Nissan-Datsun 370Z Technical 11-005C Date: 130401 Navigation System - Map Data Update Index Classification:

 Nissan-Datsun 370Z Technical  11-005C Date: 130401
Navigation System - Map Data Update Index
Classification:
EL11-001c
Reference:
NTB11-005c
Date:
April 1, 2013
NAVIGATION MAP DATA UPDATE MATRIX
This bulletin has been amended. Information for 2012 vehicles has been added to the matrix. No other changes have been made. Please discard all
previous copies.
APPLIED VEHICLES:
2003-2012 Nissan vehicles equipped with Navigation system - except LEAF
SERVICE INFORMATION
Two methods are used to update/upgrade Navigation Map Data:
1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR
2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed.
Use the matrix to determine which method is utilized for each Applied Vehicle.
  Page 345
Disclaimer

Nissan-Datsun 370Z Technical 11-012B Date: 130215 Entertainment Systems - CD And DVD Player Concerns

 Nissan-Datsun 370Z Technical  11-012B Date: 130215
Entertainment Systems - CD And DVD Player Concerns
Classification:
EL11-004b
Reference:
NTB11-012b
Date:
February 15, 2013
CD & DVD PLAYER CONCERNS
This bulletin has been amended to include current vehicles. No other changes have been made.
Please discard all previous versions.
APPLIED VEHICLES:
All Nissan Vehicles with an Audio Compact Disc (CD) Player or Digital Video Disc (DVD) Player
SERVICE INFORMATION
If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated
CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs.
  Page 343
To aid in solving customer concerns, use the following guidelines when speaking to customers or inspecting incident vehicles.
^ Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged (see Figures 1 and 2).
Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors.
NOTE:
Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this Bulletin.
^ Instruct the customer to handle discs carefully when inserting/removing them from the Player. Hold them by the edges and do not bend them.
Always place them in the storage case when they are not being used (played). This will ensure that discs stay in top working order.
^ Customers must not use discs with adhesive labels. The label will loosen or peel and this can jam the Player.
^ Ensure that the customer only uses audio CDs that have the "Compact Disc Digital Audio" insignia on them (see Figure 3). The audio CD Player
was designed to use CDs that meet this design standard. Lower quality CDs may not function properly in the audio CD Player.
^ Inform the customer that this information and additional disc care and cleaning instructions may be found in all Nissan Owner's Manuals.
  Page 344
Disclaimer

Nissan-Datsun 370Z Technical 09-020E Date: 130404 Emissions - EVAP System DTC Diagnosis Supplement Classification:

 Nissan-Datsun 370Z Technical  09-020E Date: 130404
Emissions - EVAP System DTC Diagnosis Supplement
Classification:
EC09-001e
Reference:
NTB09-020e
Date:
April 14, 2013
EVAP LEAK DTC DIAGNOSIS
This bulletin has been amended to the APPLIED VEHICLES section. Please discard all previous versions of this bulletin.
APPLIED VEHICLES:
2007 - 2014 Nissan vehicles SERVICE INFORMATION
  Page 337
  Page 338
  Page 339
  Page 340
If one or more DTCs listed below related to EVAP system leaks is found stored in Self Diagnosis, use the REPAIR FLOW CHART. Use the EVAP
system diagram for reference.
^ DTCs: P0442, P0455, and P0456
^ This Service Procedure can be used in addition to the procedure(s) outlined in the applicable Service Manual, and other bulletins applicable
to specific EVAP leak DTCs when necessary.
^ If a "Smoke (Leak Detection) Machine is available and preferred, the REPAIR FLOW CHART can still be used. This tool would be used in
place of watching for pressure drop and spraying with soapy water. Refer to the Machine's Operator's Manual for proper use.
CAUTION:
Use Essential Tool J-42909 (sent out to dealers September 1997) or equivalent to pressurize the EVAP system. Do Mot pressurize over the
amount specified in the applicable Service Manual. Do NOT use shop air pressure.
IMPORTANT NOTE:
If an EVAP system DTC(s) not related to EVAP leaks is/are found stored in Self Diagnosis, this bulletin does not apply. Refer to ASIST and
the appropriate Service Manual for diagnostic procedure(s) as needed.
  Page 341
  Page 342
CLAIMS INFORMATION
Disclaimer

Nissan-Datsun 370Z Technical 12-070A Date: 130305 Audio/Navigation System - Various Issues Classification: EL12-060A

Nissan-Datsun 370Z Technical  12-070A Date: 130305
Audio/Navigation System - Various Issues
Classification: EL12-060A
Reference: NTB12-070A
Date: March 5, 2013
2010 - 2014; NAVIGATION SYSTEM REBOOTS OR AUDIO CONTROLS WILL NOT RESPOND
This bulletin is being amended to update the Applied Vehicles information.
Please discard previous versions of this bulletin.
  Page 331
APPLIED VEHICLES
IF YOU CONFIRM
One or more of the following is occurring on an Applied Vehicle:
^ Specific addresses cannot be entered
^ System reboots when:
> On long trips with a destination set
> Within a few minutes of starting the vehicle
^ A destination set or during the process of setting
> The logo appears after the system shuts off
^ System locks up with many functions occurring at one time (USB, Bluetooth, MP3, vehicle in reverse/camera operating, etc.).
^ POIs are missing (Application disc of new "map update" was not installed).
^ Popping noise from the vehicles speakers when ignition is turned on after entering the vehicle, if the customer was on a Bluetooth Handsfree call
that connected to the vehicle mid call.
NOTE:
Do not install this software update for Bluetooth Sound Quality concerns. Refer to bulletins NTB09-063, NTB12-105 or NTB12-106 to resolve.
^ Incoming call cannot be heard or received when using iPhone 5.
ACTION
^ Follow the Service Procedure to load the Re-programming Software DVD referenced in the Parts Information.
NOTE:
  Page 332
iPhone 5 "Incoming call cannot be heard or received" can also be resolved independently with the latest Apple iOS (phone operating system) update.
Please have customer update their iPhone: Settings>General>Software Updates.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
NOTE:
This procedure will take 10-20 minutes with the ignition ON and will require the DVD to be inserted twice to complete the update.
^ Before starting the procedure, make sure to attach a battery charger to the vehicle battery and set it to a low charge rate (trickle
charge).
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
^ The Navigation start-up screen should display.
^ If the Navigation start-up screen is not displayed: turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
3. Wait more than 1 minute.
4. Turn the Bluetooth OFF.
5. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
6. Load "NTB12-070/ITB12-054 Re-programming Software" DVD into CD slot of the audio unit.
^ For Altima, press the OPEN/TILT button to open the display and access the CD/DVD player slot. Leave the display open while loading.
  Page 333
^ If the screen in Figure 1 is displayed, this update has already been performed and this bulletin does not apply.
> Turn the Bluetooth back ON and remove the DVD from the CD slot.
^ If "Now preparing loading" shown in Figure 2 is displayed, follow the on screen Caution while the Navigation is updated.
7. During the first part of the update process 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 3)
^ Rewriting program data (Figure 4)
  Page 334
^ Rewriting language data (Figure 5)
IMPORTANT:
Once the re-programming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
8. When the first part of the program has finished loading:
^ "Program loading is completed" will be display (Figure 6).
^ The Re-programming Software DVD will automatically eject.
9. Remove the DVD and continue to the second part of the update in step 10.
10. After the DVD is removed, the screen in Figure 7 "Please insert disc" may ask to reinstall the same Re-programming Software DVD for a
second time.
^ If not, the re-programming is complete. Proceed to step 13.
^ If so, re-insert DVD disc.
  Page 335
> At the top of the screen "Program Loading (2nd)" will be displayed.
11. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.
IMPORTANT:
Once re-programming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
12. After the reprogram has completed:
^ "Program loading is completed" will be display (Figure 10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart.
^ Proceed to step 13.
After Navigation has restarted:
13. To confirm that the Navigation version has been successfully updated, load the DVD into the CD slot for a third time.
^ If Figure 1 is displayed it indicates that the re-program has been completed.
  Page 336
> If complete go to step 14.
^ If Figure 2 is displayed, allow the update to complete (steps 7-12) and follow the on screen instructions, then perform step 13 to confirm
the re-program has completed.
14. Eject DVD.
15. Turn the Bluetooth back on.
16. The procedure is complete. Turn the ignition OFF.
Disclaimer

Nissan-Datsun 370Z Technical 11-073A Date: 130128 Campaign P1234 - Navigation Software Update For Various Issues Page 315 Reference:

