Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 12-068 Date: 120820

2017 Nissan-Datsun Altima Technical Service Bulletin # 12-068 Date: 120820



CVT - Fluid Applications



Classification: AT12-006



Reference: NTB12-068



Date: August 20, 2012



NISSAN; CVT FLUID INFORMATION



APPLIED VEHICLES: All Nissan Vehicles Equipped with CVT



APPLIED TRANSMISSIONS: CVT



SERVICE INFORMATION



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 554



IMPORTANT:



When servicing a Nissan vehicle equipped with a Continuously Variable Transmission (CVT) make sure to use the appropriate Nissan CVT Fluid



specified in the Electronic Service Manual (ESM), Owners Manual or Service and Maintenance Guide. Using fluid other than that specified may



damage the CVT and is not covered by warranty.



^ NISSAN CVT Fluid NS-2 ("green fluid") - applies to all Nissan vehicles equipped with CVT except MY13 Altima. Use NS-2 green fluid to



service these vehicles.



^ New, unused service replacement CVTs may have some residual "blue" NS-3 fluid. However, these service replacement CVTs should be



filled with NS-2 green fluid. No draining is necessary.



^ NISSAN CVT Fluid NS-3 ("blue fluid") - applies to the 2013 Altima. Use NS-3 blue fluid to service these vehicles.



^ Use of any other type of fluid, including NS-2 green fluid, in the 2013 Altima vehicle may result in reduced fuel economy and/or affect



drivability.



Please refer to the table above, the ESM, Owners Manual or Service and Maintenance Guide.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE