Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-096 Date: 111019

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-096 Date: 111019



Audio/Cell Phone - IPod(R)/iPhone(R) USB Interface Issue



Classification: EL11-038



Reference: NTB11-096



Date: October 19, 2011



iPOD(R) / iPHONE(R) ISSUES USING VEHICLE USB INTERFACE



APPLIED VEHICLES: All Nissan vehicles equipped with a USB Interface



SERVICE INFORMATION



If an IPod(R)/ iPhone(R) related concern is verified on a vehicle while using the USB interface, perform the steps in this bulletin for initial



diagnosis.



NOTE:



For vehicles equipped with a Navigation system, make sure to confirm whether the customer is experiencing the issue while using the USB interface



or the Bluetooth(R) Audio Streaming feature. This bulletin applies only if the issue occurs while using the USB interface.



1. Power OFF/ON (restart/reset) the iPod(R)/ iPhone(R)



^ The restart/reset procedure is not the same for every iPod(R)/ iPhone(R). The restart/reset procedures can be found at www.apple.com/support.



2. Check the USB cable.



^ Some aftermarket cables can cause issues with USB connectivity. If the customer is using an iPod(R)/ iPhone(R), the best cable to use is the



Apple Inc. branded USB cable.



^ Make sure the cable does not have a short circuit or other concern.



3. Confirm the latest software is installed on the iPod(R)/ iPhone(R)



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 188



^ Many concerns are addressed by installing the latest iPod(R)/ iPhone(R) software update from Apple Inc.



^ View the software version of the iPod(R)/iPhonee(R) by navigating to the Settings area of the device, then selecting General > About or Settings.



^ Visit http://support.apple.com/downloads and select the applicable device to view the latest software update offered by Apple Inc.



4. If steps 1-3 have not resolved the concern:



a. Disconnect the cable from the USB interface.



b. Turn OFF the vehicle, wait one (1) minute, then turn the vehicle back to ACC or ON.



c. Connect a different USB device to the USB interface in the customer's vehicle, then try to duplicate the concern.



NOTE:



Other USB devices include a USB thumb drive formatted at either Fat16 or Fat32 with .mp3 or .wma files, or another type of iPod(R) (iTouch(R),



Classic(R), Nano(R), etc.).



d. If the concern still exists with a known good USB device, refer to the applicable Electronic Service Manual (ESM) for diagnosis on the USB



interface and/or AV Control Unit connectors.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more