Nissan-Datsun 370Z Technical  11-073A Date: 130128
Campaign P1234 - Navigation Software Update For Various Issues
  Page 315
Reference:
NTB11-073a
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN CALL WAITING FUNCTION NAVIGATION UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
CAMPAIGN ID #: P1234
APPLIED VEHICLES:
2010-2011 Altima Sedan, Coupe, and Hybrid (L32, CL32, & L32HV)
2010-2011 Maxima (A35)
2010 - 2011 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, iPod(R), and voice recognition functions may not be working as intended. To
remedy this potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or
labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system.
IDENTIFICATION NUMBER
Nissan has assigned identification number P1234 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for 2010 models in this campaign.
^ Do not use disc 3/3.
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
  Page 316
^ This disc also replaces disc NTB10-125b / ITB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-800-347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
For 2011 Models refer to 2011 Models - Installing the Navigation Update
2010 Models - Installing the Navigation Update
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function, otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
For 2010 models there are three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program
C. Check Bluetooth(R) Setting
A: Disable Bluetooth(R) Function
1. Set the parking brake.
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING" button on the switch panel.
  Page 317
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program -2010 Models
NOTE:
For 2011 Models, refer to 2011 Models - Installing the Navigation Update.
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
  Page 318
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No.1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD / DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB10-068 (Disc 1/3) into the in-dash CD/DVD player.
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
  Page 319
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
  Page 320
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
^ If "Now preparing loading shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
  Page 321
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the reprogram has finished loading:
  Page 322
^ "Program loading is completed will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update - step 22.
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
  Page 323
23. "Rewriting boot data" (Figure 20) and "Rewriting program data" (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
  Page 324
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting - 2010 Models
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
  Page 325
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
2011 Models - Installing the Navigation Update
NOTE:
This procedure will take 10 - 15 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set
to a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral (parking brake ON).
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
5. Load the new disc "NTB12-070/1TB12-054 Re-programming Software DVD into the CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Procedure is complete.
  Page 326
^ If "Now preparing loading shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on screen Caution during the reprogram.
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
  Page 327
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the program has finished loading:
^ "Program loading is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update - step 9.
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
  Page 328
10. "Rewriting boot data and "Rewriting program data will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 back into the CD slot again.
One of the following screens will display:
^ If Figure A11 is displayed, it indicates that the re-program has been completed.
  Page 329
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 5 through 12 again.
13. Eject the DVD.
14. Turn the ignition OFF. Procedure is complete.
  Page 330

Nissan-Datsun 370Z Technical 10-068E Date: 130128 Campaign P0337 - Navigation Software Update For Various Issues Reference: NTB10-068e

