Skip to main content

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-003A Date: 100211

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 10-003A Date: 100211



A/T - 5 Speed A/T DTC Diagnostics



Classification: AT09-016A



Reference: NTB10-003A



Date: February 11, 2010



5 SPEED A/T DTC DIAGNOSES FOR P1701, P1702, P1703, P1704, P1705, P1754, P1759, P1764, P1769, P1774



This bulletin has been amended. Additional DTCs were applied. Discard all previous copies.



APPLIED VEHICLES: 2003 - 2010 Nissan vehicles with 5-Speed A/T



APPLIED TRANSMISSION: RE5R05A ONLY



SERVICE INFORMATION



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 409



If one or more DTCs listed below are found stored in Self Diagnosis, use the REPAIR FLOW CHART shown below to assist in diagnosis.



^ DTCs: P1701, P1702, P1703, P1704, P1705, P1754, P1759, P1764, P1769, P1774.



IMPORTANT NOTE:



If DTC(s) not listed above is/are found stored in Self Diagnosis, this bulletin does not apply. Refer to ASIST and the appropriate Service Manual for



diagnostic procedure(s) as needed.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more