Tuesday, June 18, 2019
Monday, June 17, 2019
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-153 Date: 101223
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-153 Date: 101223
Brakes - Feel More Sensitive Than Expected
Classification: BR10-013
Reference: NTB10-153
Date: December 23, 2010
2010-2011 ALTIMA AND MAXIMA;
BRAKES FEEL MORE SENSITIVE THAN EXPECTED
APPLIED VEHICLES:2010-2011 Altima Sedan & Coupe (L32 & CL32)
2010-2011 Maxima (A35)
APPLIED VINs: 2010 Altima built after:
1N4(*)L2(***)AC 173905 (Smyrna) or 1N4(*)L2(***)AN 527905 (Canton)
2011 Altima built before:
1N4(*)L2(***)BC 105774 (Smyrna) or 1N4(*)L2(***)BN 407818 (Canton)
2010 Maxima built after: 1N4AA5AP(*)AC 862521
2011 Maxima built before: 1N4AA5AP(*)BC 807780
APPLIED DATE Vehicles built between June 9, 2010 and September 21, 2010
IF YOU CONFIRM
The brakes feel more sensitive than expected with light to moderate brake application,
and/or
Towards the end of bringing the vehicle to a stop (last few feet), the vehicle stops SLIGHTLY quicker than expected.
ACTION
Replace the Brake Booster Assembly
^ Refer to section BR in the appropriate Service Manual for brake booster replacement information.
^ Use the new brake booster listed in the Parts Information.
PARTS INFORMATION
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 223
Sunday, June 16, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-079 Date: 100621
Electrical - MIL ON/DTC P0128 Due To Remote Start Sys.
Classification: EC10-017
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 252
Reference: NTB10-079
Date: June 21, 2010
MIL "ON" WITH DTC P0128 (THERMOSTAT FUNCTION) STORED
APPLIED VEHICLES: 2002 and later Nissan vehicles
IF YOU CONFIRM
The MIL is "ON" with P0128 (Thermostat Function) stored.
ACTIONS
1. Check to see if an aftermarket remote starter system is installed.
^ Remote starter systems may cause the MIL to illuminate and DTC P0128 to store.
2. If a remote starter system is installed, remove/disconnect it before performing diagnostic procedures on the vehicle.
3. Refer to ASIST and the Electronic Service Manual (ESM) for diagnostic information.
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
2014 Nissan-Datsun Altima Diagrams. DTC # 11-015B Date: 130201
Engine - Oil Leakage From The Upper End Of Oil Cooler
Classification:
EM10-002b
Reference:
NTB11-015b
Date:
February 1, 2013
ALTIMA SEDAN AND COUPE, SENTRA, AND ROGUE WITH QR25DE ENGINE; OIL LEAK
This bulletin has been amended in APPLIED VEHICLES, SERVICE PROCEDURE, PARTS INFORMATION, and CLAIMS INFORMATION.
Discard all previous versions of this bulletin.
APPLIED VEHICLES:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 488
2007 - 2012 Altima Sedan (L32)
2008 - 2013 Altima Coupe (CL32)
2007-2012 Sentra (B16)
2008 - 2013 Rogue (535)
APPLIED ENGINE:
QR25DE (4 cyl)
IF YOU CONFIRM:
Oil is leaking from the upper end of the engine oil cooler (oil cooler). See Figure 1.
ACTION:
Reseal the oil cooler with the parts listed in the PARTS INFORMATION.
^ For repairs refer to SERVICE PROCEDURE.
NOTE:
Do not replace the complete engine oil cooler assembly for this incident if it should occur.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 489
CLAIMS INFORMATION
SERVICE PROCEDURE
1. Remove the oil cooler from the engine block.
^ Refer to the appropriate section of the Electronic Service Manual (ESM) if needed.
^ Perform repairs in a clean work environment.
2. Remove the four (4) bolts, and then remove the upper half of the oil cooler. See Figure 2.
3. Remove the O-ring gasket, and then thoroughly clean out the gasket area and around it with a suitable cleaner.
^ The dashed line in Figure 3 shows the O-ring gasket area to be cleaned.
^ Make sure no debris or contaminants get into the holes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 490
^ Also clean underneath the upper half of the oil cooler (no picture shown).
4. Lightly coat the new O-ring gasket (see PARTS INFORMATION) with engine oil, and then put it in place. See Figure 4.
5. Install the upper half of the oil cooler with the bolts.
6. Torque the bolts in two steps: first step at half value, and then the second step at full value (listed below).
^ Bolts torque sequence:
1-2-3-4-5-6-7-8 (see Figure 5).
^ Bolts torque:
4.0 N.m (0.41 kg-m, 35.4 in lb)
7. Install the oil cooler to the engine with a new gasket (see PARTS INFORMATION).
Refer to the appropriate section of the ESM if needed.
Saturday, June 15, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-080 Date: 110824
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-080 Date: 110824
Steering/Suspension - Rear Axle Bolt/Torque Change
Classification: RA11-002
Reference: NTB11-080
Date: AUGUST 24, 2011
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 236
ALTIMA AND MAXIMA;
AXLE BOLT AND TORQUE CHANGE
APPLIED VEHICLES:
2002-2012 Altima Coupe, Sedan, and Hybrid (L31, C/L32/HV)
2004-2012 Maxima (A34, A35)
SERVICE INFORMATION
If bolt 56280-JA000 needs to be replaced in the following location:
^ Rear Shock Absorber to Rear Knuckle (see Figure 1 above)
...AND the vehicle is 2002-2012 Altima or 2004-2012 Maxima,
1. Order bolt 56280-JA00A instead of 56280-JA000.
2. Torque bolt 56280-JA00A to 80-100 Nm (8.2-10.2 kg-m, 59-74 ft-lb).
If bolt 56280-JA000 needs to be replaced in the following location:
^ Front Lower Link to Rear Knuckle (see Figure 1)
...AND the vehicle is 2007-2012 Altima or 2009-2012 Maxima,
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 237
1. Order bolt 56280-JA00A instead of 56280-JA000.
2. Torque bolt 56280-JA00A to 83-103 Nm (8.5-10-5 kg-m, 61-76 ft-lb).
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-074 Date: 120912
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-074 Date: 120912
Computers/Controls - CONSULT III Plus(R) Saved Data List
Classification: EC12-021
Reference: NTB12-074
Date: September 12, 2012
SAVED DATA LIST REPROGRAMMING WITH CONSULT III PLUS
SERVICE INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 84
^ When performing a "Reprogramming" operation with C-III plus, the screen in Figure 1 may display.
^ This screen displays "Saved Data" from previous C-III plus operations.
^ During the initial "Reprogramming Confirmation" set-up, if you get this screen:
1. Select Delete, then
2. Select Other Operation, then
3. Continue with the reprogramming procedure.
NOTE:
If reprogramming does not complete, this screen can display for reprogramming recovery. Do not select Delete if this screen displays
during reprogram recovery.
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
2014 Nissan-Datsun Altima Diagrams. DTC # 11-073A Date: 130128
Campaign P1234 - Navigation Software Update For Various Issues
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 522
Reference:
NTB11-073a
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN CALL WAITING FUNCTION NAVIGATION UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
CAMPAIGN ID #: P1234
APPLIED VEHICLES:
2010-2011 Altima Sedan, Coupe, and Hybrid (L32, CL32, & L32HV)
2010-2011 Maxima (A35)
2010 - 2011 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, iPod(R), and voice recognition functions may not be working as intended. To
remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or
labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system.
IDENTIFICATION NUMBER
Nissan has assigned identification number P1234 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for 2010 models in this campaign.
^ Do not use disc 3/3.
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 523
^ This disc also replaces disc NTB10-125b / ITB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-800-347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
For 2011 Models refer to 2011 Models - Installing the Navigation Update
2010 Models - Installing the Navigation Update
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function, otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
For 2010 models there are three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program
C. Check Bluetooth(R) Setting
A: Disable Bluetooth(R) Function
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 524
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program -2010 Models
NOTE:
For 2011 Models, refer to 2011 Models - Installing the Navigation Update.
