NISSAN: February 2019

Thursday, February 28, 2019

2014 Nissan-Datsun Altima Diagrams. DTC # 12-030 Date: 120322

Steering - Power Steering Hose Service Part Change

Classification: ST11-008

Reference: NTB12-030

Date: March 22, 2012

ALTIMA, MAXIMA;

POWER STEERING HOSE SERVICE PART CHANGE

APPLIED VEHICLES:2007-2011 Altima (C/L32)

2009-2011 Maxima (A35)

SERVICE INFORMATION

If the high pressure hose on an Applied Vehicle needs to be replaced for any reason:

^ The hose now comes without the pressure sensor (refer to Figure 1).

^ When replacing this hose, reuse the existing pressure sensor. Replace the pressure sensor ONLY IF there is a pressure sensor related issue.

^ Do not replace other related hoses unless necessary (i.e., do not replace as a set).

^ Do not damage the pressure sensor during removal or installation.

^ Always use a new 0-ring when installing a new or existing pressure sensor (refer to Figure 1).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 129

^ Pressure sensor mounting torque: 19.6 Nm (2.0 kg-m, 14.5 ft lb)

^ If only the pressure sensor needs replacement, do not replace any hoses.

^ Always replace both copper washers (mounted at the power steering pump).

CAUTIONS:

> Do not allow dirt or contamination to enter the hydraulic system.

> Always secure the pressure sensor mounting block in a soft jaw vise when removing and installing the pressure sensor. Do not clamp onto

the "banjo" end of the hose.

^ Refer to the appropriate Electronic Service Manual (ESM) for power steering hose removal, installation, and torque specifications.

2014 Nissan-Datsun Altima Diagrams. DTC # 08-033C Date: 111003

Tire Monitor System - Tire Pressure Info.

Classification: WT08-003C

Reference: NTB08-033C

Date: October 3, 2011

TIRE PRESSURE INFORMATION FOR VEHICLES WITH TPMS

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 209

The publication date on this bulletin has been amended to include the newest models.

APPLIED VEHICLES: All Nissan vehicles with Tire Pressure Monitor System (TPMS)

SERVICE INFORMATION

The Low Tire Pressure Warning Lamp will illuminate continuously (not flashing) if the tire pressure is low in any of the four road tires.

^ This is not an indication of a malfunction. Rather, it is a signal to the driver that the tire pressure in the vehicle must be adjusted.

Tire pressure must be adjusted/corrected at or above the pressure shown on the TIRE AND LOADING INFORMATION label before the Low Tire

Pressure Warning Light will go OFF.

^ Regular tire pressure maintenance such as described in this bulletin is not covered under the warranty.

The air pressure inside a tire can change due to several factors, such as:

^ Seasonal temperature change

^ Tire temperature change due to driving

^ Natural pressure loss over time

Compensate for the above temperature factors when adjusting and setting tire pressure.

Each vehicle is equipped from the factory with a TIRE AND LOADING INFORMATION label.

This label lists the COLD tire pressure setting for the original tires on the specific vehicle.

NOTE:

Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile at moderate speeds.

When setting / adjusting tire pressure, make sure to use an accurate tire pressure gauge.

Use the following information for reference:

Temperature:

^ Tire pressure changes approximately 0.8 psi for every 10锟斤拷F of temperature change. As temperature decreases, pressure decreases.

^ Tire pressure may change 3 - 5 psi between a Cold reading and a reading taken just after the vehicle has been driven for several miles.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 210

^ Seasonal temperature change can result in tire pressure that is low enough to turn on the Low Tire Pressure Warning Light.

Example 1 - Seasonal Temperature Change:

^ The temperature of the vehicle is 70锟斤拷F after sitting in the shop.

^ Ambient temperature outside the shop is 30锟斤拷F or will soon fall to 30锟斤拷F due to seasonal change.

^ Recommended pressure on the TIRE AND LOADING INFORMATION label is 35 psi.

^ The tire pressure should be compensated an additional +3 psi and adjusted to 38 psi to avoid dropping below the label value when the vehicle

experiences cooler ambient air temperature.

^ Compensation should also be used in the PDI process as needed.

Example 2 - WARM Tires:

^ A vehicle arrives to the dealer after being driven across town.

^ The WARM tire pressure reading is 32 psi.

^ Recommended COLD tire pressure on the TIRE AND LOADING INFORMATION label is 35 psi.

^ The tire pressure should be compensated an additional +3 psi and adjusted to 38 psi to avoid dropping below the label value when the tires cool.

Natural tire pressure loss over time:

^ Vehicle tire pressure can naturally decrease by approximately 1.0 - 1.5 psi per month. This will vary due to seasonal temperature change.

^ After 6 to 8 months tire pressure may be low enough to turn ON the Low Tire Pressure Warning Light.

High Altitude

^ At high altitude locations, a standard tire pressure gauge may show the tire pressure higher than the TPMS system. If the gauge reading is not

accounted for, this could result in turning ON the Low Tire Pressure Warning Light.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 211

^ Standard tire pressure gauge readings increase about 1.0 psi for every 2,200 ft of altitude increase above sea level (up to 10,000 ft). See graph 3

above.

^ For example, if the TIRE AND LOADING INFORMATION label reads 33 psi, then at an elevation of 5,280 ft, the cold inflation pressure using a

gauge should be increased 2.5 psi to 35.5 psi."

NOTE:

In the above example, C-III, Signal Tech II, or the vehicle information display (if equipped) would show a tire pressure of 33 psi. If needed, use

C-III or Signal Tech-II to confirm tire pressure.

NOTE:

^ After correcting the tire pressure, the vehicle may need to be driven at speeds above 16 mph to activate the TPMS and turn off the low tire

pressure warning light.

^ If pressure compensation for temperature is used, the pressure should be rechecked and adjusted at a later time when the tires are cold.

^ If after turning the ignition ON, the TPMS light flashes for one minute and then turns solid, refer to NTB10-048 or NTB09-1O1.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-042 Date: 110420

CVT - Output Speed Sensor Service

Classification: AT11-007

Reference: NTB11-042

Date: April 20, 2011

2007-2011 ALTIMA, JUKE, ROGUE, SENTRA; CVT OUTPUT SPEED SENSOR SERVICE

APPLIED VEHICLES:

2007-2011 Altima (C/L32) QR25 ONLY

2011 Juke (F15)

2008-2011 Rogue (S35)

2007-2011 Sentra (B16) MR20 & QR25 ONLY

SERVICE INFORMATION

If the Output Speed Sensor has been removed and replaced for any reason:

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 316

NOTE:

Input/Turbine Speed Sensor does not require shims. That Sensor is flush mounted to CVT casting.

The correct number of spacer shims must be installed between the Sensor and the CVT body.

Refer above for shim number application chart.

SERVICE PROCEDURE

1. Determine required number of shims by model:

2. Assemble the Output Speed Sensor with the proper 0-ring.

3. Place bolt with attached washers through hole on the Sensor.

4. After determining the correct number of washers for the vehicle, place the shims over the portion of the bolt that is exposed below the sensor

body.

5. Assemble as seen below: Torque retaining bolt to 5.9 Nm (0.6 kg-m, 52 in-lb)

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 317

Wednesday, February 27, 2019

2014 Nissan-Datsun Altima Diagrams. DTC # 10-145 Date: 101215

ABS/TCS - CAN Diagnostic Information

Classification: BR10-011

Reference: NTB10-145

Date: December 15, 2010

ABS / VDC CAN DIAGNOSIS INFORMATION

APPLIED VEHICLES: All 2005-2011 Nissan vehicles with ABS and/or VDC

SERVICE INFORMATION

When diagnosing a vehicle with an ABS or VDC / SLIP warning light on with DTCs stored in the ABS / VDC actuator control unit, perform DTC

diagnosis first.

^ Do not replace the ABS / VDC actuator control unit without being supported by the DTC diagnosis.

^ Do not erase DTCs before performing DTC diagnosis.

^ Always fully diagnose before performing any repairs.

When DTC U1000 (CAN COMM CIRCUIT) is the only DTC stored in the ABS / VDC actuator control unit, use the REPAIR FLOW CHART

below. This will assist in proper diagnosis results and repairs in addition to using diagnostic information in the Electronic Service Manual (ESM).

^ If DTC U1000 is found stored in other systems, refer to NIB10-066 and the applicable ESM.

^ If other DTCs are found stored in ABS / VDC along with U1000, follow the diagnosis steps for those DTCs in the applicable ESM.

CLAIMS INFORMATION

Refer to the current Nissan Warranty Flat Rate Manual and use the appropriate claims coding for repairs performed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 334

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 335

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-106 Date: 100910

Antitheft System - NATS Security VBC Logic

Classification: EL10-028

Reference: NTB10-106

Date: September 10, 2010

NATS SECURITY - VBC LOGIC

APPLIED VEHICLE: 2009 - 2011 All Nissan with NATS / Immobilizer System

SERVICE INFORMATION

All model year 2009 - 2011 Nissan vehicles equipped with NATS/Immobilizer system have the new VBC (Validate Before Crank) starter relay

logic.

