Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-013 Date: 110215

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-013 Date: 110215



Interior - A-Pillar Trim Removal/Installation Procedure



Classification: BT11-003



Reference: NTB11-013



Date: February 15, 2011



2010 - 2011 ALTIMA; FRONT PILLAR FINISHER REMOVAL



APPLIED VEHICLE: 2010-2011 Altima Sedan (L32)



2010-2011 Altima Hybrid (L32HV)



NOTE:



Does not apply to Altima Coupe



SERVICE INFORMATION



If either one or both front pillar finishers has to be removed for any reason, refer to REPAIR PROCEDURE.



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 232



SERVICE PROCEDURE



Remove Front Pillar Finisher



IMPORTANT



1. Remove the front body side welt (see Figure 1).



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 233



2. Snap loose both clips by carefully prying with a suitable tool where shown in Figure 2.



CAUTION:



The lower clip will not completely snap loose. Attempting to completely snap loose by force may damage the finisher. Continue to Step 3 for proper



removal.



3. Unfasten the lower clip from the front pillar finisher (finisher) with a suitable tool. See Figure 3 and 4.



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 234



4. Tip the top of the finisher inward, and then pull out (see Figure 5).



5. Remove the lower clip from the "A" pillar by pinching and then flipping upward (see Figure 6).



Re-install Front Pillar Finisher



1. Insert the lower clip on the finisher (see Figure 7).



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 235



2. Re-install the finisher by inserting its locator tabs into their slots (see Figure 8 and 9).



3. Align the lower and upper clips into their slots, and then press both into place (see Figure 10).



4. Re-install the front body side welt.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more