Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-003 Date: 090109

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-003 Date: 090109



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 219



iPod(R) - Charging With Nissan Interface System



Classification: EL08-037



Reference: NTB09-003



Date: January 9, 2009



iPod(R) Charging with Nissan Interface System for iPod(R)



APPLIED VEHICLES: All Nissan with Nissan Interface System for iPod(R)



(factory installed or accessory installed)



SERVICE INFORMATION



Please be aware that a recent design change was made by Apple to their iPod(R) and iPhone(R) products. As a result of this change, some customers



may report that their iPod(R)/iPhone(R) device does not charge while connected to the Nissan Interface System for iPod(R).



The Nissan Interface System for iPod(R) was designed to charge the customer's iPod(R) with a 12-volt power source, which has been supported by



all Apple iPod(R) and iPhone(R) devices until the latest generation. After Apple's design change, these new devices only support charging via a



5-volt source, which the Interface System does not provide. Customers may see error messages on the device screen, or notice that the device's



battery discharges while connected to their vehicle's interface system. Please note that while charging may not be supported playback and control



through the vehicle's audio system are still available.



Compatible Devices:



All Apple devices that support charging via a FireWire(R) connection are compatible with the Nissan Interface System for iPod(R). These include:



^ iPod(R) Classic - 1st through 6th generation



^ iPod(R) Mini - 1st through 2nd generation



^ iPod(R) Nano - 1st through 3rd generation



^ iPod(R) Touch - 1st generation



^ iPhone(R) - 1st generation



NOTE:



Refer to the vehicle Owner's Manual for further Nissan Interface System Information.



Non-compatible devices (as of 12/8/2008):



^ iPhone(R)3G



^ iPod(R) Nano - 4th generation



^ iPod(R) Touch - 2nd generation



Nissan is working closely with Apple to ensure full compatibility with our future Interface Systems, but as Apple's change was made without



adequate notification to Nissan, at this time there is no plan to modify the current Interface Systems for the 2009 model year.



Please make customers aware that there are products available in the aftermarket designed to reduce the 12V power source to 5V and should enable



their device to charge while connected to their vehicle. A few examples are provided below, however, Nissan expects these types of aftermarket



solutions to become even more widely available considering that Apple's change has impacted the charging ability of many automotive OEM's



iPod(R) integration systems.



Aftermarket Solutions:



PLEASE NOTE:



Nissan has not tested any of these aftermarket solutions and makes no endorsement, warranty, or guarantee of performance or compatibility for any



specific third party accessory. These devices are advertised by their respective manufacturers to resolve 12V to 5V charging issues, but have not



been designed for or tested with Nissan vehicles.



^ Scosche Passport - http://www.scosche.com/passport



^ Cablejive Charge Converter - http://cablejive.com/iphone_3g_charge_converter.html



^ Ridax Charge Converter - http://home.swipnet.se/ridax/connector.html?connipod.htm



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 220



Customer Service:



For further questions and comments, customers may always feel free to contact Nissan Consumer Affairs at 1-800-647-7261.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE