Skip to main content

NTB09-056 ACCESSORY WHEEL LOCKS INSTALLATION AND REMOVAL

ACCESSORY WHEEL LOCKS INSTALLATION AND REMOVAL
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB09-056, Date of Issue: July 14, 2009
SERVICE INFORMATION
Always use hand tools when installing or removing accessory wheel lock nuts.
Use of an impact wrench or other power tool may cause permanent damage to the wheel
lock nut and/or key.
CLAIMS INFORMATION
Accessory wheel locks, wheel lock keys, or vehicle wheels that are damaged due to
improper installation or removal will not be considered a manufacturer defect and will
not be covered under warranty.
Fig. 1: Damaged Key & Nut
Accessory Wheel Lock Installation / Removal Guidelines
l For ease of removal, the wheel lock nut should always be the first lug nut
removed.
l If needed, clean threads on lug studs with a wire brush.
l The wheel lock nut should always be the last lug nut tightened.
l Always use the special key supplied in the wheel lock set to install and remove
the wheel locks.
l Always tighten the wheel lock nuts - using a hand torque wrench - to the torque
specification in the Service Manual.
NISSAN: All Nissan
CLASSIFICATION: WT09-002
APPLIED VEHICLES: All Nissan
WARNING: Do not use power tools to install or remove accessory wheel lock nuts.
2009 Nissan Maxima S
ACCESSORY WHEEL LOCKS INSTALLATION AND REMOVAL
2020年3月30日 12:11:50 Page 1 © 2011 Mitchell Repair Information 54 Company, LLC.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more