VBC (Validate Before Crank) Logic:

^ The BCM will make sure that a valid (registered) key is being used before engaging the starter relay. If the key is not authenticated the starter will

not operate.

^ If the engine cranks, the issue is not related to NATS. Do not replace NATS components (BCM, I-Key, FOB Reader or RF Receiver). Refer to

ASIST for further diagnostic information as needed.

Tuesday, February 26, 2019

2014 Nissan-Datsun Altima Diagrams. DTC # 10-079 Date: 100621

Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.

Classification: EC10-017

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252

Reference: NTB10-079

Date: June 21, 2010

MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED

APPLIED VEHICLES: 2002 and later Nissan vehicles

IF YOU CONFIRM

The MIL is "ON" with P0128 (Thermostat Function) stored.

ACTIONS

1. Check to see if an aftermarket remote starter system is installed.

^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.

2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.

3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-013 Date: 110215

Interior - A-Pillar Trim Removal/Installation Procedure

Classification: BT11-003

Reference: NTB11-013

Date: February 15, 2011

2010 - 2011 ALTIMA; FRONT PILLAR FINISHER REMOVAL

APPLIED VEHICLE: 2010-2011 Altima Sedan (L32)

2010-2011 Altima Hybrid (L32HV)

NOTE:

Does not apply to Altima Coupe

SERVICE INFORMATION

If either one or both front pillar finishers has to be removed for any reason, refer to REPAIR PROCEDURE.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 232

SERVICE PROCEDURE

Remove Front Pillar Finisher

IMPORTANT

1. Remove the front body side welt (see Figure 1).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 233

2. Snap loose both clips by carefully prying with a suitable tool where shown in Figure 2.

CAUTION:

The lower clip will not completely snap loose. Attempting to completely snap loose by force may damage the finisher. Continue to Step 3 for proper

removal.

3. Unfasten the lower clip from the front pillar finisher (finisher) with a suitable tool. See Figure 3 and 4.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 234

4. Tip the top of the finisher inward, and then pull out (see Figure 5).

5. Remove the lower clip from the "A" pillar by pinching and then flipping upward (see Figure 6).

Re-install Front Pillar Finisher

1. Insert the lower clip on the finisher (see Figure 7).

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 235

2. Re-install the finisher by inserting its locator tabs into their slots (see Figure 8 and 9).

3. Align the lower and upper clips into their slots, and then press both into place (see Figure 10).

4. Re-install the front body side welt.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-150 Date: 101222

CVT Controls - MIL ON/DTC P1778/Poor Acceleration

Classification: AT10-010

Reference: NTB10-150

Date: December 22, 2010

2010 ALTIMA, ROGUE, AND SENTRA

MIL IS ON AND/OR SLOWER THAN NORMAL ACCELERATION

APPLIED VEHICLES:

2010 Altima Sedan (L32) with QR25 engine

2010 Altima Coupe (CL32) with QR25 engine

2010 Sentra (B16) with MR20 or QR25 engine

2010 Rogue (S35)

IF YOU CONFIRM

The vehicle has slower than normal acceleration from a stop at times,

and/or

The customer describes the vehicle has slower than normal acceleration from a stop at times,

NOTE:

The condition of slower than normal acceleration from a stop, if it should occur, happens more commonly when the vehicle has been driven for

extended periods at highway speeds.

and/or

The MIL is ON with DTC P1778 (STEP MOTOR) stored in Engine and/or Transmission.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 329

and/or

Only for Sentra without ABS; MIL is ON with DTC P0720 (OUTPUT SPEED SENSOR) stored in Engine and/or Transmission.

ACTIONS

1. Replace the transmission control valve assembly (valve body).

2. Reprogram the TCM (which includes TCM initialization).

^ Refer to Step 2 under TCM reprogramming in the SERVICE PROCEDURE to confirm TCM reprogramming applies and is needed for the vehicle

you are working on.

IMPORTANT:

The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing the repair.

PARTS INFORMATION

CLAIMS INFORMATION

Control Valve Assembly Replacement

1. Replace the CVT control valve assembly.

^ Use the new control valve assembly listed in the Parts Information.

^ Refer to the Transmission section in the appropriate Service Manual for control valve assembly replacement information.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 330

^ Make sure TCM initialization is performed (separately or as part of the TCM reprogramming).

NOTE:

^ The transmission does not need to be removed for this procedure.

^ Transmissions are vulnerable to particles (dust, metal, lint, etc.).

^ When replacing a valve body, make sure your work environment (shop, workbench, etc.), the transmission area (sub-frame, oil pan, harness

connector, etc.), and your hands are free of contamination.

^ Make sure all parts are clean prior to installing on the vehicle. Unpack Service Parts just before installation.

TCM Reprogramming

TCM Reprogramming (includes TCM initialization)

1. Connect CONSULT III (C-III) to the vehicle to begin the reprogramming procedure.

CAUTION

2. When you get to the TCM Reprogramming screen shown in Figure 1, confirm TCM reprogramming applies as follows:

A. On your C-III screen, look at the Part Number column (see Figure 1 example).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 331

^ If this column is blank (no part number listed), this TCM reprogramming does not apply or has already been done. Skip to "TCM Initialization

Procedure (If not done as part of TCM reprogramming) and perform TCM initialization.

^ If a part number (P/N) is listed, write it on the Repair Order and then go to Step B.

B. Compare the P/N you wrote down to the P/Ns in the Current TCM P/N column in Table A above.

^ If there is a match, TCM reprogramming applies. Continue with the reprogramming procedure.

NOTE:

If there are two lines (two reprogramming options) on your C-III screen, use the one that does not have the message "Caution! Use ONLY with

NTBXX-XXX".

^ If there is not a match, TCM reprogramming does not apply or has already been done. Skip to "Perform TCM Initialization".

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 332

3. If TCM reprogramming applies and you have performed TCM reprogramming; when reprogramming is complete, the screen in Figure 2 appears.

Print the page from C-III (C-III page example above) and attach it to the Repair Order for Warranty documentation.

4. Make sure TCM initialization is performed as part of the TCM reprogramming procedure.

5. Make sure to erase DTCs from all systems.

NOTE:

During reprogramming, DTCs will set in several systems and must be erased.

6. Test drive the vehicle and confirm the incident is resolved.

TCM Initialization Procedure

TCM Initialization Procedure (if not done as part of TCM reprogramming)

NOTE:

If reprogramming is not performed, make sure TCM initialization is performed as part of the control valve assembly replacement.

1. Set the parking brake with the selector lever in "P" (Park).

2. C-III and the Vehicle Interface (VI) should still be on and connected, and the vehicle ignition turned ON (engine OFF - not running).

3. Navigate C-III screens to Transmission, then Special Functions.

4. Select the TCM part number (P/N) and Calibration Data, and then print and save a copy.

5. Perform the initialization (EEPROM erase) procedure as follows:

a. Select Transmission Self Diagnostic Results.

b. Shift the selector lever to "R" (Reverse).

c. Press and hold the brake pedal.

d. Press and hold the accelerator pedal down about one-third, but no more than halfway. The purpose of this step is to get both the wide open

throttle and closed throttle position signals to read "OFF" at the same time.

e. Press Erase.

f. Shift the selector lever to "P" (Park).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 333

g. Turn the ignition OFF.

h. Wait 5 seconds.

I. Turn the ignition ON.

6. Select and print the TCM P/N and Calibration Data again.

7. Compare the values between the first and second Calibration Data prints.

^ The procedure is complete if the values are different.

8. Make sure to erase DTCs from all systems.

Monday, February 25, 2019

2017 Nissan-Datsun Altima Technical Service Bulletin # 12-075 Date: 120914

Interior - Rattle Noise From Front Door Panels

Classification: BT12-008

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 75

Reference: NTB12-075

Date: September 14, 2012

2009-2012 ALTIMA SEDAN;

RATTLE NOISE FROM FRONT DOOR PANEL(S)

APPLIED VEHICLES: 2009-2012 Altima Sedan (L32)

APPLIED VINS & DATES:

2009 vehicles built after: 1N4(*)L21(**)9C 165197 // Jan. 21, 2009

1N4(*)L21(**)9N 477825 // Jan. 21, 2009

2010-2011 vehicles: All

2012 vehicles beginning with 1N4(*)L2A(**)CC: All

2012 vehicles built before: 1N4(*)L2A(**)CN 558951 // April 17, 2012

IF YOU CONFIRM

A rattle noise coming from the speaker/pocket area of the front door panel(s) can be heard while audio is playing.

ACTION

1. Remove both front door panels (finishers).

2. Confirm the position of two (2) foam blocks and adjust as needed.

3. Confirm the position of the speaker grill foam strip and adjust as needed.

4. Clean the rim of the door panel.

5. Cut an EPT foam seal (listed in Parts Information) in half, and apply one (1) half to each door panel.

6. Confirm the front speaker screws are properly tightened.

NOTE:

This incident, if it should occur, may sound like a speaker-related issue. Perform the Service Procedure in this bulletin before performing

other repairs (if needed), such as replacing a speaker.

IMPORTANT:

The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire

Service Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

NOTE:

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 76

^ Perform the following steps for both front door panels (driver and passenger side).

^ Images shown in this procedure are of the driver side panel. The process for the passenger side is a mirror image.

1. Remove the front door panel (finisher).

^ Refer to the INT section of the applicable Electronic Service Manual (ESM) for front door panel removal information.

2. Lay the door panel face-down on a clean, flat work surface.

NOTE:

Cover the work surface with a clean cloth fender cover (or other suitable protector) to prevent staining or damage to the door panel face.

3. Check the location of the two (2) foam blocks shown in Figure 1, above.

If the foam blocks are:

^ in the locations shown in Figure 1, or

^ missing

....proceed to step 4.

NOTE:

Do not replace missing foam blocks.

If a foam block(s) is:

^ out of place

....reattach the foam block(s) to the proper location(s), then proceed to step 4.

NOTE:

Use Figure 1 as a reference when reattaching the foam block(s).

4. Check the position of the foam strip applied to the door speaker opening.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 77

^ If the foam strip is centered on the rib and the ends meet (Figure 2), proceed to step 5.

^ If the foam strip is not centered on the rib and/or the ends do not meet (Figure 3), reattach the foam strip to the proper location (Figure 2).

Then, proceed to step 5.

NOTE:

If needed, use a general trim adhesive to reattach the foam strip.

5. As indicated in Figure 4, use isopropyl alcohol to clean the rim of the door panel.

6. Cut an EPT foam seal (listed in Parts Information) in half.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 78

NOTE:

You will use one half of the foam seal on each door.

7. Apply one (1) half of the foam seal to the rim of the door panel.

a. Starting at the edge of the lower foam block, press the EPT foam seal down onto the rim.

NOTE:

If the lower foam block is missing, start the foam seal in the center of the "dip" in rim. See Figure 6.

b. Continue pressing down the foam seal, following the contour of the door panel.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 79

7. Confirm the three (3) front speaker screws are properly tightened.

8. Reinstall the door panel in reverse order of removal.

^ Refer to the INT section of the applicable ESM for door panel installation information.

9. Recheck for the rattle noise. If the rattle noise is still present, refer to ASIST and the applicable ESM for further diagnostic information.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-068E Date: 130128

Campaign P0337 - Navigation Software Update For Various Issues

Reference:

NTB10-068e

Date:

January 28, 2013

VOLUNTARY SERVICE CAMPAIGN

NISSAN NAVIGATION SOFTWARE UPDATE

This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions

of this bulletin.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 506

CAMPAIGN ID #: P0337

APPLIED VEHICLES:

2010 Altima Sedan, Coupe, and Hybrid (L32, CL32, and L32HV)

2010 Maxima (A35)

2010 370Z Coupe and Roadster (Z34 and HZ34)

2011 GT-R (R35)

Check Service Comm to confirm campaign eligibility.

INTRODUCTION

On the Applied Vehicles listed above, the navigation, mobile phone, and iPod(R) functions may not be working as intended. To remedy this

potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor.

IDENTIFICATION NUMBER

Nissan has assigned identification number P0337 to this campaign. This number must appear on all communications and documentation of any

nature dealing with this campaign.

DEALER RESPONSIBILITY

Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private

parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.

REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE

^ Discs 1/3 and 2/3 of the set shown in Figure A are used for all applied models in this campaign except GT-R.

^ Do not use disc 3/3.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 507

^ This NEW disc (Figure B) is required for all applied models in this campaign.

^ This disc replaces disc 3/3 above.

^ This disc also replaces disc NTB10-125b/NTB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.

NOTE:

Numbers on these discs do not match this bulletin's reference number or the campaign ID #.

^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.

^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number

1-(800) 347-8933. Request a new disc using the information printed on the disc.

CLAIMS INFORMATION

Submit a Campaign (CM) line claim using the claims coding:

Service Procedure

IMPORTANT:

Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function otherwise the Navigation System may continuously reboot the

next time it is turned on.

NOTE:

This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to

a low charge rate (trickle charge).

This SERVICE PROCEDURE contains three sections:

A. Disable Bluetooth(R) Function

B. Loading the Program - all except GT-R

Loading the Program for GT-R

C. Check Bluetooth(R) Setting - all except GT-R

Check Bluetooth(R) Setting for GT-R

A: Disable Bluetooth(R) Function

1. Set the parking brake.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 508

2. Turn the ignition ON and keep the transmission in Park or Neutral.

3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

4. Press the "SETTING button on the switch panel.

5. Touch "Bluetooth".

6. Make sure Bluetooth is OFF.

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is OFF when the ON indicator is "grayed-out".

7. Turn the ignition OFF and wait for 10 seconds.

8. Go to B: Loading the Program.

B: Loading the Program - all except GT-R For GT-R.

NOTE:

This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to

a low charge rate (trickle charge).

1. Turn the ignition ON - keep the transmission in Park or Neutral.

^ The navigation start-up screen should display.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 509

NOTE:

If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

4. Select "Navigation Version" on the display screen.

5. Check "Map Version".

^ If the Map Version is 09-10 MAP No. 1 or 09-10 MAP No.1a

a. Continue with Step 6.

^ If the Map Version is any other then above:

a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD/DVD player.

The other Discs will not be needed.

b. Skip to step 18.

6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

7. Insert disc ITB10-031 / NTB1-0068 (Disc 1/3) into the in-dash CD/DVD player.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 510

^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.

IMPORTANT:

Once reprogramming has started:

^ Do not eject a disc while it is loading.

^ Do not change the ignition position until all discs have been loaded.

^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.

8. Wait for the program to load (progress bar will display).

9. When the program has finished loading:

^ Disc will automatically eject, and

^ "Program loading is completed" will display.

10. Carefully remove the disc.

11. The navigation system will automatically restart.

12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).

13. Touch "DVD update".

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 511

14. Touch "Yes" to begin the map update process.

^ Map update will take about 15 minutes.

15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.

16. The navigation system will automatically restart.

17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).

18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:

^ If the screen in Figure 13 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Go to C: Check Bluetooth(R) Setting.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 512

^ If "Now preparing loading" shown in Figure 14 is displayed, reprogramming will begin automatically.

> Follow the on-screen Caution during the reprogram.

19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure 15)

^ Rewriting program data (Figure 16)

^ Rewriting language data (Figure 17)

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 513

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

20. When the first part of the program has finished loading:

^ "Program loading is completed" will be displayed (Figure 18).

^ The Re-programming Software DVD will automatically eject.

21. Remove the DVD and continue to the second part of the update (step 22).

22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 25 on the next page.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 514

23. "Rewriting boot data (Figure 20) and "Rewriting program data (Figure 21) will be displayed.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

24. After the reprogram has completed:

^ "Program loading is completed will be displayed (Figure 22).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 25.

After Navigation has restarted:

25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD

slot again.

One of the following screens will display:

^ If Figure 23 is displayed, it indicates that the reprogram has been completed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 515

> If complete, go to step 26.

^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 18.

> Follow steps 18 through 25 again.

26. Eject the DVD.

27. Go to C: Check Bluetooth(R) Setting.

C: Check Bluetooth(R) Setting (all except GT-R)

1. Press the "Setting button on the switch panel.

2. Touch "Bluetooth".

3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is ON when the ON indicator displays in orange.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 516

^ Bluetooth is OFF when the ON indicator is "grayed-out".

4. Turn the ignition OFF. The process is complete.

B: Loading the Program for GT-R

1. Turn the ignition ON.

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

5. Load the new disc "NTB12-070/ITB12-054 Re-programming Software DVD into CD slot of the audio unit.

One of the following screens will display:

^ If the screen in Figure A1 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Go to Check Bluetooth(R) Setting for GT-R.

^ If "Now preparing loading" shown in Figure A2 is displayed, reprogramming will begin automatically.

> Follow the on-screen Caution during the reprogram.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 517

6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure A3)

^ Rewriting program data (Figure A4)

^ Rewriting language data (Figure A5)

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

7. When the first part of the reprogram has finished loading:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 518

^ "Program loading" is completed will be displayed (Figure A6).

^ The Re-programming Software DVD will automatically eject.

8. Remove the DVD and continue to the second part of the update (step 9).

9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 12.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 519

10. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

11. After the reprogram has completed:

^ "Program loading is completed" will be display (Figure A10).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 12.

After Navigation has restarted:

12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD

slot again.

One of the following screens will display:

^ If Figure A11 is displayed it, indicates that the reprogram has been completed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 520

> If complete go to step 13.

^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 5.

> Follow steps 6 through 12 again.

