Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-048B Date: 111003

2017 Nissan-Datsun Altima Technical Service Bulletin # 10-048B Date: 111003



Keyless Systems/TPMS - SIGNAL TECH II(R) Diag. Tool



Classification: WT10-001B



Reference: NTB10-048B



Date: October 3, 2011



SIGNAL TECH II DIAGNOSTIC TOOL



This bulletin has been amended. The note below APPLIED VEHICLES was amended. Please discard previous versions of this bulletin.



APPLIED VEHICLES: All Nissan with Tire Pressure Monitor System (TPMS), Remote Keyless Entry, or Intelligent Key.



NOTE:



Failure to update Signal Tech II may lead to misdiagnosis of certain models.



^ The latest software is available on the CONSULT III PC at: ASIST> Specialty Tools > Signal Tech II



^ If you should encounter problems updating Signal Tech II, contact Techmate.



^ Future updates will be released as needed. Check ASIST frequently for this information.



SERVICE INFORMATION



If service is required on a vehicle's Tire Pressure Monitor System (TPMS), remote keyless entry, or Intelligent Key, the Signal Tech II (special tool



J-50190) can be used for diagnostics.



Signal Tech II will quickly:



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 207



^ Activate and display TPMS Sensor IDs



^ Display tire pressure reported by the TPMS sensor



^ Read TPMS DTCs and register TPMS IDs



^ Store and print reports for warrantable repairs



^ Check Intelligent Key relative signal strength



^ Test remote keyless entry relative signal strength



^ Confirm vehicle Intelligent Key antenna relative signal strength output



^ Read ENGINE DTCs



Other available information for Signal Tech II:



^ Signal Tech II Quick Start Guide: ASIST> Tools & Equipment > Tool & Equipment Web Page



^ Signal Tech II Users Guide: ASIST > Tools & Equipment> Tools & Equipment Web Page



^ Tool Flyer: ASIST > Tools & Equipment > Tools & Equipment Web Page> Nissan Essential Tool Flyers



^ Tech Talk Article: ASIST > Tech Support Info> TECH TALK / XTRA> Spring 2010 issue

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more