 Nissan-Datsun 370Z Technical  10-068E Date: 130128
Campaign P0337 - Navigation Software Update For Various Issues
Reference:
NTB10-068e
  Page 299
Date:
January 28, 2013
VOLUNTARY SERVICE CAMPAIGN
NISSAN NAVIGATION SOFTWARE UPDATE
This bulletin has been amended. Changes have been made throughout to accommodate a new reprogramming disc. Please discard previous versions
of this bulletin.
CAMPAIGN ID #: P0337
APPLIED VEHICLES:
2010 Altima Sedan, Coupe, and Hybrid (L32, CL32, and L32HV)
2010 Maxima (A35)
2010 370Z Coupe and Roadster (Z34 and HZ34)
2011 GT-R (R35)
Check Service Comm to confirm campaign eligibility.
INTRODUCTION
On the Applied Vehicles listed above, the navigation, mobile phone, and iPod(R) functions may not be working as intended. To remedy this
potential condition, Nissan is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number P0337 to this campaign. This number must appear on all communications and documentation of any
nature dealing with this campaign.
DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private
parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer's inventory.
REPROGRAMMING SOFTWARE DVDs - REQUIRED FOR THIS PROCEDURE
^ Discs 1/3 and 2/3 of the set shown in Figure A are used for all applied models in this campaign except GT-R.
^ Do not use disc 3/3.
  Page 300
^ This NEW disc (Figure B) is required for all applied models in this campaign.
^ This disc replaces disc 3/3 above.
^ This disc also replaces disc NTB10-125b/NTB10-066b (disc 1/1) and disc NTB10-068 (disc 1/1) for GT-R.
NOTE:
Numbers on these discs do not match this bulletin's reference number or the campaign ID #.
^ Each dealer was previously mailed the discs listed above, free of charge, from Clarion.
^ Should you require additional discs due to loss or damage, the discs can be ordered, free of charge, by contacting Clarion at the toll free number
1-(800) 347-8933. Request a new disc using the information printed on the disc.
CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the claims coding:
Service Procedure
IMPORTANT:
Before loading the Reprogram Discs, make sure to Disable Bluetooth(R) function otherwise the Navigation System may continuously reboot the
next time it is turned on.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
This SERVICE PROCEDURE contains three sections:
A. Disable Bluetooth(R) Function
B. Loading the Program - all except GT-R
Loading the Program for GT-R
C. Check Bluetooth(R) Setting - all except GT-R
Check Bluetooth(R) Setting for GT-R
A: Disable Bluetooth(R) Function
1. Set the parking brake.
  Page 301
2. Turn the ignition ON and keep the transmission in Park or Neutral.
3. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
4. Press the "SETTING button on the switch panel.
5. Touch "Bluetooth".
6. Make sure Bluetooth is OFF.
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is OFF when the ON indicator is "grayed-out".
7. Turn the ignition OFF and wait for 10 seconds.
8. Go to B: Loading the Program.
B: Loading the Program - all except GT-R For GT-R.
NOTE:
This procedure will take about 30 minutes with the ignition ON. Before starting, make sure to attach a battery charger to the vehicle battery set to
a low charge rate (trickle charge).
1. Turn the ignition ON - keep the transmission in Park or Neutral.
^ The navigation start-up screen should display.
  Page 302
NOTE:
If the navigation start-up screen is not displayed; turn the ignition OFF, wait 10 seconds, and then turn the ignition ON again.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Select "Navigation Version" on the display screen.
5. Check "Map Version".
^ If the Map Version is 09-10 MAP No. 1 or 09-10 MAP No.1a
a. Continue with Step 6.
^ If the Map Version is any other then above:
a. Insert the new disc NTB12-070 / ITB12-054 (Disc 1/1) into the in-dash CD/DVD player.
The other Discs will not be needed.
b. Skip to step 18.
6. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
7. Insert disc ITB10-031 / NTB1-0068 (Disc 1/3) into the in-dash CD/DVD player.
  Page 303
^ For Altima; open the display by pressing the OPEN/TILT button to access the disc slot. Leave the display open while loading.
IMPORTANT:
Once reprogramming has started:
^ Do not eject a disc while it is loading.
^ Do not change the ignition position until all discs have been loaded.
^ Make sure all 3 discs have been loaded into the CD/DVD player before stopping the procedure.
8. Wait for the program to load (progress bar will display).
9. When the program has finished loading:
^ Disc will automatically eject, and
^ "Program loading is completed" will display.
10. Carefully remove the disc.
11. The navigation system will automatically restart.
12. When the message Please insert Disc 2/3 displays, insert disc ITB10-031 / NTB10-068 (Disc 2/3).
13. Touch "DVD update".
  Page 304
14. Touch "Yes" to begin the map update process.
^ Map update will take about 15 minutes.
15. When "Eject the DVD to let the system reboot is displayed, eject Disc 2/3.
16. The navigation system will automatically restart.
17. When the message Please insert Disc 3/3 displays, insert the new disc NTB12-070 / ITB12-054 (Disc 1/1).
18. With DVD disc NTB12-070 / ITB12-054 (Disc 1/1) inserted, one of the following screens will display:
^ If the screen in Figure 13 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to C: Check Bluetooth(R) Setting.
  Page 305
^ If "Now preparing loading" shown in Figure 14 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
19. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure 15)
^ Rewriting program data (Figure 16)
^ Rewriting language data (Figure 17)
  Page 306
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
20. When the first part of the program has finished loading:
^ "Program loading is completed" will be displayed (Figure 18).
^ The Re-programming Software DVD will automatically eject.
21. Remove the DVD and continue to the second part of the update (step 22).
22. After the DVD is removed, the screen in Figure 19 ("Please insert disc") may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 25 on the next page.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
  Page 307
23. "Rewriting boot data (Figure 20) and "Rewriting program data (Figure 21) will be displayed.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
24. After the reprogram has completed:
^ "Program loading is completed will be displayed (Figure 22).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 25.
After Navigation has restarted:
25. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure 23 is displayed, it indicates that the reprogram has been completed.
  Page 308
> If complete, go to step 26.
^ If Figure 24 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 18.
> Follow steps 18 through 25 again.
26. Eject the DVD.
27. Go to C: Check Bluetooth(R) Setting.
C: Check Bluetooth(R) Setting (all except GT-R)
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
  Page 309
^ Bluetooth is OFF when the ON indicator is "grayed-out".
4. Turn the ignition OFF. The process is complete.
B: Loading the Program for GT-R
1. Turn the ignition ON.
2. Wait for more than 1 minute.
3. Press the "INFO" button on the switch panel.
4. Make sure there is no disc in the CD/DVD slot (eject any disc that may be in the CD/DVD player).
5. Load the new disc "NTB12-070/ITB12-054 Re-programming Software DVD into CD slot of the audio unit.
One of the following screens will display:
^ If the screen in Figure A1 is displayed, this disc is not needed.
> Remove/eject the DVD from the CD slot.
> Go to Check Bluetooth(R) Setting for GT-R.
^ If "Now preparing loading" shown in Figure A2 is displayed, reprogramming will begin automatically.
> Follow the on-screen Caution during the reprogram.
  Page 310
6. During the first part of the update process, 3 more screens will be displayed along with a percentage of completion (progress) bars:
^ Rewriting boot data. (Figure A3)
^ Rewriting program data (Figure A4)
^ Rewriting language data (Figure A5)
IMPORTANT:
Once the reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
7. When the first part of the reprogram has finished loading:
  Page 311
^ "Program loading" is completed will be displayed (Figure A6).
^ The Re-programming Software DVD will automatically eject.
8. Remove the DVD and continue to the second part of the update (step 9).
9. After the DVD is removed, the screen in Figure A7 (Please insert disc) may ask to reinstall the same Re- programming Software DVD for a
second time.
^ If not (Navigation System restarts), go to step 12.
^ If so, re-insert DVD disc.
> At the top of the screen "Program Loading (2nd)" will be displayed.
  Page 312
10. "Rewriting boot data" and "Rewriting program data" will be displayed once the DVD is reinstalled.
IMPORTANT:
Once reprogramming has started:
^ Do not eject the DVD while it is loading.
^ Do not change the ignition position until the DVD has been loaded.
11. After the reprogram has completed:
^ "Program loading is completed" will be display (Figure A10).
^ The Re-programming Software DVD will automatically eject.
^ The Navigation system will restart. Proceed to step 12.
After Navigation has restarted:
12. To confirm that the Navigation version has been successfully updated, load DVD disc NTB12-070 / ITB12-054 (Disc 1/1) back into the CD
slot again.
One of the following screens will display:
^ If Figure A11 is displayed it, indicates that the reprogram has been completed.
  Page 313
> If complete go to step 13.
^ If Figure A12 is displayed, the update did not complete. Allow the update to complete:
> Go back to step 5.
> Follow steps 6 through 12 again.
13. Eject the DVD.
14. Go to C: Check Bluetooth(R) Setting for GT-R.
C: Check Bluetooth(R) Setting for GT-R
1. Press the "Setting button on the switch panel.
2. Touch "Bluetooth".
3. Make sure Bluetooth is set to the customer's setting (as it was before starting the procedure).
^ Touching Bluetooth will change the setting ON > OFF or OFF > ON.
^ Bluetooth is ON when the ON indicator displays in orange.
  Page 314
^ Bluetooth is OFF when the ON indicator is "grayed out".
4. Turn the ignition OFF. The process is complete.