13. Eject the DVD.

14. Go to C: Check Bluetooth(R) Setting for GT-R.

C: Check Bluetooth(R) Setting for GT-R

1. Press the "Setting button on the switch panel.

2. Touch "Bluetooth".

3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is ON when the ON indicator displays in orange.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 521

^ Bluetooth is OFF when the ON indicator is "grayed out".

4. Turn the ignition OFF. The process is complete.

Sunday, February 24, 2019

2014 Nissan-Datsun Altima Diagrams. DTC # 11-045 Date: 110425

Body - Carpet Wet/Water Leak From Sunroof

Classification: BT11-013

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 311

Reference: NTB11-045

Date: April 25, 2011

ALTIMA AND MAXIMA; SUNROOF FRONT DRAIN HOSE IS KINKED, PINCHED, OR DISCONNECTED

APPLIED VEHICLES:

2007-2011 Altima Sedan (L32)

2008-2011 Altima Coupe (CL32)

2009-2011 Maxima (A35)

SERVICE INFORMATION

A wet carpet or water leaking from the sunroof/headliner may be related to the sunroof drain hoses.

If the front RH or LH sunroof drain hose is found to be kinked or pinched in the lower dash area:

^ Replace the drain hose with a new one.

NOTE:

Follow the standard Electronic Service Manual (ESM) procedures when replacing the front RH or LH sunroof drain hose.

If the front RH or LH sunroof drain hose is found to be disconnected only and not kinked or pinched:

^ Reconnect the drain hose. Do not replace the drain hose.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-062A Date: 120622

Wheels/Tires - Wheel/Tire Balancing Information

Classification: WT11-008A

Reference: NTB11-062A

Date: June 22, 2012

ROAD WHEEL BALANCING WITH HUNTER ROAD FORCE(R) GSP9700 TIRE BALANCER

This bulletin has been amended in the SERVICE INFORMATION section. Tire warm-up time has been increased. Discard all previous versions of

this bulletin.

APPLIED VEHICLES: All Nissan

SERVICE INFORMATION

The most common cause of vehicle vibration at highway speeds is tire/wheel assembly (or road wheel) non-uniformity. There are three primary

contributors that affect tire/wheel assembly vibration:

^ Imbalance

^ Radial run-out

^ Tire Road Force Variation (RFV, or Radial Force Variation)

The Hunter Road Force(R) GSP9700 tire balancer (GSP9700) has the capability to measure tire Road Force Variation (RFV).

When measuring RFV, it is important to look at both the RH1 and RH2 values.

This bulletin will instruct you how to:

^ Prepare the tire/wheel assemblies for balancing on your GSP9700

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 114

^ Measure and display RH1 and RH2

^ Determine if the tire/wheel assemblies are within specified limits

Road Force Variation

Radial Force Variation (RFV) is a measurement term. Tire RFV is a measure of the variation (up and down) of the load action on the spindle, the

force applied to the suspension as the tire turns. This measures the tires uniformity under load.

The primary measures for RFV are 1st harmonic, once per revolution, or RH1, and 2nd harmonic, twice per revolution, or RH2.

Tire/wheel assembly uniformity can only be measured under load.

The GSP9700 measures uniformity by using a load roller. The load roller simulates a load on a tire similar to when it is mounted on a vehicle and

driven on the road.

Most road wheel vibration issues are due to road force variation of RH1 or RH2. Of the two, RH1 is more common.

RH1 vibration causes the road wheel to hop/bump once per revolution. This creates a vibration similar to an imbalance condition.

RH1 can cause steering wheel shimmy or shake, and/or body vibration.

RH1 may be caused by:

^ Imbalance

^ Radial run-out

^ Tire uniformity, or RFV

RH2 can be the primary cause of vibration, although it is not as common as RH1.

RH2 vibration occurs twice per revolution and may be caused by:

^ Radial run-out of tire and/or wheel (i.e., oval or egg shaped)

^ Tire uniformity

Preparing Tire/Wheel Assemblies before Measuring Uniformity (RFV)

1. Check (and adjust as necessary) all tire pressures.

2. Warm up the tires by driving the vehicle a minimum of 15 minutes at highway speeds.

^ This will remove any temporary flat spots prior to testing (refer to NTB11-027).

3. Verify the incident after performing the 15 minute warm-up.

4. If the incident is verified, check uniformity of all tire/wheel assemblies.

Mounting a Tire/Wheel Assembly to a GSP9700

Follow all applicable instructions in the manufacturers operators manual.

Make sure to:

^ Use the correct collet and flange plate (refer to NTB11-044)

^ Check for and remove debris on all road wheels

^ Perform a centering check (to make sure the road wheel is mounted properly on the balancer)

Measuring Tire/Wheel Assembly Uniformity (RFV)

NOTE:

For details regarding measurement of RFV, refer to the manufacturers operators manual.

1. Once properly mounted, spin the tire/wheel assembly.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 115

2. Without measuring Rim Run-out:

a. Using the menu shift key, navigate to and select "Show Runout & ForceMatching" (see Figure 1).

b. From the "Current Runout & Road Force" screen above, select "Show Details" (see Figure 2).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 116

c. "Assembly Road Force" will display (see Figure 3).

^ See value for "R2H" (RH2).

RH1 Above Limit

If RH1 is above the applied limit shown in the table below, perform the following.

1. Mark the tire at the high spot of RFV, and then at the same location on the wheel (see Figure 4).

^ This will be the reference point to the original indexed location.

2. Deflate the tire, and then break down both beads from the wheel.

3. Rotate the tire 180 degrees on the rim.

4. Seat both beads (refer to NTB11-029), and then inflate the tire to its specified pressure.

5. Measure RFV again.

6. Mark the second high spot of RFV.

a. If the second tire mark is within 4 inches of the first of RFV tire mark and RFV is still over the guidelines listed below, the root cause is

most likely the tire.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 117

b. If the second tire mark is within 4 inches of the mark on the wheel and RFV is still over the guidelines, the root cause is most likely the

wheel.

c. If the second tire mark is still over the guidelines and did not locate where stated in 6a or 6b:

> Runout can likely be improved by rotating the tire and its second mark another 90 degrees in the direction of the first mark.

RH2 Above Limit

If RH2 is above the applied limit shown in the table below, replace the tire.

Example of typical RH value settings (Some Vehicles May Require Lower Settings)

Refer to NTB11-054 for further details.

2014 Nissan-Datsun Altima Diagrams. DTC # 09-131A Date: 110815

Vehicle - Certification Label/VIN Plate Replacement

Classification: BT09-020A

Reference: NTB09-131A

Date: August 15, 2011

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT

This bulletin has been amended. Please discard previous versions of this bulletin.

APPLIED VEHICLES: All Nissan

SERVICE INFORMATION

Because of collision damage or other vehicle repair, a replacement "Certification Label or "VIN Plate/Label" may be needed.

NOTE:

Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label.

These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for

such replacements.

^ The "VIN Plate/Label" (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see

Figure 1).

^ The "Certification Label" (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

CERTIFICATION LABEL REPLACEMENT CRITERIA

NOTE:

See "Replacement VIN plate/label" below.

A replacement Certification Label may be requested ONLY if the vehicle is in a collision and:

^ The Certification Label is damaged, or

^ The Certification Label is attached to a part that will be replaced during the repair.

REQUESTING A REPLACEMENT CERTIFICATION LABEL

1. Take a photo of the original Certification Label in its original location on the vehicle B pillar.

^ A photo of the original Certification Label before it is removed must accompany the application; or processing will be significantly delayed or

rejected.

^ If the vehicle is produced outside of the U.S. and a legible Certification Label photo is not provided, the request will be rejected.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 246

^ If the vehicle is produced in the U.S. and is greater than 60 days old and a legible Certification Label photo is not provided, the request will be

rejected.

2. Completely fill out a copy of the APPLICATION FOR REPLACEMENT CERTIFICATION LABEL shown above.

3. Remove the original Certification Label from the vehicle and attach in the designated area on the application form.

^ Processing will be significantly delayed or rejected if the original Certification Label is not available (or a legible photo).

4. Staple the photo of the original Certification Label (in its original location) to the application form.

5. Mail (DO NOT FAX) the completed application with the photo of the label to your Regional Office: Attention: Replacement Certification and

VIN Plate Request.

NOTE:

Your dealer "Non Vehicle Account" will be billed $25.00 for each replacement label.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 247

NOTE

VIN PLATE/LABEL REPLACEMENT CRITERIA

APPLICATION FOR REPLACEMENT VIN PLATE/LABEL

NOTE

Refer to "Replacement Certification Label"

A replacement VIN plate/Label may be requested ONLY if:

^ The vehicle is in a collision and the VIN plate/label is damaged.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 248

^ The vehicle was recovered after being stolen and the VIN plate/label is damaged but still available.

REQUESTING A REPLACEMENT VIN PLATE / LABEL

1. Completely fill out a copy of the APPLICATION FOR REPLACEMENT VIN PLATE / LABEL.

2. Remove the original VIN plate/label from the vehicle and attach in the designated area on the application form.

^ The original VIN plate/label MUST accompany the application.

