Skip to main content

Nissan-Datsun 370Z Technical 09-020E Date: 130404 Emissions - EVAP System DTC Diagnosis Supplement Classification:

 Nissan-Datsun 370Z Technical  09-020E Date: 130404
Emissions - EVAP System DTC Diagnosis Supplement
Classification:
EC09-001e
Reference:
NTB09-020e
Date:
April 14, 2013
EVAP LEAK DTC DIAGNOSIS
This bulletin has been amended to the APPLIED VEHICLES section. Please discard all previous versions of this bulletin.
APPLIED VEHICLES:
2007 - 2014 Nissan vehicles SERVICE INFORMATION
  Page 337
  Page 338
  Page 339
  Page 340
If one or more DTCs listed below related to EVAP system leaks is found stored in Self Diagnosis, use the REPAIR FLOW CHART. Use the EVAP
system diagram for reference.
^ DTCs: P0442, P0455, and P0456
^ This Service Procedure can be used in addition to the procedure(s) outlined in the applicable Service Manual, and other bulletins applicable
to specific EVAP leak DTCs when necessary.
^ If a "Smoke (Leak Detection) Machine is available and preferred, the REPAIR FLOW CHART can still be used. This tool would be used in
place of watching for pressure drop and spraying with soapy water. Refer to the Machine's Operator's Manual for proper use.
CAUTION:
Use Essential Tool J-42909 (sent out to dealers September 1997) or equivalent to pressurize the EVAP system. Do Mot pressurize over the
amount specified in the applicable Service Manual. Do NOT use shop air pressure.
IMPORTANT NOTE:
If an EVAP system DTC(s) not related to EVAP leaks is/are found stored in Self Diagnosis, this bulletin does not apply. Refer to ASIST and
the appropriate Service Manual for diagnostic procedure(s) as needed.
  Page 341
  Page 342
CLAIMS INFORMATION
Disclaimer
Labels:
Location: Charter Oak Greenway, East Hartford, CT 06118, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more