Nissan-Datsun 370Z Technical 13-015 Date: 130215 Keyless Systems - MIL ON, DTC B2190 Set

Nissan-Datsun 370Z Technical  13-015 Date: 130215
Keyless Systems - MIL ON, DTC B2190 Set
Classification:
EL13-004
Reference:
NTB13-015
Date:
February 15, 2013
MIL ON WITH DTC B2190
APPLIED VEHICLES:
All Nissan equipped with a Key-Slot for an Intelligent Key
SERVICE INFORMATION
DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons:
1. Something other than an Intelligent Key is inserted into the Key-Slot.
2. An Intelligent Key issue.
3. A wiring issue between the Key-Slot and the BCM.
4. A Key-Slot issue.
If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the
Key-Slot.
For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure.
Service Manual DTC CONFIRMATION PROCEDURE for DTC B2190
Disclaimer

Nissan-Datsun 370Z Technical 12-055B Date: 130322 Drivetrain - Front/Rear Axle Clicking Noise On Take Off

 Nissan-Datsun 370Z Technical  12-055B Date: 130322
Drivetrain - Front/Rear Axle Clicking Noise On Take Off
Classification: FA12-001B
Reference: NTB12-055B
Date: March 22, 2013
2007-2013; CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION
This bulletin has been amended to add additional models and to also include some independent rear suspension models.
APPLIED VEHICLES
IF YOU CONFIRM:
Customers concern of a "clicking" noise coming from either left or right front/rear axles during take-off/acceleration.
ACTION:
Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces.
NOTE:
^ Do not remove the axle from the hub or transmission for this bulletin
^ Refer to the Electronic Service Manual (ESM) for model specific torque specifications.
> Please see Service procedure for 2007-2011 Versa torque specifications
IMPORTANT:
The purpose of "ACTION" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service
Procedure as it contains information that is essential to successfully completing the repair.
  Page 296
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
NOTE:
The photos in this procedure are examples and may not look exactly like the vehicle you are working on.
  Page 297
1. Remove the front or rear (depending on model) wheel bearing Cotter Pin and Lock Nut from the axle.
NOTE:
Do not remove the axle from the hub or transmission for this bulletin.
2. Push axle back to allow application of Molykote M77 Grease.
3. Apply a moderate coat of Molykote (P/N 44003-7S000) to the entire (front or rear) wheel hub bearing surface (see Figure 2).
4. Re-install the (front or rear) wheel bearing Lock Nut and Cotter Pin per the Service Manual instructions.
^ Refer to model specific ESM for Lock Nut replacement requirements.
^ Refer to the model specific ESM for wheel bearing Lock Nut torque specifications.
IMPORTANT (for 2007 - 2011 Versa C11/N17 only):
> For 2007-2011 Versa tighten the center locknut to 180 N-m (18.4 kg-m, 133 ft-lb) with a torque wrench.
^ If the center locknut is tightened more than 180 N-m (18.4 kg-m, 136 ft-lb), the clicking noise could occur.
^ If the center locknut is tightened less than 180 N-m (18.4 kg-m, 133 ft-lb), looseness could occur.
^ If the center locknut is reused, the clicking noise could occur.
5. Test drive the vehicle to confirm the incident is resolved.
Disclaimer
  Page 298

