Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-140 Date: 091208

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-140 Date: 091208



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 392



A/T - CVT Oil Leak Diagnosis Information



Classification: AT09-012



Reference: NTB09-140



Date: December 8, 2009



CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE



APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)



SERVICE INFORMATION



If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.



1. Thoroughly clean off the area of the suspected leak.



2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.



3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).



4. Inspect with lamp from J-43926 A/C Dye Kit*



If no fluorescent oil trace/leak is found, the stain is probably:



^ corrosion protection chemicals sprayed on the transmission



and/or



^ lubricants which are sometimes used to ease the assembly process.



NOTE:



These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.



If a fluorescent oil trace/leak is found:



^ Repair using standard warranty procedures.



*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.



NOTE:



The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more