NTB09-092 2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY

2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB09-092a, Date of Issue: February 19, 2010
Superceded Bulletin(s): NTB09-092, Date of Issue: September 15, 2009
IF YOU CONFIRM
The driver's seat bottom very slightly "rocks" and/or "shifts" back and forth when
accelerating, braking, or when making a turn.
ACTION
Replace the driver seat frame (adjuster assembly) with a new one.
Fig. 1: Seat Frame (Adjuster Assembly)
PARTS INFORMATION
PARTS INFORMATION
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
CLAIMS INFORMATION
NISSAN: 2009-2010 Maxima
CLASSIFICATION: BT09-039a
APPLIED VEHICLES: 2009-2010 Maxima (A35)
APPLIED VIN: 2009 vehicles-All; 2010 vehicles built before 1 N4AA(****)AC 825954
APPLIED DATE: Vehicles built before December 2, 2009
NOTE: This bulletin has been amended. The Applied Vehicles section has been
revised. Please discard all previous copies of this bulletin.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire Service Procedure as
it contains information that is essential to successfully completing this
repair.
DESCRIPTION P/N QTY
Frame Assy - Front Seat
Cushion (Seat Adjuster Assy.)
Use the VIN and electronic parts catalog (FAST
or equivalent) to determine the correct P/N.
1
DESCRIPTION PFP OP CODE SYM DIA FRT
RPL Left Seat Cushion Frame Ass'y (1) VH32AA ZJ 46 (2)
(1) Refer to FAST or equivalent and use the Frame Assy.-Seat Cushion P/N as the
PFP.
2009 Nissan Maxima S
2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
2020年3月30日 12:51:45 Page 1 © 2011 Mitchell Repair Information 50 Company, LLC.
SERVICE PROCEDURE
1. Write down all radio station pre-sets.
RADIO STATION PRE-SETS
2. If equipped - write down/record the following customer settings for the ATC
(Automatic Temperature Control) system (refer to the ESM as needed):
l Temperature Setting Trimmer
l Foot Position Setting Trimmer
l Inlet Port Memory Function
3. Turn the ignition switch OFF.
4. Disconnect both battery cables - negative cable first.
5. WARNING:
6. Carefully remove the driver seat from the vehicle.
l Refer to section SE of the ESM for seat removal procedure.
7. Replace the seat frame/adjuster assembly.
l Refer to the ESM - SE Section, Front Seat Driver Side: Disassembly and
Assembly.
l Seatback Removal.
l Seat Outer Finisher Removal.
(2) Refer to the current Nissan Warranty Flat Rate Manual and use the indicated
FRT.
IMPORTANT: Follow all cautions, warnings, and notes in the Electronic Service Manual
(ESM) when working on or near a Supplemental Restraint System (SRS),
such as an air bag.
Presets 1 2 3 4 5 6
A
B
C
SAT
WARNING: Wait for at least 3 minutes before removing the driver seat:
CAUTION: Use covers as needed to protect interior surfaces from being
scratched or damaged.
NOTE: This bulletin contains additional helpful information for:
2009 Nissan Maxima S
2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
2020年3月30日 12:51:45 Page 2 © 2011 Mitchell Repair Information Company, LLC.
Fig. 2: Seat Frame (Adjuster Assembly)
8. Connect the battery cables - positive cable first.
9. Reset the clock and the radio station presets.
10. Refer to the Service Manual for the following "reset/relearn" procedures:
l Power Window Initialization
l Sunroof Memory Reset/Initialization
l ATC Temperature Setting Trimmer (A/C system)
l ATC Foot Position Setting Trimmer (A/C system)
l ATC Inlet Port Memory Function - FRE and REC (A/C system)
l Rear View Monitor Possible Route Line Center Position Adjustment (if
equipped)
l Steering Angle Sensor Neutral Position
11. Inform the customer they will need to "reset" their Automatic Drive Positioner.
SEATBACK FINISHER REMOVAL
1. Reach under the seat and disconnect the 2 elastic straps for the toe flap.
Fig. 4: Toe Flap
2. Insert your fingers behind the bottom corners of the finisher.
3. Pull the finisher to unsnap the bottom clips.
Fig. 5: Bottom Clips Location
4. Hold the finisher on the outboard side (side towards the door).
5. Pull the finisher to unsnap the outboard side hook.
Fig. 6: Outboard Side Hook Location
6. Hold the top of the finisher and push it down about 1 inch.
Fig. 7: Pushing Driver's Seat Bottom Shifts Down
7. Pull out on the outboard side of the finisher.
8. Reach behind the finisher.
NOTE: The seatback finisher is held on with:
l 2 top hooks
l 2 side hooks
l 2 bottom clips
Fig. 3: Seatback Finisher
2009 Nissan Maxima S
2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
2020年3月30日 12:51:46 Page 3 © 2011 Mitchell Repair Information Company, LLC.
Fig. 8: Side Hook Location
9. Unsnap the inboard side hook.
Fig. 9: Side Hook Detail
SEAT OUTER FINISHER REMOVAL
1. Carefully pull out on the center of the finisher.
2. At the rear of the finisher, insert a plastic trim tool in the gap.
3. Carefully pry between outer and inner finisher.
Fig. 10: Plastic Trim Tool
4. Continue to pull while pushing on each clip.
l See Fig. 12 on the next page for clip locations.
Fig. 11: Pushing Clip
5. With the rear of the finisher unclipped, carefully pull on the finisher to release
the 4 side clips.
l See Fig. 12 for side clip locations.
Fig. 12: Side Clip Location
6. To release the front clip:
a. Pull on the front edge of the finisher,
b. And pry between the finisher and the seat frame with a plastic trim tool.
Fig. 13: Front Edge of Finisher
NOTE: The front clip is released in step 6.
2009 Nissan Maxima S
2009-2010 MAXIMA; DRIVER'S SEAT BOTTOM SHIFTS SLIGHTLY
2020年3月30日 12:51:46 Page 4 © 2011 Mitchell Repair Information Company, LLC.