Nissan-Datsun 370Z Technical 99-001A Date: 130319 Suspension - Strut and Shock Absorber Replacement Guidelines

 Nissan-Datsun 370Z Technical  99-001A Date: 130319
Suspension - Strut and Shock Absorber Replacement Guidelines
Classification:
FA99-001a
Reference
NTB99-001a
Date:
March 19, 2013
STRUT AND SHOCK ABSORBER
REPLACEMENT GUIDELINES
This bulletin has been amended. The Applied Vehicles section has been updated and revisions have been made throughout. Please discard earlier
versions.
APPLIED VEHICLES:
All 1990-2013 Nissan vehicles except those listed
This bulletin does not apply to:
All GT-R (R35) vehicles
Armada (TA60) - vehicles equipped with rear-leveling air suspension
SERVICE INFORMATION
This bulletin provides information to identify:
^ A leaking strut or a shock absorber that qualifies for replacement under warranty.
^ A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation
or performance, and does not require replacement.
^ A strut or shock absorber that should be replaced due to rod resistance/noise issues.
IMPORTANT:
^ If strut/shock absorber leakage is diagnosed in one strut/shock absorber, do NOT automatically replace struts/shock absorbers on both sides.
  Page 294
Replace the leaking strut/shock absorber only.
^ In cases where diagnosis of a strut indicates part replacement and the labor operation states that it includes toe or alignment check/set, the
alignment check/set must be supported with a printout from your alignment machine (i.e., "alignment printout").
Inspect the Condition of Oil Leakage
If oil does NOT extend beyond the spring seat or upper 1/3 of shock:
^ This is slight oil seepage. The strut/shock absorber should NOT be replaced.
If oil does extend beyond the spring seat or upper 1/3 of shock:
^ Use a finger to touch the oil that has extended beyond the spring seat or upper 1/3 of shock.
^ If you confirm the oil layer is thick and contains large pieces of dust and debris, the strut/shock absorber should be replaced.
^ If you confirm the oil layer is thin and does NOT contain large pieces of dust and debris, the strut/shock absorber should NOT be replaced.
  Page 295
Inspect the Strut/Shock Absorber Rod
CAUTION:
The front shock absorbers for Frontier (D40), Xterra (N50), and Pathfinder (R51) vehicles do NOT have a bound stopper inside. Make sure
to stop the rod close to the end of travel when compressing during step 1.
1. Compress and extend the strut rod or shock absorber rod more than four (4) times by hand.
2. Confirm the resistance and sound is normal when operating.
^ If atypical resistance or sound is noted, the strut/shock absorber should be replaced.
Disclaimer

Nissan-Datsun 370Z Technical 12-106A Date: 121219 Cell Phone - Poor Hands Free Phone Sound Quality Classification:

Nissan-Datsun 370Z Technical  12-106A Date: 121219
Cell Phone - Poor Hands Free Phone Sound Quality
Classification:
EL12-079a
Reference:
NTB12-106a
Date:
December 19, 2012
HANDS-FREE PHONE POOR SOUND QUALITY
The Applied Vehicles and Parts Information in this bulletin have been amended. Please discard previous versions.
APPLIED VEHICLES:
  Page 291
APPLIED VINs and DATES
IF YOU CONFIRM
The customer has experienced or is experiencing, while using the hands-free phone, people on the other end of a phone call cannot hear them.
The customer's experience may include:
^ Voice is choppy or cuts-out.
^ Voice sounds distant.
^ Voice sounds as if speaking through a tunnel.
^ Voice sounds like it is under water.
ACTION
1. Replace the TEL Adaptor Unit.
  Page 292
2. Replace the microphone and the map lamp finisher.
^ For Juke, replace the microphone and microphone finisher.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure
as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the claims coding shown.
SERVICE PROCEDURE
1. Replace the TEL Adaptor Unit.
  Page 293
^ Refer to the AV section in the appropriate Service Manual for replacement information.
2. Replace the Microphone.
^ Refer to the AV section in the appropriate Service Manual for microphone replacement information.
CAUTION:
Be careful not to crease the headlining.
^ Make sure to use the new microphone listed in the Parts Information.
^ Make sure to use the new map lamp finisher listed in the Parts Information.
NOTE:
For Juke use a new microphone finisher with new fasteners listed in the Parts Information.
IMPORTANT:
Make sure the new microphone is firmly snapped into place. If the microphone is loose, it could pick up extra noise from an unintended
source.
Disclaimer