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 525
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No.1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD / DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB10-068 (Disc 1/3) into the in-dash CD/DVD player.
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 526
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 527
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
^ If "Now preparing loading shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 528
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the reprogram has finished loading:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 529
^ "Program loading is completed will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update - step 22.
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 530
23. "Rewriting boot data" (Figure 20) and "Rewriting program data" (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 531
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting - 2010 Models
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 532
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
2011 Models - Installing the Navigation Update
NOTE:
This procedure will take 10 - 15 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set
to a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral (parking brake ON).
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
5. Load the new disc "NTB12-070/1TB12-054 Re-programming Software DVD into the CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 533
^ If "Now preparing loading shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on screen Caution during the reprogram.
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 534
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the program has finished loading:
^ "Program loading is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update - step 9.
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 535
10. "Rewriting boot data and "Rewriting program data will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 back into the CD slot again.
One of the following screens will display:
^ If Figure A11 is displayed, it indicates that the re-program has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 536
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 5 through 12 again.
13. Eject the DVD.
14. Turn the ignition OFF. Procedure is complete.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 537
Friday, June 14, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-017 Date: 100201
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-017 Date: 100201
Instruments - Fuel Gauge Issues/DTC's P0461/P0462/P0463
Classification:
EL09-030
Reference:
NTB10-017
Date:
February 1, 2010
ALTIMA AND MAXIMA; FUEL GAUGE ISSUES
AND/OR DTC P04611 P0462 / P0463
APPLIED VEHICLES:
2007-2010 Altima (L32)
2008-2010 Altima Coupe (CL32)
2008-2010 Altima Hybrid (L32HV)
2009-2010 Maxima (A35)
IF YOU CONFIRM:
The fuel gauge is erratic, inaccurate, or inoperative
And / Or
The MIL is "ON with DIG P0461, P0462, or P0463 stored in Self-Diagnosis.
ACTION:
Replace the fuel level sensor unit.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 394
^ Refer to the SERVICE PROCEDURE section of this bulletin for repair procedure.
^ Use the parts listed in the PARTS INFORMATION section in this bulletin.
NOTE:
Do not replace the entire fuel pump module assembly for this incident, if it should occur.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE
PROCEDURE as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Failed Part (PP) line claim using the claims coding shown.
NOTE:
Version 1 fuel pump module assembly fits on earlier model year Altima models. Version 2 fits on later Altima and all Maxima models.
SERVICE PROCEDURE
1. Remove the fuel pump module assembly (module).
^ Refer to the appropriate section of the Electronic Service Manual (ESM), if needed.
NOTE:
Perform repairs in a clean work environment.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 395
2. Determine which version module you are working on (see Version 1 and 2).
3. Remove the 3 wire terminals with red, white, and double-wire black wires from under the top of the module as shown in Figure 1.
NOTE:
The white wire may appear yellowish in color.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 396
^ Press the tab in and gently pull the wire off its terminal (see Figure 2)
4. Remove the plastic tie strap that holds the wires to the fuel supply hose (supply hose) as shown in Figure 3.
CAUTION:
Be careful not to damage the supply hose or wiring when removing the tie strap.
5. Remove the fuel tank temperature sensor (temp sensor) from its retention feature (see Figure 4).
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 397
6. Version 1: Remove the temp sensor wires from the retention feature (see Figure 5).
7. Version 2 only: Remove the temp sensor wires from both retention features (see Figure 6).
8. Version 1 only: Remove all wires from the retention feature on the module (see Figure 7).
NOTE:
This retention feature is not reused.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 398
9. Version 1 only: Remove the black plastic retainer (retainer) as shown in Figure 8.
^ Pry on the clip ends using a pocket screwdriver or suitable tool, one side at a time (see Figure 8).
10. Remove the level sensor from the module (see Figure 9).
Push the tab inward, and then push the level sensor up, and then pull it away from the module.
11. Install the new level sensor onto the module (no picture shown).
Perform Step 10 in reverse, making sure its tab locks into place.
12. Version 1 only: Reinstall the retainer by snapping it into place (see Figure 10).
^ Make sure the level sensor's wires are not pinched under the retainer.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 399
13. Install the temp sensor into its retention feature (see Figure 11).
14. Version 1 only: Install the temp sensors wiring into the retention feature as shown in Figure 12.
^ Route the temp sensor's wires to the right of the level sensor.
^ Make sure the wiring is clear of float arm movement.
^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.
15. Version 2 only: Secure the level sensors wires into the retention features (see Figure 13).
^ Make sure the wiring is within 0.5 inches (13 mm) from the side of the module.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 400
16. Route the wires on the inside of the supply hose (see Figure 14).
17. Secure the wires to the supply hose with a tie strap as shown in Figure 14.
CAUTION:
Be careful not to damage the supply hose or wires when installing the tie strap.
^ Step 17 applies to both module versions.
NOTE:
Tie straps are considered a shop supply.
18. Install the wires to the correct terminals (see Figure 15 below).
^ Make sure the wires are routed correctly as shown in Figure 15.
--> Red and white wires are routed in front of the blue wire.
--> The double black wire is in between the blue and single black wires.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 401
^ Make sure the tabs are securely locked.
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 04-049H Date: 110413
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 04-049H Date: 110413
Electrical - Trailer Light Wiring Info.
Classification: EL03-043H
Reference: NTB04-049H
Date: April 13, 2011
TRAILER LIGHT WIRING
This bulletin has been amended. The Applied Vehicles have been updated. Please discard previous versions of this is bulletin.
APPLIED VEHICLES
SERVICE INFORMATION
NOTE:
This bulletin provides information to be shared with all affected customers.
^ This TSB contains the appropriate hookup points for connecting a trailer light wiring harness to the towing vehicle's electrical system.
^ The wiring diagrams contained in this bulletin are for Nissan vehicles that have trailer towing capability (see the owners manual) but do not have a
Genuine Nissan accessory towing kit (with wiring) available.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 318
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 319
^ When splicing into the vehicle electrical system, a power-type module/converter must be used to provide power for all trailer lighting. A
power-type module/converter uses the vehicle battery as a direct power source for all trailer lights while using the vehicle taillight, stoplight, and
turn signal circuits only as a signal source. (See the illustration above.) The module/converter must draw no more than 5 milliamps from the
vehicle turn signal circuits and no more than 15 milliamps from the stop and tail light circuits.
CAUTION:
Using a module/converter that exceeds these power requirements listed above may negatively affect the performance and function of the vehicle's
electrical system.
See a professional trailer dealer or trailer rental agency for installation of the proper equipment.
Customers who inquire about towing should be reminded of the following:
^ Always check for correct operation of the turn signals, stoplights, and taillights every time a trailer is hitched up for towing.
^ The towing capacity for 350Z (Coupe Only), Altima, Maxima, and Sentra is 1,000 lbs.
For more information, refer customers to the Owner's Manual as well as the Nissan Towing Guide, available online at NissanUSA.com.
Thursday, June 13, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426
Interior - Door Panel Looks Faded/Discolored
Classification: BT08-031B
Reference: NTB08-090B
Date: April 26, 2011
ALTIMA AND MAXIMA; DOOR PANEL LOOKS DISCOLORED / FADED
This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard all previous versions.
APPLIED VEHICLES:
2007-2011 Altima Coupe, Sedan, and Hybrid (C/L32/HV)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 312
2009-0211 Maxima (A35)
SERVICE INFORMATION
If a door panel looks discolored or faded as shown in Figure 1:
^ The probable cause is dirt buildup in the grain of the material. See below for details on how to clean the door panel.
NOTE:
^ Vehicle care and maintenance (cleaning) is not covered under warranty.
