Skip to main content

NTB09-091 SUNROOF WIND NOISE

SUNROOF WIND NOISE
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB09-091, Date of Issue: September 14, 2009
IF YOU CONFIRM
A wind noise is coming from the sunroof glass area.
l The noise can be isolated to the sunroof glass area if it stops after covering the
sunroof seal with 'painter's tape' or equivalent.
ACTION
Adjust the Sunroof Glass Lid Assembly ("center it" and "level it" in the sunroof
opening).
l Refer to the SERVICE PROCEDURE of this bulletin for repair instructions.
l For additional information, refer to the appropriate Electronic Service Manual
(ESM).
l Do not replace the glass lid assembly (lid) when adjustment can resolve the
incident, if it should occur.
CLAIMS INFORMATION
Submit a Primary Operation (PO) line claim using the following claims coding:
Sentra, Versa, Maxima
SENTRA, VERSA, MAXIMA CLAIMS INFORMATION
Altima
ALTIMA CLAIMS INFORMATION
NISSAN: 2007-2010 Altima, Sentra, Versa; 2009-2010 Maxima
CLASSIFICATION: BT09-018
APPLIED
VEHICLES:
Maxima (A35) with Single Panel Sunroof; Altima Sedan (L32); Altima
Coupe (CL32); Altima Hybrid (L32HV); Sentra (B16); Versa (C11X and
SC11X)
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE
PROCEDURE (starting on Page 2) as it contains information that is essential
to successfully completing this repair.
DESCRIPTION OP CODE SYM DIA FRT
Adjust Sun Roof BX1JAA ZL 53 0.2
DESCRIPTION OP CODE SYM DIA FRT
2009 Nissan Maxima S
SUNROOF WIND NOISE
2020年3月30日 12:41:40 Page 1 © 2011 Mitchell Repair Information 44 Company, LLC.
SERVICE PROCEDURE
ADJUST SUNROOF GLASS LID ASSEMBLY
1. Clean and inspect the Sunroof Glass Lid Assembly (glass lid) seal and sunroof
opening edge.
l Use isopropyl alcohol or suitable cleaner.
2. Adjust the glass lid as needed (refer to Fig. 1, and Fig. 2).
l Use the appropriate ESM as needed.
l The front of the glass lid should be flush but no more than 0.5 mm below the
roof surface.
l The rear of the glass lid should be flush but no more than 0.5 mm above the
roof surface.
l The difference in the glass lid's front-to-rear gaps should be no greater
than 1 mm.
Fig. 1: Adjusting Glass Lid (1 Of 2)
Fig. 2: Adjusting Glass Lid (2 Of 2)
Adjust Sun Roof BX1JAA ZL 53 0.3
2009 Nissan Maxima S
SUNROOF WIND NOISE
2020年3月30日 12:41:40 Page 2 © 2011 Mitchell Repair Information Company, LLC.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...