Nissan-Datsun 370Z Technical 12-105A Date: 121219 Cell Phone - Poor Hands Free Phone Sound Quality

 Nissan-Datsun 370Z Technical  12-105A Date: 121219
Cell Phone - Poor Hands Free Phone Sound Quality
Classification:
EL12-078a
Reference:
NTB12-015a
Date:
December 19, 2012
2011-13 MURANO & 2010-13 370Z WITH NAVIGATION SYSTEM
HANDS-FREE PHONE POOR SOUND QUALITY
The Applied Vehicles and Parts Information in this bulletin have been amended. Please discard previous versions.
APPLIED VEHICLES:
  Page 275
APPLIED VINs and DATES
IF YOU CONFIRM
The customer has experienced or is experiencing, while using the hands-free phone, people on the other end of a phone call cannot hear them.
The customer's experience may include:
^ Voice is choppy or cuts-out.
^ Voice sounds distant.
^ Voice sounds as if speaking through a tunnel.
^ Voice sounds like it is under water.
ACTION
1. Reprogram (reconfigure) the Multi AV.
2. Replace the microphone and the map lamp finisher.
IMPORTANT:
The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service
Procedure as it contains information that is essential to successfully completing this repair.
  Page 276
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the claims coding shown.
REPAIR OVERVIEW
SERVICE PROCEDURE
NOTE:
^ Before starting, make sure your AS 1ST has been freshly synchronized and all CONSULT-III (C-III) plus upgrades have been installed.
^ The Multi-AV reprogramming (reconfigure) software is delivered to C-III plus via ASSIST synchronization.
There are six parts to this procedure:
Part 1: Using C-III plus - record (write down) the Multi AV control unit part number and configuration settings.
Part 2: Using the vehicles on-board Systems Diagnostic Menu - perform Multi AV initialization.
Part 3: Using C-III plus - reprogram (reconfigure) the Multi AV and confirm the control unit part number has changed.
Part 4: Make sure the Multi AV system is operational.
  Page 277
Part 5: Replace the system microphone with the one from the Parts Information section of this bulletin and install a new map lamp finisher.
Part 6: Check microphone operation using the vehicles on-board Systems Diagnostic Menu.
Part 1: Using C-III plus - record (write down) the Multi AV control unit part number and configuration settings.
1. Make sure the shift selector is in Park, and the parking brake is set.
2. Connect the C-III plus VI to the vehicle.
3. Turn the ignition ON.
NOTE:
You may want to start the engine to keep the battery charged during parts 1 through 4 of this procedure.
4. Write down the customer's radio station presets. (Presets will be lost during this procedure.)
5. Open/start AS 1ST on the CONSULT PC, then select CONSULT-III plus.
6. Wait for the VI to be detected, and status box to turn "green (Figure 1).
7. Select detected VI.
^ If there is more than one VI in the shop, select the VI that is being used on the current vehicle by highlighting the Connection Status box that
has the correct serial number.
8. Select Diagnosis (One System).
9. Select MULTI AV.
  Page 278
10. Select ECU Identification.
* IMPORTANT*
11. Print or write down the ECU PART
NUMBER for Warranty Information.
25915 - _________
NOTE:
In Part 3 of this procedure the ECU Part Number will be used to confirm the Multi AV reconfiguration was successful.
12. Select the Home button when done.
13. Select Re/programming Configuration.
  Page 279
14. Check the box confirming the precautions have been read, then select Next.
15. Use Manual Selection (Vehicle Name), then select correct Make, Model and Year.
NOTE:
If the screen in Figure 6 does not display, skip to step 17.
16. Click on Select.
17. Confirm correct VIN, Vehicle Name and Model Year.
18a. If the VIN is correct, select Confirm.
  Page 280
18b. If the VIN needs to be changed:
a. Select Change then refer to Figure 8.
b. Correct the VIN, and then select Confirm.
19. After system call completes, select MULTI AV.
20. Select Read / Write Configuration.
  Page 281
21. Select Before Replace ECU.
IMPORTANT:
Do not select Save (see Figure 12).
22. Write down or print the Setting Value (Multi-AV configuration) for each of the Items listed (see Figure 12).
NOTE:
^ The screen shown in Figure 12 is an example.
^ These setting values will be used during the reprogram (reconfigure) of the Multi AV later in this procedure.
23. When done, select Home.
Part 2: Perform Multi AV initialization using the vehicles on-board Systems Diagnostic Menu.
NOTE:
^ The ignition should still be ON.
  Page 282
^ Leave C-III plus turned ON with the home screen displayed and the VI connected while performing Multi-AV initialization.
1. Turn the audio system OFF.
2. Put the AV system into System Diagnostic Mode as follows:
a. Press and hold the SETTING button.
b. While holding the SETTING button, turn the volume control knob 40 clicks or more.
^ The volume control knob can be turned either direction.
^ When the system goes into the System Diagnostic Menu, the screen in Figure A2 will display.
3. Select Confirmation/Adjustment.
4. Select Initialize Settings.
NOTE:
Use the scroll arrow to find "Initialize Settings".
5. Select Accessory Number Initialization.
  Page 283
6. Select Yes.
7. Select Yes.
8. The screen in Figure A7 will display while initializing.
9. The screen in Figure A8 will display when initializing is complete.
10. Reboot the Multi AV system as follows:
a. Turn the ignition OFF.
b. Wait 10 Seconds.
c. Turn the ignition ON.
Part 3: Using C-III plus; reprogram (reconfigure) the Multi AV unit and confirm the control unit part number has changed.
  Page 284
1. Select Re/programming Configuration.
2. Check the box confirming the precautions have been read then select Next.
3. Use Manual Selection (Vehicle Name), then select correct Make, Model and Year.
NOTE:
If the screen in Figure B3 does not display, skip to step 5.
4. Click on Select.
  Page 285
5. Confirm correct VIN, Vehicle Name, and Model Year.
6. Select Confirm.
7. After system call completes, select MULTI AV.
8. Select Manual Configuration.
9. Use the drop down arrows to select the values for each item listed (see Figure B7).
^ For MICROPHONE, select "DIRECTIONAL MID".
^ For all other items, use the values that you wrote down in Part 1, step 22.
  Page 286
10. Select Next.
11. Confirm correct values for items listed and then select OK.
12. Wait for C-III plus to transfer the reprogramming (reconfiguration) to Multi AV - about 1 minute or less.
13. After C-III plus finishes transferring the reconfiguration to the MULTI AV, select Home.
14. Turn the ignition OFF and wait 10 seconds.
15. Start the engine and let it idle while the Multi AV system reboots.
16. Use C-III plus to clear any codes from the Multi AV system:
a. Select Diagnoses (One System) > Multi AV > Self Diagnosis Results.
b. Clear any codes that are present.
  Page 287
17. Confirm the Multi AV part number has changed:
a. Select ECU Identification.
b. Compare the part number you wrote down in Part 1, step 11, on page 5 to the one that is now displayed.
c. The part number should be different.
NOTE:
If the part numbers are not different, the reconfigure process was not successful.
18. Close the C-III plus and disconnect the VI from the vehicle.
Part 4: Make sure the Multi AV system is operational.
1. Confirm that fan, temperature, and air flow modes can be adjusted.
2. Turn the radio ON.
3. Turn the volume knob and make sure the audio volume responds to movement of the knob.
Part 5: Replace the system microphone
^ Refer to the AV section in the Service Manual for microphone replacement information.
CAUTION:
Be careful not to crease the headlining.
^ Make sure to use the new microphone listed in the Parts Information.
^ Make sure to use the new map lamp finisher listed in the Parts Information.
IMPORTANT:
Make sure the new microphone is firmly snapped into place. If the microphone is loose, it could pick up extra noise from an unintended
source.
Part 6: Check Microphone Operation Using the vehicles on-board Systems
Diagnostic Menu.
1. Turn the ignition ON and the audio system OFF.
  Page 288
2. Put the AV system into System Diagnostic Mode as follows:
a. Press and hold the SETTING button.
b. While holding the SETTING button, turn the volume control knob 40 clicks or more.
^ The volume control knob can be turned either direction.
^ When the system goes into the System Diagnostic Menu, the screen in Figure M2 will display.
3. Select Confirmation/Adjustment.
4. Select Hands-free Phone.
NOTE:
Use the scroll arrow to find Hands-free Phone.
  Page 289
5. Select Voice Microphone Test.
^ A "feedback noise will come from the system speakers as confirmation that the microphone is operating.
^ If you speak, you should hear your voice coming from the system speakers. This is further confirmation that the microphone is operating.
6. Reboot Multi AV system by cycling the ignition OFF for 10 seconds, then back ON.
7. Reset the customer's radio stations presets.
The Service Procedure is complete, but you may need to adjust the system for customer preference:
Adjust outgoing call volume to a level that is suitable for the customer's voice as follows:
A. Press the SETTING button on the control panel.
B. Select Volumes & Beeps.
C. Adjust the Outgoing Call volume to the customer's preference.
^ If extremely loud talker, set to level 1 (-).
^ If moderately loud talker, set to level 2.
^ If normal loud talker, set to level 3.
^ If moderately quiet talker, set to level 4.
^ If quiet talker, set to level 5 (+).
  Page 290
Disclaimer