^ DO NOT replace the door panel when cleaning will solve the incident.
A soiled door panel can be cleaned as follows:
^ Following the instructions on the label, apply Nissan Vinyl and Leather Cleaner to the door panel surface.
^ Gently use a soft bristle brush to remove trapped dirt.
^ Spray the area with water.
^ Wipe the area clean using a clean cloth.
^ Repeat the cleaning procedure as needed.
After treating the soiled area, the door panel should be clean as shown in Figure 2.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 313
Wednesday, June 12, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
2014 Nissan-Datsun Altima Diagrams. DTC # 11-074A Date: 110818
Computers/Controls - CONSULT(R) Reprogramming Info.
Classification: EC11-021A
Reference: NTB11-074A
Date: August 18, 2011
REPROGRAMMING WITH CONSULT
This bulletin has been amended. The statements below have changed. No other changes have been made. Please discard any previous copies.
APPLIED VEHICLES: All Nissan vehicles with a reprogrammable ECU
SERVICE INFORMATION
If you have a reprogram that requires the use of CONSULT-IT (C-II, and C-II is not available:
^ Refer to the chart below to determine CONSULT applicability.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 477
CURRENT REPROGRAMMING APPLICABILITY CHART
Reprogramming C-II Loaner Program
(Available ONLY for reprogramming use)
^ Contact TECH LINE and they will determine if a C-II Loaner is needed. If so they will make arrangements for the loaner to be shipped.
^ Dealerships must return the C-II Loaner immediately after the reprogramming is completed.
^ If the Loaner is not returned within one week of delivery, your FOM will be contacted to collect the unit.
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-141 Date: 091208
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-141 Date: 091208
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 355
Engine - Reman Engine Start Up Lubrication Information
Classification: EM09-010
Reference: NTB09-141
Date: December 8, 2009
REMANUFACTURED ENGINE LUBRICATION UPON INITIAL START UP
APPLIED VEHICLE: All Nissan vehicles having a remanufactured engine installed
SERVICE INFORMATION
During remanufactured engine storage, upper engine lubrication may dissipate/disperse. Camshaft scoring or seizure may occur at initial start up
unless the procedure below is followed.
1. Refer to the MA section of the applicable Electronic Service Manual (ESM) to determine the specified volume of oil required to fill both the
crankcase and filter.
2. Set one (1) quart of oil aside and fill the crankcase with the remaining quantity (one quart should remain unused).
3. Prior to initial engine start up, pour the one (1) remaining quart of oil into the valve cover.
^ It is recommended to quickly squeeze the quart of oil out of the container to "flood" the camshafts and cam bearings.
4. Immediately start the engine while the upper end is "flooded" with oil.
Tuesday, June 11, 2019
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
2014 Nissan-Datsun Altima Diagrams. DTC # 98-018F Date: 121107
Emissions - System Readiness Test (SRT) Drive Patterns
Classification: EC98-001F
Reference: NTB98-018F
Date: November 7, 2012
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
This bulletin has been amended. Several Changes were made at "Step 7: Confirm All SRTs "COMPLETE"". Please discard all previous versions of
this bulletin.
APPLIED VEHICLES: 1996 and newer Model Years as required by State Emissions Inspections Regulations.
SERVICE INFORMATION
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be
checked.
^ The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components.
^ In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed.
The State Emissions Inspection Station may advise a Nissan customer to return to the dealership for service due to one or more SRT items coming
up "INCOMPLETE." Use the information in this Bulletin to help you "COMPLETE" the SRT.
^ In most cases the ECM will automatically complete its self diagnosis cycle during normal vehicle usage, and the SRT status will indicate
"COMPLETE" for each applicable system.
^ Once indicating "COMPLETE", the SRT status remains "COMPLETE" until the Self Diagnosis memory is erased.
^ Occasionally, certain portions of the self diagnostic test may not be completed as a result of the customer's normal driving pattern. In these cases
the SRT will indicate "INCOMPLETE" for these items.
NOTE: The SRT will also indicate "INCOMPLETE" if:
^ The self diagnosis memory is erased for any reason, or The ECM memory power supply is interrupted for several hours.
This bulletin contains information to help you perform a comprehensive road test (Drive Pattern) that enables the ECM to complete the SRT.
^ A separate Drive Pattern sheet for each 1996 and 1997 vehicle variation is included with this Bulletin.
^ For 1998 and newer vehicles, refer to the EC section of the appropriate Service Manual for the required Drive Pattern. They are listed under On
Board Diagnostic> System Readiness Test.
NOTE:
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced (i.e. model, model year, engine,
emissions certification, transmission, powertrain, and for 1996/1997 models, ECM part number.
NOTE:
To ensure all ECM Self Test requirements are met, it is important to drive the entire Drive Pattern even if only one SRT item indicates
"INCOMPLETE."
CLAIMS INFORMATION:
Refer to the current Warranty Flat Rate Manual for claims information.
Service Procedure
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 2
SRT WORKFLOW
Step 1: Check for DTC
1. Use a CONSULT tool to check for any stored DTCs.
^ If any DTCs are stored they must be repaired at this time.
^ Refer to ASIST for diagnostic and repair information.
NOTE:
Normal warranty coverage will apply for DTC repairs.
2. If no DTCs are stored, go to the next step.
NOTE:
DO NOT touch "Erase" or you will lose previously completed SRTs.
Step 2: Check SRT Status
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 3
Check the SRT Status (Complete or Incomplete).
^ Use the appropriate CONSULT tool.
^ For older vehicles, a Generic Scan Tool may be needed to check SRT status.
NOTE:
In some cases, the normal driving that occurs between the time the vehicle was referred by the State Emissions Inspection Station and it is
brought into the dealership for SRT evaluation may allow the ECM to complete the SRTs. If this occurs, no further action is necessary.
Always check SRT status before performing the SRT Drive Pattern.
Step 3: Identify the Vehicle
You must select the Drive Pattern that correctly corresponds with all variables for the vehicle being serviced refer to the information below in
the image:
Step 4: Obtain ECM Part Number (1996 and 1997 models only)
1. Use a CONSULT tool to obtain the ECM part number.
2. Write the ECM part number in the space provided above.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 4
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 5
3. Compare the vehicles ECM part number with the list of ECM part numbers provided in the Nissan SRT System Chart above to determine the
Drive Pattern for the vehicle being inspected.
NOTE:
For 1996 and 1997 models; if the vehicles ECM part number does not match a part number listed on the SRT System Chart for that
vehicle, either 1) the vehicle was identified incorrectly or 2) the vehicle has the wrong ECM installed. The SRT cannot be completed with
the incorrect ECM.
Step 5: SRT Road Test (perform Drive Pattern)
To properly obtain SRT readings of "COMPLETE" it is necessary to drive the vehicle under the exact conditions required by the vehicle's
ECM.
Be sure to select the correct Drive Pattern. The SRTs will not complete if the wrong drive pattern for that vehicle is used.
1. Select the Drive Pattern based on the Vehicle Identification (see Step 3).
^ For 1996 and 1997 vehicles:
> This bulletin contains a specific Driving Pattern for every 1996 and 1997 Nissan vehicle.
> Use the "Bookmark" on the left side of the ASIST screen to choose the correct model and year.
> Verify that the vehicle ECM P/N matches EXACTLY an ECM P/N listed on the Drive Pattern sheet you chose.
> Print the Drive Pattern to take with you.
^ For 1998 and newer vehicles, refer to the EC section in the appropriate Service Manual for the required Drive Pattern. It is listed under
On-Board Diagnostics> System Readiness Test.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 6
> Print the Drive Pattern to take with you.
2. Prior to driving the vehicle, review the Drive Pattern and prepare to complete it from start to finish:
^ Review the Pre-Check items listed on the drive pattern and ensure all conditions are met.
^ Determine the vehicle speeds required by the drive pattern.
