Skip to main content

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-153 Date: 101223

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-153 Date: 101223



Brakes - Feel More Sensitive Than Expected



Classification: BR10-013



Reference: NTB10-153



Date: December 23, 2010



2010-2011 ALTIMA AND MAXIMA;



BRAKES FEEL MORE SENSITIVE THAN EXPECTED



APPLIED VEHICLES:2010-2011 Altima Sedan & Coupe (L32 & CL32)



2010-2011 Maxima (A35)



APPLIED VINs: 2010 Altima built after:



1N4(*)L2(***)AC 173905 (Smyrna) or 1N4(*)L2(***)AN 527905 (Canton)



2011 Altima built before:



1N4(*)L2(***)BC 105774 (Smyrna) or 1N4(*)L2(***)BN 407818 (Canton)



2010 Maxima built after: 1N4AA5AP(*)AC 862521



2011 Maxima built before: 1N4AA5AP(*)BC 807780



APPLIED DATE Vehicles built between June 9, 2010 and September 21, 2010



IF YOU CONFIRM



The brakes feel more sensitive than expected with light to moderate brake application,



and/or



Towards the end of bringing the vehicle to a stop (last few feet), the vehicle stops SLIGHTLY quicker than expected.



ACTION



Replace the Brake Booster Assembly



^ Refer to section BR in the appropriate Service Manual for brake booster replacement information.



^ Use the new brake booster listed in the Parts Information.



PARTS INFORMATION



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 223

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more