^ For a VIN label that will destroy itself when removed:

> A photo of original instrument panel VIN Label must accompany the application

> A photo of the Certification label (on the B-pillar) clearly showing the VIN must also accompany the application.

^ Stolen VIN plate/label:

> If a VIN Plate/Label is stolen, contact the appropriate State Police or State Department of Motor Vehicles (DMV). In most cases, the State

DMV will issue a unique VIN so the original VIN can be included on stolen vehicle listings. If this is the case, a replacement VIN

plate/label is NOT available from Nissan. However, the original VIN, not the state issued VIN, must be used on all warranty claims.

3. Mail (DO NOT FAX) the completed application with the photo of the label to your Regional Office: Attention: Replacement Certification and

VIN Plate Request.

NOTE:

^ Your dealer "Non Vehicle Account" will be billed $25.00 for each replacement VIN plate/label.

^ All replacement VIN plates/labels are subject to approval by the Technical Compliance Department. If you have any specific questions,

contact your Owner Relations Manager (ORM).

Saturday, February 23, 2019

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-140 Date: 091208

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 392

A/T - CVT Oil Leak Diagnosis Information

Classification: AT09-012

Reference: NTB09-140

Date: December 8, 2009

CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE

APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)

SERVICE INFORMATION

If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.

1. Thoroughly clean off the area of the suspected leak.

2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.

3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).

4. Inspect with lamp from J-43926 A/C Dye Kit*

If no fluorescent oil trace/leak is found, the stain is probably:

^ corrosion protection chemicals sprayed on the transmission

and/or

^ lubricants which are sometimes used to ease the assembly process.

NOTE:

These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.

If a fluorescent oil trace/leak is found:

^ Repair using standard warranty procedures.

*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.

NOTE:

The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.

Nissan IMs Concept - interior Exterior (Elevated Sports Sedan)

Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news

2014 Nissan-Datsun Altima Diagrams. DTC # 12-070A Date: 130305

Audio/Navigation System - Various Issues

Classification: EL12-060A

Reference: NTB12-070A

Date: March 5, 2013

2010 - 2014; NAVIGATION SYSTEM REBOOTS OR AUDIO CONTROLS WILL NOT RESPOND

This bulletin is being amended to update the Applied Vehicles information.

Please discard previous versions of this bulletin.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 538

APPLIED VEHICLES

IF YOU CONFIRM

One or more of the following is occurring on an Applied Vehicle:

^ Specific addresses cannot be entered

^ System reboots when:

> On long trips with a destination set

> Within a few minutes of starting the vehicle

^ A destination set or during the process of setting

> The logo appears after the system shuts off

^ System locks up with many functions occurring at one time (USB, Bluetooth, MP3, vehicle in reverse/camera operating, etc.).

^ POIs are missing (Application disc of new "map update" was not installed).

^ Popping noise from the vehicles speakers when ignition is turned on after entering the vehicle, if the customer was on a Bluetooth Handsfree call

that connected to the vehicle mid call.

NOTE:

Do not install this software update for Bluetooth Sound Quality concerns. Refer to bulletins NTB09-063, NTB12-105 or NTB12-106 to resolve.

^ Incoming call cannot be heard or received when using iPhone 5.

ACTION

^ Follow the Service Procedure to load the Re-programming Software DVD referenced in the Parts Information.

NOTE:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 539

iPhone 5 "Incoming call cannot be heard or received" can also be resolved independently with the latest Apple iOS (phone operating system) update.

Please have customer update their iPhone: Settings>General>Software Updates.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

NOTE:

This procedure will take 10-20 minutes with the ignition ON and will require the DVD to be inserted twice to complete the update.

^ Before starting the procedure, make sure to attach a battery charger to the vehicle battery and set it to a low charge rate (trickle

charge).

1. Set the parking brake.

2. Turn the ignition ON and keep the transmission in Park or Neutral.

^ The Navigation start-up screen should display.

^ If the Navigation start-up screen is not displayed: turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.

3. Wait more than 1 minute.

4. Turn the Bluetooth OFF.

5. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

6. Load "NTB12-070/ITB12-054 Re-programming Software" DVD into CD slot of the audio unit.

^ For Altima, press the OPEN/TILT button to open the display and access the CD/DVD player slot. Leave the display open while loading.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 540

^ If the screen in Figure 1 is displayed, this update has already been performed and this bulletin does not apply.

> Turn the Bluetooth back ON and remove the DVD from the CD slot.

^ If "Now preparing loading" shown in Figure 2 is displayed, follow the on screen Caution while the Navigation is updated.

7. During the first part of the update process 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure 3)

^ Rewriting program data (Figure 4)

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 541

^ Rewriting language data (Figure 5)

IMPORTANT:

Once the re-programming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

8. When the first part of the program has finished loading:

^ "Program loading is completed" will be display (Figure 6).

^ The Re-programming Software DVD will automatically eject.

9. Remove the DVD and continue to the second part of the update in step 10.

10. After the DVD is removed, the screen in Figure 7 "Please insert disc" may ask to reinstall the same Re-programming Software DVD for a

second time.

^ If not, the re-programming is complete. Proceed to step 13.

^ If so, re-insert DVD disc.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 542

> At the top of the screen "Program Loading (2nd)" will be displayed.

11. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.

IMPORTANT:

Once re-programming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

12. After the reprogram has completed:

^ "Program loading is completed" will be display (Figure 10).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart.

^ Proceed to step 13.

After Navigation has restarted:

13. To confirm that the Navigation version has been successfully updated, load the DVD into the CD slot for a third time.

^ If Figure 1 is displayed it indicates that the re-program has been completed.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 543

> If complete go to step 14.

^ If Figure 2 is displayed, allow the update to complete (steps 7-12) and follow the on screen instructions, then perform step 13 to confirm

the re-program has completed.

14. Eject DVD.

15. Turn the Bluetooth back on.

16. The procedure is complete. Turn the ignition OFF.

Friday, February 22, 2019

2014 Nissan-Datsun Altima Diagrams. DTC # 07-095D Date: 111003

Interior - Driver Seat Power Lumbar Support Inoperative

Classification: BT07-029D

Reference: NTB07-095D

Date: October 3, 2011

2007-2012 ALTIMA;

DRIVER SEAT LUMBAR SUPPORT REPAIR PROCEDURE

The Applied Vehicles section of this bulletin has been amended. No other changes have been made. Please discard any previous versions of this

bulletin.

APPLIED VEHICLES:2007-2012 Altima Sedan and Hybrid

(L32 and L32HV)

IF YOU CONFIRM

The power lumbar support on the driver seat is inoperative.

ACTION

Replace the lumbar support assembly.

^ Do not replace the entire seatback for this incident.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 212

CLAIMS INFORMATION

IMPORTANT:

The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

Service Procedure

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down the radio station presets.

2. Move / adjust the driver seat bottom and seatback to the full forward positions.

3. Disconnect both 12V battery cables, negative cable first.

4. Remove the driver seatback finisher as follows:

NOTE:

The seatback finisher is held on with:

^ 2 top clips (do not reuse)

^ 2 side hooks

^ 2 bottom hooks

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 213

a. Insert your fingers into the sides of the finisher.

b. Push in on the side hooks to release them.

c. Then carefully pull UP on the bottom to release the bottom hooks.

d. Reach in from the bottom to release the top clips (see Figures 3 and 4).

NOTE:

^ To release the top clips: use needle nose pliers to squeeze the clips at the points shown.

^ Do not reuse the top clips. New clips are included in the repair kit.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 214

5. Unhook the seat trim side hooks.

6. Release the seat trim clips.

7. Remove the 2 side airbag mounting nuts.

^ Side air bag is on the left side of the seat.

^ Do not use a power tool on these nuts.

^ Discard these nuts: DO NOT REUSE. New nuts are included in the repair kit.

8. Locate and remove the 2 left side lumbar support assembly mounting bolts.

^ Carefully move the seat trim, seat foam, and side air bag to the left.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 215

^ Do not damage the side air bag mounting stud threads.

^ The bolts have an 8 mm hex head.

9. Connect both 12V battery cables, positive cable first.

10. Move the seat bottom to the full rearward position.

11. Recline the seatback far enough to access the 2 mounting screws on the right side of the lumbar support assembly.

12. Remove the 2 right side lumbar support assembly mounting bolts.

^ Move the seat trim and seat foam to the right.

^ The bolts have an 8 mm hex head.

13. Remove the lumbar support assembly.

14. Disconnect the lumbar motor harness connector.

15. Connect the harness to the new lumbar motor.

16. Install the new lumbar support assembly into the seatback.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 216

17. Install the 2 mounting bolts on the right side of the lumbar support assembly.

^ Make sure the mounting bracket tab is installed as shown.