^ Plan your route to minimize traffic and traffic signals that might interrupt the Drive Pattern tasks.
^ Review the Drive Pattern section(s) that must be restarted if you are interrupted.
^ Do not use the ASCD (cruise control) during any section of the Drive Pattern that contains the "No ASCD" symbol.
^ Some EVAP-equipped vehicles will require that fuel be added to the tank between the first and second trip. Be prepared to purchase fuel
or plan your route to accommodate this step.
^ For these EVAP-equipped vehicles, begin the road test with less than 1/2 tank of fuel. If the fuel level is greater than 1/2, more time may
be required to complete the EVAP sections of the Drive Pattern and you may not be able to add fuel as required.
3. Review the Drive Pattern for any input signals that need to be monitored during the drive.
If needed, Connect a CONSULT tool to the vehicle to monitor required signals.
NOTE:
^ Monitor the Fuel Temperature if the EVAP SRT is "INCOMPLETE". One part of the EVAP SRT diagnostic logic requires a 3锟斤拷C
increase in fuel temperature from the time the ignition key is turned to "ON" as part of the test criteria. Fluctuations in the fuel
temperature reading can extend the time required for the EVAP SRT to indicate "COMPLETE". If the fuel temperature change is not
sufficient after completing the SRT Drive pattern, idle the vehicle until a fuel temperature increase of at least 3锟斤拷C is noted or until the
EVAP SRT indicates "COMPLETE".
^ If the fuel temperature increases 3锟斤拷C or more but the SRT still indicates "INCOMPLETE", the SRT Drive Pattern may need to be
repeated.
4. Note the following items before starting the Drive Pattern:
^ IMPORTANT:
Nissan requires using a driver and an assistant to conduct SRT driving patterns. The assistant should read the Drive Pattern, CONSULT
data, and drive time and convey driving instruction to the driver. It is the driver's responsibility to observe and react to traffic conditions.
Always drive the vehicle in a safe manner and obey all traffic laws.
^ To ensure all ECM Self Test requirements are met, drive the ENTIRE pattern whenever any SRT items indicate "INCOMPLETE".
^ Some vehicles require that sections of the Drive Pattern be driven two times to satisfy the "self diagnosis two trip logic". For vehicles
that require two trips, the pre-check engine coolant temperature must be met before beginning Section 1 of the second trip.
5. Perform the Drive Pattern:
a. Make sure all Pre-Check conditions are met.
b. Drive the vehicle and carefully follow the specific instructions and time requirements listed in each section of the Drive Pattern.
NOTE: If you monitor the (B/FUEL SCHDL):
^ The Base Fuel Schedule (B/FUEL SCHDL) is an indication of engine load.
^ It will be easier to match high B/FUEL SCHDL values when driving up slight hills in the recommended gear range.
^ It will be easier to match low B/FUEL SCHDL values when driving down slight hills in the recommended gear range.
^ Turning the A/C compressor ON will increase the B/FUEL SCHDL value, while turning it OFF will decrease the B/FUEL SCHDL
value.
Step 6: Recheck for DTC
Upon completion of the Drive Pattern, determine if any DTCs have been stored. Only in rare cases will this occur.
^ If a DTC has been stored after completing the Drive Pattern, it must be repaired. Refer to ASIST for diagnostic and repair information.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 7
NOTE:
Normal warranty coverage will apply for DTC repairs.
^ Once the DTC is repaired, erase the stored DTC. Turn the ignition OFF for 10 seconds, and then repeat the entire Drive Pattern (Step
5) to "COMPLETE" the SRTs.
^ If no DTCs have been stored, DO NOT touch "Erase" or all SRT items will reset to "INCOMPLETE".
Step 7: Confirm All SRTs "COMPLETE"
If all SRT items indicate "COMPLETE", the inspection is complete.
^ If Catalyst and/or 02 Sensor Monitors show "INCOMPLETE" perform step A or B below.
A. Check Self Learning Value and A/F ALPHA. If either value is +10% or more above target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0171 or P0174 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
A. Check Self Learning Value and A/F ALPHA. If either value is -10% or more below target of 100%, clear Self Learning Value.
^ Perform DTC diagnosis for P0172 or P0175 and check for the following possible causes:
> Intake air leaks
> Front heated oxygen sensors
> Injectors
> Exhaust gas leaks
> Incorrect fuel pressure
> Lack of fuel
> Mass air flow sensor
^ After repairs have been made, run the prescribed drive pattern and check that A/F ALPHA is within +/- 10% of the target of 100%
during the steady state portions of the drive cycle. If it is not, then continue repairs. If it is, return to STEP 5.
System Readiness Test Drive Patterns
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 8
SRT DRIVE PATTERN LAYOUT
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 9
Pattern # 1 - 96 Altima (FED) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 10
Pattern # 2 - 96 Altima (FED) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 11
Pattern # 3 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 12
Pattern # 4 - 96 Altima (CAL) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 13
Pattern # 5 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 14
Pattern # 6 - 96 Altima (CAL) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 15
Pattern # 7 - 97 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 16
Pattern # 8 - 97 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 17
Pattern # 9 - 97.5 Altima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 18
Pattern # 10 - 97.5 Altima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 19
Pattern # 11 - 96 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 20
Pattern # 12 - 96 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 21
Pattern # 13 - 97 Maxima M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 22
Pattern # 14 - 97 Maxima A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 23
Pattern # 15 - 96 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 24
Pattern # 16 - 96 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 25
Pattern # 17 - 97 Pathfinder M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 26
Pattern # 18 - 97 Pathfinder A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 27
Pattern # 19 - 96 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 28
Pattern # 20 - 97 Quest A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 29
Pattern # 21 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 30
Pattern # 22 - 96 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 31
Pattern # 23 - 96 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 32
Pattern # 24 - 97 Sentra/200SX (GA 16DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 33
Pattern # 25 - 97 Sentra/200SX (GA 16DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 34
Pattern # 26 - 96-97 200SX (SR20DE) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 35
Pattern # 27 - 96-97 200SX (SR20DE) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 36
Pattern # 28 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 37
Pattern # 29 - 96 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 38
Pattern # 30 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 39
Pattern # 31 - 96 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 40
Pattern # 32 - 97 Truck (2WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 41
Pattern # 33 - 97 Truck (2WD) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 42
Pattern # 34 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 43
Pattern # 35 - 96 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 44
Pattern # 36 - 97 Truck (4WD) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 45
Pattern # 37 - 96 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 46
Pattern # 38 - 96 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 47
Pattern # 39 - 97 240SX M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 48
Pattern # 40 - 97 240SX A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 49
Pattern # 41 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 50
Pattern # 42 - 96 300ZX (Non-Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 51
Pattern # 43 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 52
Pattern # 44 - 96 300ZX (Non-Turbo) A/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 53
Pattern # 45 - 96 300ZX (Turbo) M/T
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 54
Pattern # 46 - 96 300ZX (Turbo) A/T
Monday, June 10, 2019
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-114B Date: 120614
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-114B Date: 120614
Tire Monitor System - Tire Inflation Information
Classification: WT 10-005B
Reference: NTB10-0114B
Date: June 14, 2012
INFLATING TIRES EQUIPPED WITH TPMS
The publication date on this bulletin has been amended to include the newest models.
APPLIED VEHICLE: All Nissan with Tire Pressure Monitor System (TPMS)
SERVICE INFORMATION
Improper use of tire inflator tools can break the stem of a Tire Pressure Monitor System (TPMS) sensor.
NOTE:
The type of stem breakage shown in Figure 1 is not considered a warrantable repair.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 120
Please refer to the following examples of recommended and not recommended tire pressure filling tools.
Not Recommended tire inflator tools.
