Skip to main content

Nissan-Datsun 370Z Technical 12-106A Date: 121219 Cell Phone - Poor Hands Free Phone Sound Quality Classification:

Nissan-Datsun 370Z Technical  12-106A Date: 121219
Cell Phone - Poor Hands Free Phone Sound Quality
Classification:
EL12-079a
Reference:
NTB12-106a
Date:
December 19, 2012
HANDS-FREE PHONE POOR SOUND QUALITY
The Applied Vehicles and Parts Information in this bulletin have been amended. Please discard previous versions.
APPLIED VEHICLES:
  Page 291
APPLIED VINs and DATES
IF YOU CONFIRM
The customer has experienced or is experiencing, while using the hands-free phone, people on the other end of a phone call cannot hear them.
The customer's experience may include:
^ Voice is choppy or cuts-out.
^ Voice sounds distant.
^ Voice sounds as if speaking through a tunnel.
^ Voice sounds like it is under water.
ACTION
1. Replace the TEL Adaptor Unit.
  Page 292
2. Replace the microphone and the map lamp finisher.
^ For Juke, replace the microphone and microphone finisher.
IMPORTANT:
The purpose of ACTION is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service Procedure
as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the claims coding shown.
SERVICE PROCEDURE
1. Replace the TEL Adaptor Unit.
  Page 293
^ Refer to the AV section in the appropriate Service Manual for replacement information.
2. Replace the Microphone.
^ Refer to the AV section in the appropriate Service Manual for microphone replacement information.
CAUTION:
Be careful not to crease the headlining.
^ Make sure to use the new microphone listed in the Parts Information.
^ Make sure to use the new map lamp finisher listed in the Parts Information.
NOTE:
For Juke use a new microphone finisher with new fasteners listed in the Parts Information.
IMPORTANT:
Make sure the new microphone is firmly snapped into place. If the microphone is loose, it could pick up extra noise from an unintended
source.
Disclaimer
Labels:
Location: 2076 Big Sandy River Rd, Fort Gay, WV 25514, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more