2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621

Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.

Classification: EC10-017

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252

Reference: NTB10-079

Date: June 21, 2010

MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED

APPLIED VEHICLES: 2002 and later Nissan vehicles

IF YOU CONFIRM

The MIL is "ON" with P0128 (Thermostat Function) stored.

ACTIONS

1. Check to see if an aftermarket remote starter system is installed.

^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.

2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.

3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-078 Date: 100621

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-078 Date: 100621

Engine Controls - ECM Programming Interruption Recovery

Classification: EC10-015

Reference: NTB10-078

Date: June 21, 2010

REPROGRAM INTERRUPTION RECOVERY PROCEDURE

SERVICE INFORMATION

A complete step-by-step General Procedure for CONSULT-III (C-III) ECM Reprogram Interruption Recovery is now available by attachment in this

bulletin.

While performing ECM (Engine Control Module) reprogramming, the reprogramming may stop (become interrupted) before it is 100% complete.

One of two messages may appear:

^ The VI probe is disconnected on USB, please check the connection of the probe.

^ Reprogramming fail, "Error code 0".

In many cases, reprogramming recovery is possible and the ECM may not need to be replaced if the complete ECM part number has been registered

into the ECM before reprogramming stopped.

NOTE:

ECM is referred to as ECU in C-III.

The ECM Reprogram Interruption Recovery General Procedure applies to Technical Service Bulletins that include ECM reprogramming published

in April 2010 and later.

IMPORTANT: BEFORE STARTING REPROGRAMMING

^ Connect a battery charger to the vehicle battery.

^ Be sure to turn OFF all vehicle electrical loads.

^ For ECM reprogramming, the C-III MUST be connected to the VI using the USB cable.

^ Be sure to connect the AC Adapter.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 253

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 254

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 255

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 256

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 257

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 258

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 259

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 260

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 261

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 262

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 263

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 264

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 265

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 266

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-078 Date: 100621

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-078 Date: 100621

Engine Controls - ECM Programming Interruption Recovery

Classification: EC10-015

Reference: NTB10-078

Date: June 21, 2010

REPROGRAM INTERRUPTION RECOVERY PROCEDURE

SERVICE INFORMATION

A complete step-by-step General Procedure for CONSULT-III (C-III) ECM Reprogram Interruption Recovery is now available by attachment in this

bulletin.

While performing ECM (Engine Control Module) reprogramming, the reprogramming may stop (become interrupted) before it is 100% complete.

One of two messages may appear:

^ The VI probe is disconnected on USB, please check the connection of the probe.

^ Reprogramming fail, "Error code 0".

In many cases, reprogramming recovery is possible and the ECM may not need to be replaced if the complete ECM part number has been registered

into the ECM before reprogramming stopped.

NOTE:

ECM is referred to as ECU in C-III.

The ECM Reprogram Interruption Recovery General Procedure applies to Technical Service Bulletins that include ECM reprogramming published

in April 2010 and later.

IMPORTANT: BEFORE STARTING REPROGRAMMING

^ Connect a battery charger to the vehicle battery.

^ Be sure to turn OFF all vehicle electrical loads.

^ For ECM reprogramming, the C-III MUST be connected to the VI using the USB cable.

^ Be sure to connect the AC Adapter.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 253

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 254

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 255

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 256

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 257

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 258

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 259

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 260

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 261

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 262

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 263

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 264

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 265

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 266

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-079 Date: 100621

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-079 Date: 100621

Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.

Classification: EC10-017

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252

Reference: NTB10-079

Date: June 21, 2010

MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED

APPLIED VEHICLES: 2002 and later Nissan vehicles

IF YOU CONFIRM

The MIL is "ON" with P0128 (Thermostat Function) stored.

ACTIONS

1. Check to see if an aftermarket remote starter system is installed.

^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.

2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.

3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.

2014 Nissan-Datsun Altima Diagrams. DTC # 10-078 Date: 100621

2014 Nissan-Datsun Altima Diagrams. DTC # 10-078 Date: 100621

Engine Controls - ECM Programming Interruption Recovery

Classification: EC10-015

Reference: NTB10-078

Date: June 21, 2010

REPROGRAM INTERRUPTION RECOVERY PROCEDURE

SERVICE INFORMATION

A complete step-by-step General Procedure for CONSULT-III (C-III) ECM Reprogram Interruption Recovery is now available by attachment in this

bulletin.

While performing ECM (Engine Control Module) reprogramming, the reprogramming may stop (become interrupted) before it is 100% complete.

One of two messages may appear:

^ The VI probe is disconnected on USB, please check the connection of the probe.

^ Reprogramming fail, "Error code 0".

In many cases, reprogramming recovery is possible and the ECM may not need to be replaced if the complete ECM part number has been registered

into the ECM before reprogramming stopped.

NOTE:

ECM is referred to as ECU in C-III.

The ECM Reprogram Interruption Recovery General Procedure applies to Technical Service Bulletins that include ECM reprogramming published

in April 2010 and later.

IMPORTANT: BEFORE STARTING REPROGRAMMING

^ Connect a battery charger to the vehicle battery.

^ Be sure to turn OFF all vehicle electrical loads.

^ For ECM reprogramming, the C-III MUST be connected to the VI using the USB cable.

^ Be sure to connect the AC Adapter.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 253

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 254

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 255

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 256

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 257

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 258

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 259

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 260

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 261

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 262

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 263

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 264

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 265

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 266

2014 Nissan-Datsun Altima Diagrams. DTC # 10-079 Date: 100621

2014 Nissan-Datsun Altima Diagrams. DTC # 10-079 Date: 100621

Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.

Classification: EC10-017

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252

Reference: NTB10-079

Date: June 21, 2010

MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED

APPLIED VEHICLES: 2002 and later Nissan vehicles

IF YOU CONFIRM

The MIL is "ON" with P0128 (Thermostat Function) stored.

ACTIONS

1. Check to see if an aftermarket remote starter system is installed.

^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.

2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.

3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.