Recommended tire inflating tools.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 121
Aftermarket Tire Sealers
2014 Nissan-Datsun Altima Diagrams. DTC # 09-040A Date: 100514
2014 Nissan-Datsun Altima Diagrams. DTC # 09-040A Date: 100514
Cooling System - Long Life Coolant Information
Classification: EM09-001A
Reference: NTB09-040A
Date: May 14, 2010
NEW BLUE NISSAN LONG LIFE ANTIFREEZE/COOLANT
This bulletin has been amended. The Service Information has been updated. Please discard previous versions of this bulletin.
SERVICE INFORMATION
In calendar year 2009, Nissan began filling some vehicles at the factory with a NEW Nissan Long Life Antifreeze/Coolant (LLC) that is blue in
color.
NOTE: LLC = Long Life Antifreeze/Coolant
The transition to this new Blue LLC continued though MY 2010. Beginning with MY 2011, all Nissan vehicles are filled at the factory with the Blue
LLC.
^ MY 2009 and 2010: Some vehicles are filled at the factory with Blue LLC.
^ MY 2011: All vehicles are filled at the factory with Blue LLC.
Blue LLC is designed to have a service life of 7 years/105,000 miles for the factory fill, and 5 years/75,000 miles for subsequent replacement fills.
Nissan Blue Super LLC is available through the Nissan Direct Ship Chemical Care Product Program, Website order link via dealer portal
www.NNAnet.com or order direct www.NissanChemicals.com.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 418
^ Blue LLC one gallon pre-diluted:
P/N 999MP - LP25500P
> The one gallon containers are pre-diluted with 50% antifreeze and 50% distilled water.
> Do not add additional water when using pre-diluted Blue LLC.
^ Blue LLC one quart concentrate:
P/N 999MP - L255QTP
> The one quart concentrate containers are intended for extreme cold weather application.
> Use the concentrate without mixing (do not add water).
> Add directly to the cooling system in specific amounts as directed on the container label.
Additional Information for using Blue LLC
Blue LLC and Green-colored Nissan LLC (P/N 999MP-AF000P) are compatible with each other:
^ Blue can be mixed/added with Green
^ Green can be mixed/added with Blue
CAUTION:
^ Adding Green LLC to Blue LLC will reduce/shorten the life expectancy of the Blue LLC to that of the Green LLC (4 years / 60,000 miles).
^ LLC must always be used with demineralized or distilled water, otherwise the life expectancy of the LLC (Blue or Green) will be degraded and
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 419
cooling system damage may occur.
Sunday, June 9, 2019
2017 Nissan-Datsun Altima Technical Service Bulletin # 11-090 Date: 111003
2017 Nissan-Datsun Altima Technical Service Bulletin # 11-090 Date: 111003
Power Locks - Auto Lock/Unlock Function Information
Classification: EL11-035
Reference: NTB11-090
Date: October 3, 2011
AUTO LOCK/UNLOCK FUNCTION
APPLIED VEHICLES: All 2010-2012 Nissan vehicles equipped with power door locks
SERVICE INFORMATION:
For testing purposes, both the auto-lock function and the auto-unlock function can be disabled or enabled independently of each other. Vehicles are
shipped from the factory with both features enabled.
The following information will confirm normal auto-lock and auto-unlock function and provide direction on how to temporarily disable and then
re-enable both of these features.
NOTE:
Some models may have additional functions that can only be changed with CONSULT. This bulletin only covers those features that can be changed
without CONSULT.
FUNCTION DESCRIPTION:
> Auto-lock with speed: All doors lock automatically when the vehicle speed reaches 15 mph. (24 km/h)
> Auto-unlock: All doors unlock automatically when the ignition is placed in the OFF position (models with Intelligent Key system) or when the
key is removed from the ignition switch (models without Intelligent Key system).
If there is a concern about how either of these functions operates:
1. Make sure that power locks work properly (confirm by pressing power lock and unlock switches)
2. See the procedures below to test the Auto-lock/unlock modes independently. Modes can also be tested with CONSULT. Refer to the appropriate
section of the Electronic Service Manual (ESM) for additional information.
IMPORTANT:
After testing or service, both auto-lock and auto-unlock features must be re-enabled before a vehicle is returned to the customer.
MODE CHANGE TEST PROCEDURE:
To change the AUTO-UNLOCK mode for testing purposes, perform the following procedure:
a. First, close all doors.
b. Then place the ignition switch in the ON position,
c. And do the following within 20 seconds of performing Step b:
> To change AUTO-UNLOCK settings, push and hold the power door lock switch to the unlock position for more than 5 seconds.
> The hazard warning lights will flash when the mode change is confirmed.
d. Turn the ignition switch OFF, and then back ON again.
To change the AUTO-LOCK mode for testing purposes, perform the following procedure:
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 206
a. First, close all doors.
b. Then place the ignition switch in the ON position,
c. And do the following within 20 seconds of performing Step b:
> To change AUTO-LOCK settings, push and hold the power door lock switch to the lock position for more than 5 seconds.
> The hazard warning lights will flash when the mode change is confirmed.
d. Turn the ignition switch OFF, and then back ON again.
NOTE:
^ When the auto-lock or auto-unlock function is disabled, the hazard warning lights will flash once. When the auto-lock or auto-unlock function is
enabled, the hazard warning lights will flash twice.
^ Only one mode change (auto-lock OR auto-unlock) per ignition cycle is allowed.
If the function does not perform as described here, refer to the appropriate ESM for further information.
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-003A Date: 100211
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-003A Date: 100211
A/T - 5 Speed A/T DTC Diagnostics
Classification: AT09-016A
Reference: NTB10-003A
Date: February 11, 2010
5 SPEED A/T DTC DIAGNOSES FOR P1701, P1702, P1703, P1704, P1705, P1754, P1759, P1764, P1769, P1774
This bulletin has been amended. Additional DTCs were applied. Discard all previous copies.
APPLIED VEHICLES: 2003 - 2010 Nissan vehicles with 5-Speed A/T
APPLIED TRANSMISSION: RE5R05A ONLY
SERVICE INFORMATION
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 409
If one or more DTCs listed below are found stored in Self Diagnosis, use the REPAIR FLOW CHART shown below to assist in diagnosis.
^ DTCs: P1701, P1702, P1703, P1704, P1705, P1754, P1759, P1764, P1769, P1774.
IMPORTANT NOTE:
If DTC(s) not listed above is/are found stored in Self Diagnosis, this bulletin does not apply. Refer to ASIST and the appropriate Service Manual for
diagnostic procedure(s) as needed.
Saturday, June 8, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-140 Date: 091208
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-140 Date: 091208
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 392
A/T - CVT Oil Leak Diagnosis Information
Classification: AT09-012
Reference: NTB09-140
Date: December 8, 2009
CVT OIL LEAK DIAGNOSIS USING FLORESCENT DYE
APPLIED TRANSMISSION: Continuously Variable Transmission (CVT)
SERVICE INFORMATION
If you have a CVT that appears to have oil seepage or a leak on the transmission, follow the steps below to assist in a correct diagnosis.
1. Thoroughly clean off the area of the suspected leak.
2. Install 1 fluid ounce of J-28431 Fluorescent Oil Dye* into the CVT.
3. Drive vehicle for a minimum of 30 minutes (to ensure proper diagnosis).
4. Inspect with lamp from J-43926 A/C Dye Kit*
If no fluorescent oil trace/leak is found, the stain is probably:
^ corrosion protection chemicals sprayed on the transmission
and/or
^ lubricants which are sometimes used to ease the assembly process.
NOTE:
These may cause dust to accumulate (gather) on the transmission and have the appearance of an oil leak. Neither of these requires corrective action.
If a fluorescent oil trace/leak is found:
^ Repair using standard warranty procedures.
*These tools were made Essential in 2001 (J-28431) and 1999 (J-43926). They are also available from Tech Mate.
NOTE:
The Fluorescent Oil Dye is also available from Tech Mate in a pack of six 1 ounce bottles. That pack is available as part number J-28431-6.
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-078 Date: 100621
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-078 Date: 100621
Engine Controls - ECM Programming Interruption Recovery
Classification: EC10-015
Reference: NTB10-078
Date: June 21, 2010
REPROGRAM INTERRUPTION RECOVERY PROCEDURE
SERVICE INFORMATION
A complete step-by-step General Procedure for CONSULT-III (C-III) ECM Reprogram Interruption Recovery is now available by attachment in this
bulletin.
While performing ECM (Engine Control Module) reprogramming, the reprogramming may stop (become interrupted) before it is 100% complete.
One of two messages may appear:
^ The VI probe is disconnected on USB, please check the connection of the probe.
^ Reprogramming fail, "Error code 0".
In many cases, reprogramming recovery is possible and the ECM may not need to be replaced if the complete ECM part number has been registered
into the ECM before reprogramming stopped.
NOTE:
ECM is referred to as ECU in C-III.
The ECM Reprogram Interruption Recovery General Procedure applies to Technical Service Bulletins that include ECM reprogramming published
in April 2010 and later.
IMPORTANT: BEFORE STARTING REPROGRAMMING
^ Connect a battery charger to the vehicle battery.
^ Be sure to turn OFF all vehicle electrical loads.
^ For ECM reprogramming, the C-III MUST be connected to the VI using the USB cable.
^ Be sure to connect the AC Adapter.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 253
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 254
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 255
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 256
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 257
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 258
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 259
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 260
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 261
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 262
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 263
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 264
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 265
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 266
2017 Nissan-Datsun Altima Technical Service Bulletin # 12-068 Date: 120820
2017 Nissan-Datsun Altima Technical Service Bulletin # 12-068 Date: 120820
CVT - Fluid Applications
Classification: AT12-006
Reference: NTB12-068
Date: August 20, 2012
NISSAN; CVT FLUID INFORMATION
APPLIED VEHICLES: All Nissan Vehicles Equipped with CVT
APPLIED TRANSMISSIONS: CVT
SERVICE INFORMATION
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 554
IMPORTANT:
When servicing a Nissan vehicle equipped with a Continuously Variable Transmission (CVT) make sure to use the appropriate Nissan CVT Fluid
specified in the Electronic Service Manual (ESM), Owners Manual or Service and Maintenance Guide. Using fluid other than that specified may
damage the CVT and is not covered by warranty.
^ NISSAN CVT Fluid NS-2 ("green fluid") - applies to all Nissan vehicles equipped with CVT except MY13 Altima. Use NS-2 green fluid to
service these vehicles.
^ New, unused service replacement CVTs may have some residual "blue" NS-3 fluid. However, these service replacement CVTs should be
filled with NS-2 green fluid. No draining is necessary.
^ NISSAN CVT Fluid NS-3 ("blue fluid") - applies to the 2013 Altima. Use NS-3 blue fluid to service these vehicles.
^ Use of any other type of fluid, including NS-2 green fluid, in the 2013 Altima vehicle may result in reduced fuel economy and/or affect
drivability.
Please refer to the table above, the ESM, Owners Manual or Service and Maintenance Guide.
Friday, June 7, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-103B Date: 121031
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-103B Date: 121031
Navi/Audio Visual - Control Unit Diagnosis And Ordering
Classification: EL11-043B
Reference: NTB11-103B
Date: October 31, 2012
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 55
PREMIUM NAVI / AUDIO VISUAL CONTROL UNIT DIAGNOSIS AND ORDERING
This bulletin has been amended by adding to the APPLIED VEHICLES list, and the procedure to obtain the A/V unit part number. Please discard all
previous versions of this bulletin.
APPLIED VEHICLES
SERVICE INFORMATION
To improve customer satisfaction by providing the correct repair on the first visit, Nissan has revised the procedure for ordering an "exchange" or
"new" Audio Visual (A/V) Control Unit for vehicles with the premium navigation systems only (Refer to PROCEDURE).
^ To ensure a proper diagnosis and repair, the technician will need to call TECH LINE to confirm (or assist with) their diagnosis and the proper
repair prior to ordering the unit.
^ Clarion will require a confirmation from TECH LINE prior to shipping the exchange unit orders.
^ For the premium navigation system only.
^ Parts will be put on parts restriction and will need to be cleared prior to the order shipping.
^ The warranty claims call center will verify that TECH LINE has recommended replacement as part of the approval process in the event that a new
unit is required.
> TECH LINE has the support of engineering and Clarion in diagnosis if required.
NOTE:
All other A/V units will be ordered and shipped through the normal process.
> As usual, most units ordered should be an exchange unit versus a new unit.
This requirement of calling TECH LINE for confirmation to replace an A/V unit will be monitored to ensure the most effective and accurate method
of repair. Future changes or adjustments may be made to this process to increase repair timeliness and/or customer satisfaction.
A NEW UNIT IS REQUIRED ONLY IF:
^ The vehicle has not yet been sold.
^ The customer requests a new unit on a non-warranty repair.
^ The exchange unit is not available.
^ Insurance claim replacement.
NOTE:
Nissan would also recommend that this procedure is used for non-warranty repairs to ensure that a proper diagnosis and repair are performed.
PROCEDURE
a. Verify and duplicate the customers concern if possible. If duplication is not possible, please gather as much information about the incident
as possible from the service advisor/writer or customer.
b. Check for any connected devices (phone, iPod, MP3 player, etc.) or determine if a connected device is present during the concern. Please
gather model and software version information if possible.
c. Perform NTB09-063 for any Bluetooth concerns and NTB11-096 for any iPod / iPhone music play through USB concerns.
d. After gathering preliminary information of the concern, please call TECH LINE. After a diagnosis of the concern has been performed, and
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 56
the technician and TECH LINE agree that the unit should be replaced, the dealer can order the part.
e. TECH LINE will confirm with Clarion that the diagnosis has occurred.
f. After the order is confirmed with Clarion, an order/shipping confirmation fax will be sent to the dealer.
g. Before an order is placed, the technician/dealer will need to provide TECH LINE with the following information from the incident unit:
Obtain A/V Unit Part Number (Optional)
Obtain A/V Unit Part Number (OPTIONAL)
1. Make sure the shift selector is in Park (A/T) or Neutral (M/T), and the parking brake is set.
2. Connect the plus VI to the vehicle.
3. Turn the ignition ON.
NOTE:
You may want to start the engine to keep the battery charged during this procedure.
4. Write down customers radio station presets (presets will be lost during this procedure).
5. Open/start ASIST on the CONSULT PC, and then select CONSULT III plus.
6. Wait for the plus VI to be detected, and the status box(es) to turn "green".
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 57
7. Select the plus VI with the correct serial number being used (if more than one in the shop) by highlighting it in the Connection Status box.
8. Select Re/programming Configuration.
9. Use arrows (if needed) to view and read all Cautions.
10. Check the box confirming the precautions have been read.
11. Select Next.
12. Select the Automatic Selection (VIN) tab.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 58
13. Select Confirm.
^ Wait while system call completes.
14. Select Confirm.
15. Select Multi A/V.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 59
16. Select Read / Write Configuration.
17. Select Before Replace ECU.
18. Select Save.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 60
^ The software P/N is shown in Figure 10. Ignore it.
19. Select End.
NOTE:
Leave C-III plus running and the plus VI connected.
20. Turn OFF the audio system.
21. Put the A/V system into System Diagnostic Mode as follows:
a. Press and hold the SETTING button.
b. While holding the SETTING button, turn the volume control knob 40 clicks or more.
^ The volume control knob can be turned either direction.
^ When the system goes into the System Diagnostic Menu, the screen in Figure 12 will display.
22. Select Confirmation/Adjustment.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 61
23. Select Delete Unit Connection Log.
24. Select Yes.
25. Select Initialize Settings.
26. Select Accessory Number Initialization.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 62
27. Select Yes.
28. Wait while the system "initializes".
^ The screen in Figure 18 will display while "initializing".