18. Move the seat bottom and seatback to the full forward positions.

19. Disconnect both 12V battery cables, negative cable first.

20. Install the 2 mounting bolts on the left side of the lumbar support assembly.

^ Make sure the mounting bracket tab is installed correctly (see Figure 11 above).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 217

21. Install the 2 side airbag mounting nuts.

^ Use new nuts; new nuts are included in the repair kit.

^ Do not use a power tool on these nuts.

^ Torque nuts to:

7.3 N.m (0.74 kg-m, 65 in-lb)

IMPORTANT:

When reinstalling the side air bag, make sure the module is fully inside the white cloth sleeve. Also, make sure the sleeve is smooth and not bunched.

22. Attach the seat trim side hooks.

23. Attach the seat trim clips.

24. Replace the top clips on the seatback finisher.

^ New clips are included in the repair kit.

25. Install the seat back finisher as follows:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 218

^ 1st slide the bottom hooks in place.

^ 2nd align the top clips and push in to secure.

^ 3rd push in to secure the center hooks.

26. Connect the 12V battery cables, positive cable first.

27. Operate the lumbar support. Make sure it is working correctly.

28. Reset the radio station presets.

29. Perform the power window initialization for both front door windows as follows:

a. Turn the ignition ON.

b Open the window-all the way DOWN.

C. Pull all the way UP on the switch and hold.

d. Continue holding the switch all the way UP for 4 seconds after the window is closed.

e. Confirm the window is now operating correctly.

NOTE:

The above initialization procedure must be performed any time the battery is disconnected.

30. If equipped, make sure the sunroof "auto-open/close" functions correctly.

If the sunroof does not open or close automatically, perform the following procedure:

a. Push the tilt up switch and start the tilt up operation.

b. Release the tilt up switch.

c. Press the tilt up switch again and hold it.

d. Keep pressing/holding the switch. The lid will more toward the tilt up direction and stop, and then it will fully close.

e. Release the switch.

f. Within 10 seconds, press the tilt up switch and hold it.

g. Keep pressing/holding the switch. After 4 seconds, the glass lid will be automatically operated in sequence of tilt down, slide open and slide

close.

h. After the glass lid stops, release the switch within 0.5 seconds.

I. Make sure the "auto-open/close" functions correctly.

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-153 Date: 101223

Brakes - Feel More Sensitive Than Expected

Classification: BR10-013

Reference: NTB10-153

Date: December 23, 2010

2010-2011 ALTIMA AND MAXIMA;

BRAKES FEEL MORE SENSITIVE THAN EXPECTED

APPLIED VEHICLES:2010-2011 Altima Sedan & Coupe (L32 & CL32)

2010-2011 Maxima (A35)

APPLIED VINs: 2010 Altima built after:

1N4(*)L2(***)AC 173905 (Smyrna) or 1N4(*)L2(***)AN 527905 (Canton)

2011 Altima built before:

1N4(*)L2(***)BC 105774 (Smyrna) or 1N4(*)L2(***)BN 407818 (Canton)

2010 Maxima built after: 1N4AA5AP(*)AC 862521

2011 Maxima built before: 1N4AA5AP(*)BC 807780

APPLIED DATE Vehicles built between June 9, 2010 and September 21, 2010

IF YOU CONFIRM

The brakes feel more sensitive than expected with light to moderate brake application,

and/or

Towards the end of bringing the vehicle to a stop (last few feet), the vehicle stops SLIGHTLY quicker than expected.

ACTION

Replace the Brake Booster Assembly

^ Refer to section BR in the appropriate Service Manual for brake booster replacement information.

^ Use the new brake booster listed in the Parts Information.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 223

2014 Nissan-Datsun Altima Diagrams. DTC # 10-114B Date: 120614

Tire Monitor System - Tire Inflation Information

Classification: WT 10-005B

Reference: NTB10-0114B

Date: June 14, 2012

INFLATING TIRES EQUIPPED WITH TPMS

The publication date on this bulletin has been amended to include the newest models.

APPLIED VEHICLE: All Nissan with Tire Pressure Monitor System (TPMS)

SERVICE INFORMATION

Improper use of tire inflator tools can break the stem of a Tire Pressure Monitor System (TPMS) sensor.

NOTE:

The type of stem breakage shown in Figure 1 is not considered a warrantable repair.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 120

Please refer to the following examples of recommended and not recommended tire pressure filling tools.

Not Recommended tire inflator tools.

Recommended tire inflating tools.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 121

Aftermarket Tire Sealers

Thursday, February 21, 2019

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-078 Date: 120919

Steering - Power Steering Service Information

Classification: ST12-007

Reference: NTB12-078

Date: September 19, 2012

NISSAN; POWER STEERING SYSTEM SERVICE INFORMATION

APPLIED VEHICLES: All 2005 and later Nissan vehicles

equipped with hydraulic rack and pinion steering system

SERVICE INFORMATION

When diagnosing possible power steering leak issues, it is important to follow the Inspection Flow Chart provided in this bulletin.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 71

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 72

^ See example photos above.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 73

Inspection Flow Chart

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 74

Flow Chart A

Fluid Leakage Inspection Preparation

1. Verify the fluid level in the reservoir is within normal cold or hot range, as it applies.

2. Let the engine idle until the fluid temperature is within 50-80锟斤拷C.

3. Turn the steering wheel from full left to full right 30 times.

4. Carefully hold the steering wheel for approximately five (5) seconds in the full (locked) left position, and then the locked right position.

CAUTION:

Do not hold the steering wheel in a locked position for more than 10 seconds. Damage may occur to the power steering pump.

5. Let the engine idle for 10 minutes, and then inspect for leaks.

7 STRANGEST New Engines

2014 Nissan-Datsun Altima Diagrams. DTC # 08-072A Date: 101007

Interior - Rough Driver's Power Seat Operation

Classification: EL08-005A

Reference: NTB08-072A

Date: October 7, 2010

2007-2010 ALTIMA; DRIVERS POWER SEAT SLIDE TRAVEL ROUGH

This bulletin has been amended. The Relevant Vehicles and the Parts Information has changed.

RELEVANT VEHICLES:

2007-2010 Altima (L32)

2007-2010 Altima Hybrid (L32HV)

IF YOU CONFIRM

The driver's power seat slide travel front to back is rough.

ACTION

For all 2010 Altimas and 2009 Altimas built from:

^ 1N4(*)L(*)1E(*)9 C 151712/5-Nov-2008

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 460

^ 1N4(*)L(*)1E(*)9 N 453274/4-Nov-2008

Install the Power Track Service Kit to resolve the issue. Refer to the Service Procedure.

NOTE:

Do not replace the seat bottom or seat lower assembly for this issue, if it should occur.

For 2007 through 2009 Altimas built to:

^ 1N4(*)L(*)1E(*)9 C 151711/5-Nov-2008

^ 1N4(*)L(*)1E(*)9 N 453273/4-Nov-2008

This bulletin does not apply. Replace the Seat Lower Assembly using standard Nissan Warranty Practices.

IMPORTANT:

The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down the radio station presets.

2. Slide the driver's seat fully rearward and remove the front two seat-to-body bolts.

3. Tilt the seat back to the upright position and remove the headrest.

4. Slide the seat mid-travel, raise the seat all the way up, and remove the rear seat-to-body bolts.

5. Disconnect both 12V battery cables, negative cable first, and wait at least 3 minutes before proceeding to step 6.

6. Disconnect the seat harnesses from the body harnesses.

7. Remove the seat from the vehicle.

8. Place the seat, back side down, on a clean covered workbench.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 461

9. Remove the seat bottom plastic side shields.

10. Disconnect the power harness and clip from the track motor.

11. Remove all eight nuts holding the lower seat track to the seat as shown. The lower rack will not be reused.

12. Remove the new track assembly from the shipping package and lay it next to the seat as shown.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 462

13. Set the seat assembly onto all eight studs of the new lower track assembly.

14. Tighten all eight nuts in sequence as shown.

15. Remove the four bolts and the plastic bracket. The plastic bracket will not be reused.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 463

16. Connect the track motor power harness and clip.

17. Reinstall the plastic shields.

18. Reinstall the seat into the vehicle, reconnecting the seat harnesses to the body harnesses while doing so.

IMPORTANT:

Be sure that all Side Air Bag harnesses are routed correctly and that all connectors are firmly seated.

19. Install the four seat-to-body bolts in the sequence shown in Figure 7

TORQUE: 40 Nm (3.9 kg-m, 35 ft-lb).

20. Reinstall the headrest.

21. Reconnect the battery cables.

22. Check seat for proper operation.

23. Reprogram the radio presets.

24. Reinitialize power windows and other systems as needed.

Wednesday, February 20, 2019

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-048B Date: 111003

Keyless Systems/TPMS - SIGNAL TECH II(R) Diag. Tool

Classification: WT10-001B

Reference: NTB10-048B

Date: October 3, 2011

SIGNAL TECH II DIAGNOSTIC TOOL

This bulletin has been amended. The note below APPLIED VEHICLES was amended. Please discard previous versions of this bulletin.

