2014 Nissan-Datsun Altima Diagrams. DTC # 08-072A Date: 101007

2014 Nissan-Datsun Altima Diagrams. DTC # 08-072A Date: 101007

Interior - Rough Driver's Power Seat Operation

Classification: EL08-005A

Reference: NTB08-072A

Date: October 7, 2010

2007-2010 ALTIMA; DRIVERS POWER SEAT SLIDE TRAVEL ROUGH

This bulletin has been amended. The Relevant Vehicles and the Parts Information has changed.

RELEVANT VEHICLES:

2007-2010 Altima (L32)

2007-2010 Altima Hybrid (L32HV)

IF YOU CONFIRM

The driver's power seat slide travel front to back is rough.

ACTION

For all 2010 Altimas and 2009 Altimas built from:

^ 1N4(*)L(*)1E(*)9 C 151712/5-Nov-2008

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 460

^ 1N4(*)L(*)1E(*)9 N 453274/4-Nov-2008

Install the Power Track Service Kit to resolve the issue. Refer to the Service Procedure.

NOTE:

Do not replace the seat bottom or seat lower assembly for this issue, if it should occur.

For 2007 through 2009 Altimas built to:

^ 1N4(*)L(*)1E(*)9 C 151711/5-Nov-2008

^ 1N4(*)L(*)1E(*)9 N 453273/4-Nov-2008

This bulletin does not apply. Replace the Seat Lower Assembly using standard Nissan Warranty Practices.

IMPORTANT:

The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service

Procedure as it contains information that is essential to successfully completing this repair.

PARTS INFORMATION

CLAIMS INFORMATION

SERVICE PROCEDURE

IMPORTANT:

Follow all cautions, warnings, and notes in the Electronic Service Manual (ESM) when working on or near a Supplemental Restraint System (SRS),

such as an air bag.

1. Write down the radio station presets.

2. Slide the driver's seat fully rearward and remove the front two seat-to-body bolts.

3. Tilt the seat back to the upright position and remove the headrest.

4. Slide the seat mid-travel, raise the seat all the way up, and remove the rear seat-to-body bolts.

5. Disconnect both 12V battery cables, negative cable first, and wait at least 3 minutes before proceeding to step 6.

6. Disconnect the seat harnesses from the body harnesses.

7. Remove the seat from the vehicle.

8. Place the seat, back side down, on a clean covered workbench.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 461

9. Remove the seat bottom plastic side shields.

10. Disconnect the power harness and clip from the track motor.

11. Remove all eight nuts holding the lower seat track to the seat as shown. The lower rack will not be reused.

12. Remove the new track assembly from the shipping package and lay it next to the seat as shown.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 462

13. Set the seat assembly onto all eight studs of the new lower track assembly.

14. Tighten all eight nuts in sequence as shown.

15. Remove the four bolts and the plastic bracket. The plastic bracket will not be reused.

2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 463

16. Connect the track motor power harness and clip.

17. Reinstall the plastic shields.

18. Reinstall the seat into the vehicle, reconnecting the seat harnesses to the body harnesses while doing so.

IMPORTANT:

Be sure that all Side Air Bag harnesses are routed correctly and that all connectors are firmly seated.

19. Install the four seat-to-body bolts in the sequence shown in Figure 7

TORQUE: 40 Nm (3.9 kg-m, 35 ft-lb).

20. Reinstall the headrest.

21. Reconnect the battery cables.

22. Check seat for proper operation.

23. Reprogram the radio presets.

24. Reinitialize power windows and other systems as needed.