^ The screen in Figure 19 will display when "initialization" is complete.
29. Once "initialization" is complete, reboot the Multi A/V system as follows:
a. Turn OFF the ignition.
b. Wait 10 seconds.
c. Turn ON the ignition.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 63
30. Select Diagnosis (One System).
31. Select MULTI AV.
32. Select the ECU identification tab.
33. Print or write down the ECU PART NUMBER for ordering and warranty information:
25915-_ _ _ _ _
34. Select Home.
The A/V unit can now be ordered with this part number. The current A/V unit can now be configured for use until it is replaced.
Configure the Multi AV System
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 64
Configure the Multi AV System
1. After selecting Home, the screen in Figure 23 will appear.
2. Select Re/programming Configuration.
3. Read the Precautions.
^ When finished, touch the Confirmed instructions box to insert a check mark, and then select Next.
4. Select Automatic Selection (VIN).
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 65
5. Confirm the correct Model Name and Model Year are displayed.
^ When finished, select Confirm.
6. Select Confirm.
7. Select After Replace ECU.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 66
8. Select OK.
9. After selecting OK, the screen in Figure 30 appears.
10. Select End.
^ Configuration is now complete.
Close C-III plus, remove the plus VI, and then go to "Confirm Multi AV System is Operational".
Confirm Multi AV System Is Operational
Confirm Multi AV System Is Operational
1. Put your foot on the brake, and then turn the engine OFF (if running).
2. Start the engine, and then move the shift selector to R (Reverse).
3. If equipped, make sure the rear view monitor is working correctly.
4. Put the shift selector back into P (Park).
5. Turn ON the radio.
6. Turn the volume knob and make sure the audio volume responds to movement of the knob.
7. Reset the radio station presets.
The Nissan 370Z Nismo Is Outdated and Overpriced
Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-048B Date: 111003
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-048B Date: 111003
Keyless Systems/TPMS - SIGNAL TECH II(R) Diag. Tool
Classification: WT10-001B
Reference: NTB10-048B
Date: October 3, 2011
SIGNAL TECH II DIAGNOSTIC TOOL
This bulletin has been amended. The note below APPLIED VEHICLES was amended. Please discard previous versions of this bulletin.
APPLIED VEHICLES: All Nissan with Tire Pressure Monitor System (TPMS), Remote Keyless Entry, or Intelligent Key.
NOTE:
Failure to update Signal Tech II may lead to misdiagnosis of certain models.
^ The latest software is available on the CONSULT III PC at: ASIST> Specialty Tools > Signal Tech II
^ If you should encounter problems updating Signal Tech II, contact Techmate.
^ Future updates will be released as needed. Check ASIST frequently for this information.
SERVICE INFORMATION
If service is required on a vehicle's Tire Pressure Monitor System (TPMS), remote keyless entry, or Intelligent Key, the Signal Tech II (special tool
J-50190) can be used for diagnostics.
Signal Tech II will quickly:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 207
^ Activate and display TPMS Sensor IDs
^ Display tire pressure reported by the TPMS sensor
^ Read TPMS DTCs and register TPMS IDs
^ Store and print reports for warrantable repairs
^ Check Intelligent Key relative signal strength
^ Test remote keyless entry relative signal strength
^ Confirm vehicle Intelligent Key antenna relative signal strength output
^ Read ENGINE DTCs
Other available information for Signal Tech II:
^ Signal Tech II Quick Start Guide: ASIST> Tools & Equipment > Tool & Equipment Web Page
^ Signal Tech II Users Guide: ASIST > Tools & Equipment> Tools & Equipment Web Page
^ Tool Flyer: ASIST > Tools & Equipment > Tools & Equipment Web Page> Nissan Essential Tool Flyers
^ Tech Talk Article: ASIST > Tech Support Info> TECH TALK / XTRA> Spring 2010 issue
Thursday, June 6, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-070A Date: 130305
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 12-070A Date: 130305
Audio/Navigation System - Various Issues
Classification: EL12-060A
Reference: NTB12-070A
Date: March 5, 2013
2010 - 2014; NAVIGATION SYSTEM REBOOTS OR AUDIO CONTROLS WILL NOT RESPOND
This bulletin is being amended to update the Applied Vehicles information.
Please discard previous versions of this bulletin.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 538
APPLIED VEHICLES
IF YOU CONFIRM
One or more of the following is occurring on an Applied Vehicle:
^ Specific addresses cannot be entered
^ System reboots when:
> On long trips with a destination set
> Within a few minutes of starting the vehicle
^ A destination set or during the process of setting
> The logo appears after the system shuts off
^ System locks up with many functions occurring at one time (USB, Bluetooth, MP3, vehicle in reverse/camera operating, etc.).
^ POIs are missing (Application disc of new "map update" was not installed).
^ Popping noise from the vehicles speakers when ignition is turned on after entering the vehicle, if the customer was on a Bluetooth Handsfree call
that connected to the vehicle mid call.
NOTE:
Do not install this software update for Bluetooth Sound Quality concerns. Refer to bulletins NTB09-063, NTB12-105 or NTB12-106 to resolve.
^ Incoming call cannot be heard or received when using iPhone 5.
ACTION
^ Follow the Service Procedure to load the Re-programming Software DVD referenced in the Parts Information.
NOTE:
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 539
iPhone 5 "Incoming call cannot be heard or received" can also be resolved independently with the latest Apple iOS (phone operating system) update.
Please have customer update their iPhone: Settings>General>Software Updates.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
NOTE:
This procedure will take 10-20 minutes with the ignition ON and will require the DVD to be inserted twice to complete the update.
^ Before starting the procedure, make sure to attach a battery charger to the vehicle battery and set it to a low charge rate (trickle
charge).
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
^ The Navigation start-up screen should display.
^ If the Navigation start-up screen is not displayed: turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
3. Wait more than 1 minute.
4. Turn the Bluetooth OFF.
5. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
6. Load "NTB12-070/ITB12-054 Re-programming Software" DVD into CD slot of the audio unit.
^ For Altima, press the OPEN/TILT button to open the display and access the CD/DVD player slot. Leave the display open while loading.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 540
^ If the screen in Figure 1 is displayed, this update has already been performed and this bulletin does not apply.
> Turn the Bluetooth back ON and remove the DVD from the CD slot.
^ If "Now preparing loading" shown in Figure 2 is displayed, follow the on screen Caution while the Navigation is updated.
7. During the first part of the update process 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 3)
^ Rewriting program data (Figure 4)
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 541
^ Rewriting language data (Figure 5)
IMPORTANT:
Once the re-programming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
8. When the first part of the program has finished loading:
^ "Program loading is completed" will be display (Figure 6).
^ The Re-programming Software DVD will automatically eject.
9. Remove the DVD and continue to the second part of the update in step 10.
10. After the DVD is removed, the screen in Figure 7 "Please insert disc" may ask to reinstall the same Re-programming Software DVD for a
second time.
^ If not, the re-programming is complete. Proceed to step 13.
^ If so, re-insert DVD disc.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 542
> At the top of the screen "Program Loading (2nd)" will be displayed.
11. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.
IMPORTANT:
Once re-programming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
12. After the reprogram has completed:
^ "Program loading is completed" will be display (Figure 10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart.
^ Proceed to step 13.
After Navigation has restarted:
13. To confirm that the Navigation version has been successfully updated, load the DVD into the CD slot for a third time.
^ If Figure 1 is displayed it indicates that the re-program has been completed.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 543
> If complete go to step 14.
^ If Figure 2 is displayed, allow the update to complete (steps 7-12) and follow the on screen instructions, then perform step 13 to confirm
the re-program has completed.