APPLIED VEHICLES: All Nissan with Tire Pressure Monitor System (TPMS), Remote Keyless Entry, or Intelligent Key.

NOTE:

Failure to update Signal Tech II may lead to misdiagnosis of certain models.

^ The latest software is available on the CONSULT III PC at: ASIST> Specialty Tools > Signal Tech II

^ If you should encounter problems updating Signal Tech II, contact Techmate.

^ Future updates will be released as needed. Check ASIST frequently for this information.

SERVICE INFORMATION

If service is required on a vehicle's Tire Pressure Monitor System (TPMS), remote keyless entry, or Intelligent Key, the Signal Tech II (special tool

J-50190) can be used for diagnostics.

Signal Tech II will quickly:

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 207

^ Activate and display TPMS Sensor IDs

^ Display tire pressure reported by the TPMS sensor

^ Read TPMS DTCs and register TPMS IDs

^ Store and print reports for warrantable repairs

^ Check Intelligent Key relative signal strength

^ Test remote keyless entry relative signal strength

^ Confirm vehicle Intelligent Key antenna relative signal strength output

^ Read ENGINE DTCs

Other available information for Signal Tech II:

^ Signal Tech II Quick Start Guide: ASIST> Tools & Equipment > Tool & Equipment Web Page

^ Signal Tech II Users Guide: ASIST > Tools & Equipment> Tools & Equipment Web Page

^ Tool Flyer: ASIST > Tools & Equipment > Tools & Equipment Web Page> Nissan Essential Tool Flyers

^ Tech Talk Article: ASIST > Tech Support Info> TECH TALK / XTRA> Spring 2010 issue

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-015B Date: 130201

Engine - Oil Leakage From The Upper End Of Oil Cooler

Classification:

EM10-002b

Reference:

NTB11-015b

Date:

February 1, 2013

ALTIMA SEDAN AND COUPE, SENTRA, AND ROGUE WITH QR25DE ENGINE; OIL LEAK

This bulletin has been amended in APPLIED VEHICLES, SERVICE PROCEDURE, PARTS INFORMATION, and CLAIMS INFORMATION.

Discard all previous versions of this bulletin.

APPLIED VEHICLES:

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 488

2007 - 2012 Altima Sedan (L32)

2008 - 2013 Altima Coupe (CL32)

2007-2012 Sentra (B16)

2008 - 2013 Rogue (535)

APPLIED ENGINE:

QR25DE (4 cyl)

IF YOU CONFIRM:

Oil is leaking from the upper end of the engine oil cooler (oil cooler). See Figure 1.

ACTION:

Reseal the oil cooler with the parts listed in the PARTS INFORMATION.

^ For repairs refer to SERVICE PROCEDURE.

NOTE:

Do not replace the complete engine oil cooler assembly for this incident if it should occur.

IMPORTANT:

The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE

PROCEDURE as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 489

CLAIMS INFORMATION

SERVICE PROCEDURE

1. Remove the oil cooler from the engine block.

^ Refer to the appropriate section of the Electronic Service Manual (ESM) if needed.

^ Perform repairs in a clean work environment.

2. Remove the four (4) bolts, and then remove the upper half of the oil cooler. See Figure 2.

3. Remove the O-ring gasket, and then thoroughly clean out the gasket area and around it with a suitable cleaner.

^ The dashed line in Figure 3 shows the O-ring gasket area to be cleaned.

^ Make sure no debris or contaminants get into the holes.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 490

^ Also clean underneath the upper half of the oil cooler (no picture shown).

4. Lightly coat the new O-ring gasket (see PARTS INFORMATION) with engine oil, and then put it in place. See Figure 4.

5. Install the upper half of the oil cooler with the bolts.

6. Torque the bolts in two steps: first step at half value, and then the second step at full value (listed below).

^ Bolts torque sequence:

1-2-3-4-5-6-7-8 (see Figure 5).

^ Bolts torque:

4.0 N.m (0.41 kg-m, 35.4 in lb)

7. Install the oil cooler to the engine with a new gasket (see PARTS INFORMATION).

Refer to the appropriate section of the ESM if needed.

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-024A Date: 100318

Wipers/Washers - Windshield Washer Repair

classification: EL09-026A

Reference: NTB10-024A

Date: March 18, 2010

2007 - 2010 ALTIMA; WINDSHIELD WASHER REPAIR

This bulletin has been amended. The Parts Information was corrected. No other changes were made. Please discard previous versions.

APPLIED VEHICLES:

2007-2010 Altima (L32, CL32, & L32HV) Sedan, Coupe & Hybrid

SERVICE INFORMATION

Separate service parts are now available for the windshield washer tank assembly.

When performing service on the windshield washer system, perform diagnostic procedures to determine if only a tank, motor, or sensor is needed.

Do not replace the entire assembly when only tank, motor, or sensor will solve the issue, if one should occur.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 413

PARTS INFORMATION

CLAIMS INFORMATION

Reference the current Nissan Flat Rate Manual and use the appropriate claims coding.

Tuesday, February 19, 2019

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-009 Date: 110209

Interior - Front Seat Side Finisher Removal Procedure

Classification: BT11-002

Reference: NTB11-009

Date: February 9, 2011

2007 -2011 ALTIMA SEDAN;

FRONT SEAT SIDE FINISHER REMOVAL

APPLIED VEHICLES:

2007-2011 Altima Sedan (L32)

2007-2011 Altima Hybrid (L32HV)

IF YOU CONFIRM

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 326

^ A front seat outboard side finisher needs to be removed for any reason.

ACTION

Follow the Service Procedure in this bulletin for removal.

IMPORTANT:

The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

SERVICE PROCEDURE

1. Remove adjustment knobs or lever (see Figures 2 and 3).

^ For manual seat - remove the adjustment lever

^ For power seats - remove the adjustment knobs.

If needed, use a plastic trim tool.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 327

2. Remove the screw at the rear of the finisher.

3. Insert a clean medium size flat blade screw driver between the seat cushion and the finisher as shown in Figure 5.

4. Release metal clip by pushing on the finger (see Figure 6).

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 328

5. Unsnap/unclip the rest of the finisher as shown in Figure 7.

2014 Nissan-Datsun Altima Diagrams. DTC # 08-097F Date: 111121

Steering/Suspension - Pull Or Drift Diagnostic Info

Classification: ST08-001F

Reference: NTB08-097F

Date: November 21, 2011

DIAGNOSIS OF VEHICLE PULL (DRIFT) AND STEERING WHEEL OFF CENTER

The General Procedures linked if you are using a internet copy of this bulletin has been amended. Please discard previous versions of these General

Procedures.

APPLIED VEHICLES: All Nissan - except GT-R

SERVICE INFORMATION

If a customers reports their "vehicle pulls" or the "steering wheel" is off-center, use the Diagnostic Flow Chart above and the other information in

this bulletin to diagnose and correct the issue

Road Test

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 171

Determine if the vehicle has a pull or steering wheel off-center issue that requires repair.

IMPORTANT:

^ If the vehicle has any tire issues, such as:

> Tires that are different sizes (except when specified from the factory)

> Significant difference in the amount of wear between any of the tires

> Any other tire irregularity or damage to any tire

Replace the tire(s) or use known good tires from another vehicle for all road tests and diagnostics in this bulletin.

^ Make sure tire pressure is set to the correct specification.

1. Install the following measuring tools on the vehicle:

^ Steering Wheel Offset Gauge

^ Road Crown Gauge

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 172

NOTE:

Refer above for a description of these tools and an explanation of their use.

2. Obtain a watch with a second hand (preferably a stopwatch) to use during the road test.

3. Take the vehicle for a road test and confirm the customers concern.

^ Select a flat road where the vehicle can be driven in a straight line at a preferred speed of 60 mph.

^ During the road test make sure the vehicle is pointing straight. Don't worry about steering wheel position during the road test.

NOTE:

^ If you adjusted the tire pressure or changed the tires before the road test, the issue may have been resolved.

^ If there are cross winds strong enough to affect the vehicle's straight line movement, then diagnosis cannot be performed.

4. Determine the vehicles issue - refer to the definitions of "Pull" and "Steering Wheel Off-center".

5. When the road test is completed, remove the Road Crown Gauge, leave the Steering Wheel Off-Set Gauge in place until the Service Procedure is

complete.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 173

6. Refer to the Flow Chart for the next step.

Other Service Information

Customers may report that their vehicle's steering wheel is "off-center" because the steering wheel spokes are tilted to the left or right when the

vehicle continues straight ahead on a straight flat road (see example in Figure 1).

If a vehicle's steering wheel spokes are slightly off center while driving straight, it may be the normal result of road crown. Most roads in the United

States are built with a "crown" to help rain water drain from the road surface. The slope of the road crown varies from place to place.

Vehicles have a natural tendency to drift to the low side of the crown. The greater the slope of the crown, the faster the vehicle will drift in that

direction.

