Skip to main content

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-009 Date: 110209

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-009 Date: 110209



Interior - Front Seat Side Finisher Removal Procedure



Classification: BT11-002



Reference: NTB11-009



Date: February 9, 2011



2007 -2011 ALTIMA SEDAN;



FRONT SEAT SIDE FINISHER REMOVAL



APPLIED VEHICLES:



2007-2011 Altima Sedan (L32)



2007-2011 Altima Hybrid (L32HV)



IF YOU CONFIRM



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 326



^ A front seat outboard side finisher needs to be removed for any reason.



ACTION



Follow the Service Procedure in this bulletin for removal.



IMPORTANT:



The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service



Procedure as it contains information that is essential to successfully completing this repair.



SERVICE PROCEDURE



1. Remove adjustment knobs or lever (see Figures 2 and 3).



^ For manual seat - remove the adjustment lever



^ For power seats - remove the adjustment knobs.



If needed, use a plastic trim tool.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 327



2. Remove the screw at the rear of the finisher.



3. Insert a clean medium size flat blade screw driver between the seat cushion and the finisher as shown in Figure 5.



4. Release metal clip by pushing on the finger (see Figure 6).



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 328



5. Unsnap/unclip the rest of the finisher as shown in Figure 7.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more