Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-042 Date: 110420

2017 Nissan-Datsun Altima Technical Service Bulletin # 11-042 Date: 110420



CVT - Output Speed Sensor Service



Classification: AT11-007



Reference: NTB11-042



Date: April 20, 2011



2007-2011 ALTIMA, JUKE, ROGUE, SENTRA; CVT OUTPUT SPEED SENSOR SERVICE



APPLIED VEHICLES:



2007-2011 Altima (C/L32) QR25 ONLY



2011 Juke (F15)



2008-2011 Rogue (S35)



2007-2011 Sentra (B16) MR20 & QR25 ONLY



SERVICE INFORMATION



If the Output Speed Sensor has been removed and replaced for any reason:



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 316



NOTE:



Input/Turbine Speed Sensor does not require shims. That Sensor is flush mounted to CVT casting.



The correct number of spacer shims must be installed between the Sensor and the CVT body.



Refer above for shim number application chart.



SERVICE PROCEDURE



1. Determine required number of shims by model:



2. Assemble the Output Speed Sensor with the proper 0-ring.



3. Place bolt with attached washers through hole on the Sensor.



4. After determining the correct number of washers for the vehicle, place the shims over the portion of the bolt that is exposed below the sensor



body.



5. Assemble as seen below: Torque retaining bolt to 5.9 Nm (0.6 kg-m, 52 in-lb)



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 317

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more