14. Eject DVD.
15. Turn the Bluetooth back on.
16. The procedure is complete. Turn the ignition OFF.
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-003 Date: 090109
2017 Nissan-Datsun Altima Technical Service Bulletin # 09-003 Date: 090109
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 219
iPod(R) - Charging With Nissan Interface System
Classification: EL08-037
Reference: NTB09-003
Date: January 9, 2009
iPod(R) Charging with Nissan Interface System for iPod(R)
APPLIED VEHICLES: All Nissan with Nissan Interface System for iPod(R)
(factory installed or accessory installed)
SERVICE INFORMATION
Please be aware that a recent design change was made by Apple to their iPod(R) and iPhone(R) products. As a result of this change, some customers
may report that their iPod(R)/iPhone(R) device does not charge while connected to the Nissan Interface System for iPod(R).
The Nissan Interface System for iPod(R) was designed to charge the customer's iPod(R) with a 12-volt power source, which has been supported by
all Apple iPod(R) and iPhone(R) devices until the latest generation. After Apple's design change, these new devices only support charging via a
5-volt source, which the Interface System does not provide. Customers may see error messages on the device screen, or notice that the device's
battery discharges while connected to their vehicle's interface system. Please note that while charging may not be supported playback and control
through the vehicle's audio system are still available.
Compatible Devices:
All Apple devices that support charging via a FireWire(R) connection are compatible with the Nissan Interface System for iPod(R). These include:
^ iPod(R) Classic - 1st through 6th generation
^ iPod(R) Mini - 1st through 2nd generation
^ iPod(R) Nano - 1st through 3rd generation
^ iPod(R) Touch - 1st generation
^ iPhone(R) - 1st generation
NOTE:
Refer to the vehicle Owner's Manual for further Nissan Interface System Information.
Non-compatible devices (as of 12/8/2008):
^ iPhone(R)3G
^ iPod(R) Nano - 4th generation
^ iPod(R) Touch - 2nd generation
Nissan is working closely with Apple to ensure full compatibility with our future Interface Systems, but as Apple's change was made without
adequate notification to Nissan, at this time there is no plan to modify the current Interface Systems for the 2009 model year.
Please make customers aware that there are products available in the aftermarket designed to reduce the 12V power source to 5V and should enable
their device to charge while connected to their vehicle. A few examples are provided below, however, Nissan expects these types of aftermarket
solutions to become even more widely available considering that Apple's change has impacted the charging ability of many automotive OEM's
iPod(R) integration systems.
Aftermarket Solutions:
PLEASE NOTE:
Nissan has not tested any of these aftermarket solutions and makes no endorsement, warranty, or guarantee of performance or compatibility for any
specific third party accessory. These devices are advertised by their respective manufacturers to resolve 12V to 5V charging issues, but have not
been designed for or tested with Nissan vehicles.
^ Scosche Passport - http://www.scosche.com/passport
^ Cablejive Charge Converter - http://cablejive.com/iphone_3g_charge_converter.html
^ Ridax Charge Converter - http://home.swipnet.se/ridax/connector.html?connipod.htm
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 220
Customer Service:
For further questions and comments, customers may always feel free to contact Nissan Consumer Affairs at 1-800-647-7261.
Wednesday, June 5, 2019
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-043 Date: 110421
2019 Nissan-Datsun Altima Diagnostic and Repair Information # 11-043 Date: 110421
CVT - DTC P0725/P1722 Diagnostic Supplement
AT11-006
Reference: NTB11-043
Date: April 21, 2011
DIAGNOSTIC INFORMATION FOR DTC P0725 AND P1722
APPLIED VEHICLES: All Nissan 2007 and later (newer)
APPLIED TRANSMISSION: Equipped with CVT
SERVICE INFORMATION
When performing diagnostics for DTC P0725 (Engine Speed) and/or P1722 (Vehicle Speed), additional diagnostic steps to those in the Service
Manual are needed to arrive at a correct repair.
Using the diagnostic flow charts in this bulletin will direct you to the additional steps needed for correct diagnosis.
DO NOT replace the Transmission Control Module (TCM), unless all diagnostic steps in this bulletin check OK and the Service Manual diagnostic
steps direct TCM replacement.
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 314
2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 315
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-121B Date: 110912
2017 Nissan-Datsun Altima Technical Service Bulletin # 10-121B Date: 110912
CVT Controls - Low Speed Hesitation Or Surge
Classification: AT10-004B
Reference: NTB10-121B
Date: September 12, 2011
2007-2011 ALTIMA
SLIGHT VEHICLE HESITATION OR SURGE TYPE FEEL AT LOW SPEEDS
Table A was amended. Please discard previous versions of this bulletin.
APPLIED VEHICLE: 2007 - 2011 Altima (L32 and CL32) Sedan and Coupe
APPLIED TRANS: CVT only
APPLIED ENGINE: QR25 only
IF YOU CONFIRM
There is a slight vehicle hesitation type feel and/or a surge type feel when all of the following conditions are present:
^ Speed between 10 and 45 mph and
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 226
^ Transmission torque converter clutch is engaged (lock mode) and
^ Engine RPM between 1200 and 2000 and
^ Light acceleration
IMPORTANT NOTE:
Very slight vehicle hesitation type feel and/or surge type feel under these conditions are a normal operating characteristic of this vehicle and are
within design specifications for the vehicle. However, for those customers who are particularly sensitive to this characteristic of their vehicle, the
actions in this bulletin may be performed for customer satisfaction.
ACTIONS
1. Refer to Step 2 in the Service Procedure to confirm this bulletin applies to the vehicle you are working on.
2. If this bulletin applies, make sure the customer is informed of the Customer Information below.
3. If after informing the customer of the Customer Information, the customer voluntarily chooses to have the condition addressed with the
specification change, then:
^ Reprogram the TCM, and
^ Install the Torque Rod Service Kit listed in the Parts Information.
Customer Information
1. Very slight vehicle hesitation type feel and/or surge type feel under the conditions described on page one are a normal operating characteristic of
this vehicle and are within design specifications for the vehicle.
2. For those customers who are particularly sensitive to this characteristic of their vehicles, the transmission control module reprogramming
procedure described in this bulletin may be performed. However, the customer should be advised that this is a specification change and differs from
the original specification that exists on their vehicle.
3. If a customer voluntarily chooses to have this specification change made to their vehicle, they should be advised that their actual MPG may (or
may not) slightly decrease (up to 1 mpg) as a result, depending on their driving habits and other conditions.
PARTS INFORMATION
CLAIMS INFORMATION
Disclaimer
Service Procedure
SERVICE PROCEDURE
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 227
1. Connect CONSULT III (C-III) to the vehicle to begin the TCM reprogramming procedure.
^ If you are not familiar with the TCM reprogramming procedure, refer to CONSULT-III (C-III) Transmission Control Module (TCM)
Reprogramming and Initialization general procedure.
CAUTION
2. When you get to the TCM Reprogramming screen shown in Figure 1, confirm TCM reprogramming applies as follows.
A. On your C-III screen, look at the Part Number (P/N) column (see Figure 1).
^ Write down the P/N on the Repair Order.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 228
B. Compare the P/N you wrote down to the numbers in the Current TCM P/N column in Table A above.
^ If there is a match this bulletin applies. Continue with the reprogramming procedure.
NOTE:
If there are two lines (two reprogramming options) on your C-III screen, use the one with the message "Caution! Use ONLY with NTB10-121.
^ If there is not a match, this bulletin does not apply. Refer to ASIST for further diagnostic information.
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 229
3. If this bulletin applies and you have performed TCM reprogramming, the screen in Figure 2 displays when reprogramming is complete.
4. Make sure to erase DTCs from all systems.
NOTE:
During reprogramming, DTCs will set in several systems and must be erased.
5. Turn OFF C-III and disconnect it from the vehicle.
Install Torque Rod Service Kit
2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 230
6. Replace the torque rod and the lower torque rod (numbers 1 and 8 in Figure 3).
^ Refer to the Service Manual; section EM, for removal and installation information. Use the torque rods in the Service Kit (see Parts Information).