Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426

2014 Nissan-Datsun Altima Diagrams. DTC # 08-090B Date: 110426



Interior - Door Panel Looks Faded/Discolored



Classification: BT08-031B



Reference: NTB08-090B



Date: April 26, 2011



ALTIMA AND MAXIMA; DOOR PANEL LOOKS DISCOLORED / FADED



This bulletin has been amended. The APPLIED VEHICLES section has been revised. Please discard all previous versions.



APPLIED VEHICLES:



2007-2011 Altima Coupe, Sedan, and Hybrid (C/L32/HV)



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 312



2009-0211 Maxima (A35)



SERVICE INFORMATION



If a door panel looks discolored or faded as shown in Figure 1:



^ The probable cause is dirt buildup in the grain of the material. See below for details on how to clean the door panel.



NOTE:



^ Vehicle care and maintenance (cleaning) is not covered under warranty.



^ DO NOT replace the door panel when cleaning will solve the incident.



A soiled door panel can be cleaned as follows:



^ Following the instructions on the label, apply Nissan Vinyl and Leather Cleaner to the door panel surface.



^ Gently use a soft bristle brush to remove trapped dirt.



^ Spray the area with water.



^ Wipe the area clean using a clean cloth.



^ Repeat the cleaning procedure as needed.



After treating the soiled area, the door panel should be clean as shown in Figure 2.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 313

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE