Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 09-131A Date: 110815

2014 Nissan-Datsun Altima Diagrams. DTC # 09-131A Date: 110815



Vehicle - Certification Label/VIN Plate Replacement



Classification: BT09-020A



Reference: NTB09-131A



Date: August 15, 2011



CERTIFICATION LABEL AND VIN PLATE REPLACEMENT



This bulletin has been amended. Please discard previous versions of this bulletin.



APPLIED VEHICLES: All Nissan



SERVICE INFORMATION



Because of collision damage or other vehicle repair, a replacement "Certification Label or "VIN Plate/Label" may be needed.



NOTE:



Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label.



These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for



such replacements.



^ The "VIN Plate/Label" (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see



Figure 1).



^ The "Certification Label" (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).



CERTIFICATION LABEL REPLACEMENT CRITERIA



NOTE:



See "Replacement VIN plate/label" below.



A replacement Certification Label may be requested ONLY if the vehicle is in a collision and:



^ The Certification Label is damaged, or



^ The Certification Label is attached to a part that will be replaced during the repair.



REQUESTING A REPLACEMENT CERTIFICATION LABEL



1. Take a photo of the original Certification Label in its original location on the vehicle B pillar.



^ A photo of the original Certification Label before it is removed must accompany the application; or processing will be significantly delayed or



rejected.



^ If the vehicle is produced outside of the U.S. and a legible Certification Label photo is not provided, the request will be rejected.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 246



^ If the vehicle is produced in the U.S. and is greater than 60 days old and a legible Certification Label photo is not provided, the request will be



rejected.



2. Completely fill out a copy of the APPLICATION FOR REPLACEMENT CERTIFICATION LABEL shown above.



3. Remove the original Certification Label from the vehicle and attach in the designated area on the application form.



^ Processing will be significantly delayed or rejected if the original Certification Label is not available (or a legible photo).



4. Staple the photo of the original Certification Label (in its original location) to the application form.



5. Mail (DO NOT FAX) the completed application with the photo of the label to your Regional Office: Attention: Replacement Certification and



VIN Plate Request.



NOTE:



Your dealer "Non Vehicle Account" will be billed $25.00 for each replacement label.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 247



NOTE



VIN PLATE/LABEL REPLACEMENT CRITERIA



APPLICATION FOR REPLACEMENT VIN PLATE/LABEL



NOTE



Refer to "Replacement Certification Label"



A replacement VIN plate/Label may be requested ONLY if:



^ The vehicle is in a collision and the VIN plate/label is damaged.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 248



or



^ The vehicle was recovered after being stolen and the VIN plate/label is damaged but still available.



REQUESTING A REPLACEMENT VIN PLATE / LABEL



1. Completely fill out a copy of the APPLICATION FOR REPLACEMENT VIN PLATE / LABEL.



2. Remove the original VIN plate/label from the vehicle and attach in the designated area on the application form.



^ The original VIN plate/label MUST accompany the application.



^ For a VIN label that will destroy itself when removed:



> A photo of original instrument panel VIN Label must accompany the application



> A photo of the Certification label (on the B-pillar) clearly showing the VIN must also accompany the application.



^ Stolen VIN plate/label:



> If a VIN Plate/Label is stolen, contact the appropriate State Police or State Department of Motor Vehicles (DMV). In most cases, the State



DMV will issue a unique VIN so the original VIN can be included on stolen vehicle listings. If this is the case, a replacement VIN



plate/label is NOT available from Nissan. However, the original VIN, not the state issued VIN, must be used on all warranty claims.



3. Mail (DO NOT FAX) the completed application with the photo of the label to your Regional Office: Attention: Replacement Certification and



VIN Plate Request.



NOTE:



^ Your dealer "Non Vehicle Account" will be billed $25.00 for each replacement VIN plate/label.



^ All replacement VIN plates/labels are subject to approval by the Technical Compliance Department. If you have any specific questions,



contact your Owner Relations Manager (ORM).

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...