Skip to main content

Nissan-Datsun 370Z Technical 11-005C Date: 130401 Navigation System - Map Data Update Index Classification:

 Nissan-Datsun 370Z Technical  11-005C Date: 130401
Navigation System - Map Data Update Index
Classification:
EL11-001c
Reference:
NTB11-005c
Date:
April 1, 2013
NAVIGATION MAP DATA UPDATE MATRIX
This bulletin has been amended. Information for 2012 vehicles has been added to the matrix. No other changes have been made. Please discard all
previous copies.
APPLIED VEHICLES:
2003-2012 Nissan vehicles equipped with Navigation system - except LEAF
SERVICE INFORMATION
Two methods are used to update/upgrade Navigation Map Data:
1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR
2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed.
Use the matrix to determine which method is utilized for each Applied Vehicle.
  Page 345
Disclaimer
Labels:
Location: 1267 Foster Cross Rd, Oneida, TN 37841, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more