Seat Trim Material Information

Classification: RS00-003B

Reference: NTB00-042B

Date: February 15, 2011

RECOMMENDATION AGAINST MAKING CHANGES TO FRONT SEAT ASSEMBLY TRIM MATERIALS

This bulletin has been amended. The Applied Vehicles and Service Information have been updated. Discard all previous copies.

APPLIED VEHICLES: ALL NISSAN VEHICLES

SERVICE INFORMATION

Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death.

Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically

applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers seat pads or seat storage pouches etc. around or over

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 231

the seat back and the passenger seat cushion.

^ Damage or failure due to changes or modifications to the front seat assembly are not covered under the warranty.

^ Damage or failure due to changes or modifications to the front seat assembly are not subject to indemnification under the Nissan Dealer Sales and

Service Agreement.

^ Dealers may be obligated under their Nissan Dealer Sales and Service Agreement to indemnify Nissan for any damages, injuries, or deaths caused

by modification of the front seat assemblies.

^ NMAC will not provide retail advance for any changes to the front seat trim materials from factory equipped condition.

^ Vehicles with any changes to the front seat trim materials from factory equipped condition may not be eligible for the Signature PURCHASE

Plan.

SEE Section 1 of the applicable Owner's Manual for important Warnings and other information about Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor.

2017 Nissan-Datsun Altima Technical Service Bulletin # 00-042B Date: 110215

2017 Nissan-Datsun Altima Technical Service Bulletin # 00-042B Date: 110215

Interior/Restraints - Seat Trim Material Information

Classification: RS00-003B

Reference: NTB00-042B

Date: February 15, 2011

RECOMMENDATION AGAINST MAKING CHANGES TO FRONT SEAT ASSEMBLY TRIM MATERIALS

This bulletin has been amended. The Applied Vehicles and Service Information have been updated. Discard all previous copies.

APPLIED VEHICLES: ALL NISSAN VEHICLES

SERVICE INFORMATION

Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death.

Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically

applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers seat pads or seat storage pouches etc. around or over

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 231

the seat back and the passenger seat cushion.

^ Damage or failure due to changes or modifications to the front seat assembly are not covered under the warranty.

^ Damage or failure due to changes or modifications to the front seat assembly are not subject to indemnification under the Nissan Dealer Sales and

Service Agreement.

^ Dealers may be obligated under their Nissan Dealer Sales and Service Agreement to indemnify Nissan for any damages, injuries, or deaths caused

by modification of the front seat assemblies.

^ NMAC will not provide retail advance for any changes to the front seat trim materials from factory equipped condition.

^ Vehicles with any changes to the front seat trim materials from factory equipped condition may not be eligible for the Signature PURCHASE

Plan.

SEE Section 1 of the applicable Owner's Manual for important Warnings and other information about Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 00-042B Date: 110215

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 00-042B Date: 110215

Interior/Restraints - Seat Trim Material Information

Classification: RS00-003B

Reference: NTB00-042B

Date: February 15, 2011

RECOMMENDATION AGAINST MAKING CHANGES TO FRONT SEAT ASSEMBLY TRIM MATERIALS

This bulletin has been amended. The Applied Vehicles and Service Information have been updated. Discard all previous copies.

APPLIED VEHICLES: ALL NISSAN VEHICLES

SERVICE INFORMATION

Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death.

Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically

applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers seat pads or seat storage pouches etc. around or over

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 231

the seat back and the passenger seat cushion.

^ Damage or failure due to changes or modifications to the front seat assembly are not covered under the warranty.

^ Damage or failure due to changes or modifications to the front seat assembly are not subject to indemnification under the Nissan Dealer Sales and

Service Agreement.

^ Dealers may be obligated under their Nissan Dealer Sales and Service Agreement to indemnify Nissan for any damages, injuries, or deaths caused

by modification of the front seat assemblies.

^ NMAC will not provide retail advance for any changes to the front seat trim materials from factory equipped condition.

^ Vehicles with any changes to the front seat trim materials from factory equipped condition may not be eligible for the Signature PURCHASE

Plan.

SEE Section 1 of the applicable Owner's Manual for important Warnings and other information about Front Seat-Mounted Side-Impact

Supplemental Air Bags and Passenger Occupant Classification Sensor.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-013 Date: 110215

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-013 Date: 110215

Interior - A-Pillar Trim Removal/Installation Procedure

Classification: BT11-003

Reference: NTB11-013

Date: February 15, 2011

2010 - 2011 ALTIMA; FRONT PILLAR FINISHER REMOVAL

APPLIED VEHICLE: 2010-2011 Altima Sedan (L32)

2010-2011 Altima Hybrid (L32HV)

NOTE:

Does not apply to Altima Coupe

SERVICE INFORMATION

If either one or both front pillar finishers has to be removed for any reason, refer to REPAIR PROCEDURE.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 232

SERVICE PROCEDURE

Remove Front Pillar Finisher

IMPORTANT

1. Remove the front body side welt (see Figure 1).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 233

2. Snap loose both clips by carefully prying with a suitable tool where shown in Figure 2.

CAUTION:

The lower clip will not completely snap loose. Attempting to completely snap loose by force may damage the finisher. Continue to Step 3 for proper

removal.

3. Unfasten the lower clip from the front pillar finisher (finisher) with a suitable tool. See Figure 3 and 4.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 234

4. Tip the top of the finisher inward, and then pull out (see Figure 5).

5. Remove the lower clip from the "A" pillar by pinching and then flipping upward (see Figure 6).

Re-install Front Pillar Finisher

1. Insert the lower clip on the finisher (see Figure 7).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 235

2. Re-install the finisher by inserting its locator tabs into their slots (see Figure 8 and 9).

3. Align the lower and upper clips into their slots, and then press both into place (see Figure 10).

4. Re-install the front body side welt.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-013 Date: 110215

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-013 Date: 110215

Interior - A-Pillar Trim Removal/Installation Procedure

Classification: BT11-003

Reference: NTB11-013

Date: February 15, 2011

2010 - 2011 ALTIMA; FRONT PILLAR FINISHER REMOVAL

APPLIED VEHICLE: 2010-2011 Altima Sedan (L32)

2010-2011 Altima Hybrid (L32HV)

NOTE:

Does not apply to Altima Coupe

SERVICE INFORMATION

If either one or both front pillar finishers has to be removed for any reason, refer to REPAIR PROCEDURE.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 232

SERVICE PROCEDURE

Remove Front Pillar Finisher

IMPORTANT

1. Remove the front body side welt (see Figure 1).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 233

2. Snap loose both clips by carefully prying with a suitable tool where shown in Figure 2.

CAUTION:

The lower clip will not completely snap loose. Attempting to completely snap loose by force may damage the finisher. Continue to Step 3 for proper

removal.

3. Unfasten the lower clip from the front pillar finisher (finisher) with a suitable tool. See Figure 3 and 4.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 234

4. Tip the top of the finisher inward, and then pull out (see Figure 5).

5. Remove the lower clip from the "A" pillar by pinching and then flipping upward (see Figure 6).

Re-install Front Pillar Finisher

1. Insert the lower clip on the finisher (see Figure 7).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 235

2. Re-install the finisher by inserting its locator tabs into their slots (see Figure 8 and 9).

3. Align the lower and upper clips into their slots, and then press both into place (see Figure 10).

4. Re-install the front body side welt.