Tires and vehicles are designed to counteract the effect of typical road crown, but may not fully counteract the effect of a highly crowned road.

Some freeways slope to both the left and right from the center. When driving on a freeway that slopes in both directions, a vehicle may exhibit a

small amount of drift to the left when driving in the left lane and a small amount of drift to the right when driving in the right lane.

This bulletin does not address road crown issues because they are not vehicle related, although the customer may incorrectly perceive them to be.

Description/Definition of Steering Wheel "Off-center" Condition

The steering wheel spokes are tilted to the left or right more than allowable (see example in Figure 2) when driving straight ahead on a straight flat

road.

Allowable specification for steering wheel off-center

^ All Nissan (except NV1500, 2500, and 3500): 2 mm or less.

^ NV1500, 2500, and 3500: 4 mm or less.

When driving straight on a highly crowned road, the steering wheel may be turned (off-center) to counteract the affect of the road crown. When road

testing for an off-center condition, the vehicle should be driven on a straight flat road.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 174

Although the vehicle does not pull in either direction, the customer may perceive that the vehicle pulls because it will respond if he or she tries to

bring the steering wheel back to center. This condition can occur if the tie rod length is uneven (not adjusted correctly) from side to side.

Description/Definition of a Vehicle "Pull" Condition

The vehicle consistently drifts to one side while driving at a constant speed on a straight, flat road.

^ A vehicle is said to "pull" if it completes a lane change in less than 7 seconds (with no steering correction from the driver) when driving at 60

MPH on a road with less than 2 degrees of road crown slope. All four wheels must pass into the other lane during this time (7 seconds).

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-073A Date: 130128

Campaign P1234 - Navigation Software Update For Various Issues

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 522

Reference:

NTB11-073a

Date:

January 28, 2013

VOLUNTARY SERVICE CAMPAIGN CALL WAITING FUNCTION NAVIGATION UPDATE

This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions

of this bulletin.

CAMPAIGN ID #: P1234

APPLIED VEHICLES:

2010-2011 Altima Sedan, Coupe, and Hybrid (L32, CL32, & L32HV)

2010-2011 Maxima (A35)

2010 - 2011 370Z Coupe and Roadster (Z34 and HZ34)

2011 GT-R (R35)

Check Service Comm to confirm campaign eligibility.

INTRODUCTION

On the Applied Vehicles listed above, the navigation, mobile phone, iPod(R), and voice recognition functions may not be working as intended. To

remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or

labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system.

IDENTIFICATION NUMBER

Nissan has assigned identification number P1234 to this campaign. This number must appear on all communications and documentation of any

nature dealing with this campaign.

DEALER RESPONSIBILITY

Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private

parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.

REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE

^ Discs 1/3 and 2/3 of the set shown in Figure A are used for 2010 models in this campaign.

^ Do not use disc 3/3.

^ This NEW disc (Figure B) is required for all applied models in this campaign.

^ This disc replaces disc 3/3 above.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 523

^ This disc also replaces disc NTB10-125b / ITB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.

NOTE:

Numbers on these discs do not match this bulletin's reference number or the campaign ID #.

^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.

^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number

1-800-347-8933. Request a new disc using the information printed on the disc.

CLAIMS INFORMATION

Submit a Campaign (CM) line claim using the claims coding:

Service Procedure

For 2011 Models refer to 2011 Models - Installing the Navigation Update

2010 Models - Installing the Navigation Update

IMPORTANT:

Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function, otherwise the Navigation System may continuously reboot the

next time it is turned on.

NOTE:

This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to

a low charge rate (trickle charge).

For 2010 models there are three sections:

A. Disable Bluetooth(R) Function

B. Loading the Program

C. Check Bluetooth(R) Setting

A: Disable Bluetooth(R) Function

1. Set the parking brake.

2. Turn the ignition ON and keep the transmission in Park or Neutral.

3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

4. Press the "SETTING" button on the switch panel.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 524

5. Touch "Bluetooth".

6. Make sure Bluetooth is OFF.

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is OFF when the ON indicator is "grayed-out".

7. Turn the ignition OFF and wait for 10 seconds.

8. Go to B: Loading the Program.

B: Loading the Program -2010 Models

NOTE:

For 2011 Models, refer to 2011 Models - Installing the Navigation Update.

1. Turn the ignition ON - keep the transmission in Park or Neutral.

^ The navigation start-up screen should display.

NOTE:

If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 525

4. Select "Navigation Version" on the display screen.

5. Check "Map Version".

^ If the Map Version is 09-10 MAP No.1 or 09-10 MAP No.1a

a. Continue with Step 6.

^ If the Map Version is any other then above:

a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD / DVD player.

The other Discs will not be needed.

b. Skip to step 18.

6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

7. Insert disc ITB10-031 / NTB10-068 (Disc 1/3) into the in-dash CD/DVD player.

^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.

IMPORTANT:

Once reprogramming has started:

^ Do not eject a disc while it is loading.

^ Do not change the ignition position until all discs have been loaded.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 526

^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.

8. Wait for the program to load (progress bar will display).

9. When the program has finished loading:

^ Disc will automatically eject, and

^ "Program loading is completed" will display.

10. Carefully remove the disc.

11. The navigation system will automatically restart.

12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).

13. Touch "DVD update".

14. Touch "Yes" to begin the map update process.

^ Map update will take about 15 minutes.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 527

15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.

16. The navigation system will automatically restart.

17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).

18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:

^ If the screen in Figure 13 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Go to C: Check Bluetooth(R) Setting.

^ If "Now preparing loading shown in Figure 14 is displayed, reprogramming will begin automatically.

> Follow the on-screen Caution during the reprogram.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 528

19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure 15)

^ Rewriting program data (Figure 16)

^ Rewriting language data (Figure 17)

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

20. When the first part of the reprogram has finished loading:

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 529

^ "Program loading is completed will be displayed (Figure 18).

^ The Re-programming Software DVD will automatically eject.

21. Remove the DVD and continue to the second part of the update - step 22.

22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 25.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 530

23. "Rewriting boot data" (Figure 20) and "Rewriting program data" (Figure 21) will be displayed.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

24. After the reprogram has completed:

^ "Program loading is completed will be displayed (Figure 22).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 25.

After Navigation has restarted:

25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD

slot again.

One of the following screens will display:

^ If Figure 23 is displayed, it indicates that the reprogram has been completed.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 531

> If complete, go to step 26.

^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 18.

> Follow steps 18 through 25 again.

26. Eject the DVD.

27. Go to C: Check Bluetooth(R) Setting.

C: Check Bluetooth(R) Setting - 2010 Models

1. Press the "Setting button on the switch panel.

2. Touch "Bluetooth".

3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).

^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.

^ Bluetooth is ON when the ON indicator displays in orange.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 532

^ Bluetooth is OFF when the ON indicator is "grayed-out".

4. Turn the ignition OFF. The process is complete.

2011 Models - Installing the Navigation Update

NOTE:

This procedure will take 10 - 15 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set

to a low charge rate (trickle charge).

1. Turn the ignition ON - keep the transmission in Park or Neutral (parking brake ON).

2. Wait for more than 1 minute.

3. Press the "INFO" button on the switch panel.

4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).

^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.

5. Load the new disc "NTB12-070/1TB12-054 Re-programming Software DVD into the CD slot of the audio unit.

One of the following screens will display:

^ If the screen in Figure A1 is displayed, this disc is not needed.

> Remove/eject the DVD from the CD slot.

> Procedure is complete.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 533

^ If "Now preparing loading shown in Figure A2 is displayed, reprogramming will begin automatically.

> Follow the on screen Caution during the reprogram.

6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:

^ Rewriting boot data. (Figure A3)

^ Rewriting program data (Figure A4)

^ Rewriting language data (Figure A5)

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 534

IMPORTANT:

Once the reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

7. When the first part of the program has finished loading:

^ "Program loading is completed will be displayed (Figure A6).

^ The Re-programming Software DVD will automatically eject.

8. Remove the DVD and continue to the second part of the update - step 9.

9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a

second time.

^ If not (Navigation System restarts), go to step 12.

^ If so, re-insert DVD disc.

> At the top of the screen "Program Loading (2nd)" will be displayed.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 535

10. "Rewriting boot data and "Rewriting program data will be displayed once the DVD is reinstalled.

IMPORTANT:

Once reprogramming has started:

^ Do not eject the DVD while it is loading.

^ Do not change the ignition position until the DVD has been loaded.

11. After the reprogram has completed:

^ "Program loading is completed will be display (Figure A10).

^ The Re-programming Software DVD will automatically eject.

^ The Navigation system will restart. Proceed to step 12.

After Navigation has restarted:

12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 back into the CD slot again.

One of the following screens will display:

^ If Figure A11 is displayed, it indicates that the re-program has been completed.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 536

> If complete go to step 13.

^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:

> Go back to step 5.

> Follow steps 5 through 12 again.

13. Eject the DVD.

14. Turn the ignition OFF. Procedure is complete.

2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 537