NTB09-085 MAXIMA AND ALTIMA SEDAN AND COUPE; CUP HOLDER LID WILL NOT OPEN OR CLOSE

MAXIMA AND ALTIMA SEDAN AND COUPE; CUP HOLDER LID WILL NOT OPEN OR CLOSE
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB09-085a, Date of Issue: May 28, 2010
Superceded Bulletin(s): NTB09-085, Date of Issue: September 3, 2009
IF YOU CONFIRM
The cup holder lid (lid) will not open or close.
ACTION
Maxima shown; other models similar.
l For repair procedure, refer to the SERVICE PROCEDURE section of this bulletin.
Fig. 1: Cup Holder Lid, Maxima shown; other models similar.
CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
CLAIMS INFORMATION
NISSAN:
2009 - 2010 Maxima; 2007 - 2009 Altima Sedan; 2008 - 2010 Altima
Coupe
CLASSIFICATION: BT09-047a
APPLIED VEHICLES:
2009 - 2010 Maxima (A35); 2007 - 2009 Altima Sedan (L32) with M/T
ONLY; 2008 - 2010 Altima Coupe (CL32)
APPLIED VINS and
DATES:
2009 Maxima: Vehicles built after 1N4AA51E(*)9C 855418, and
06/16/09, 2010 Maxima-All, 2007 - 2009 Altima Sedan-All, 2008 - 2010
Altima Coupe-All
NOTE: This bulletin has been amended. The title, APPLIED VEHICLES, CLAIMS
INFORMATION, and the SERVICE PROCEDURE have been amended. Discard
previous copies of this bulletin.
NOTE: Do not replace the center console cup holder assembly for this
incident, if it should occur.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire Service Procedure as
it contains information that is essential to successfully completing this
repair.
DESCRIPTION PFP OP CODE SYM DIA FRT
Repair Cup Holder (1) VX2CAA ZE 32 0.2
(1) Refer to the electronic parts catalog (FAST or equivalent) and use the
2009 Nissan Maxima S
MAXIMA AND ALTIMA SEDAN AND COUPE; CUP HOLDER LID WILL NOT OPEN OR CLOSE
2020年3月30日 12:37:45 Page 1 © 2011 Mitchell Repair Information 50 Company, LLC.
SERVICE PROCEDURE
Fig. 2: Opening the Lid
1. Open the lid by pushing on its backside (see Fig. 2).
Fig. 3: Lid Hinge Pin & Arm
Fig. 4: Lid Hinge Pin & Arm
2. Align the hinge pin (pin) up to the opening at the end of the cup holder arm
(arm). See Fig. 3 and Fig. 4.
Fig. 5: Closed Lid
3. Close the lid (see Fig. 5).
l Push down on the lid enough for it to stay closed by itself.
l Make sure the arm and the pin stay aligned while closing (see Fig. 6).
Fig. 6: Pin & Arm
4. Push down on the end of the lid until the pin snaps into the arm (see Fig. 6).
Fig. 7: Inspecting Gap Between Pin & Lid
l After snapping in place, make sure there is no gap between the pin and lid
(see Fig. 7).
5. Verify repairs are complete by opening and closing the lid.
appropriate "Cup Holder Assembly" part number as the PFP.
NOTE: l Repairs are shown performed with the cup holder out of the vehicle.
l Repairs can be done with the cup holder in the vehicle.
l Repairs shown are performed on the rear of the lid. Repairs to the front
are similar.
l Maxima cup holder shown; Altima Sedan/Coupe cup holders similar.
l For Altima Sedan: Applies to M/T equipped models only .
CAUTION: Do not put any items in the cup holder that could keep the lid from
properly closing.
2009 Nissan Maxima S
MAXIMA AND ALTIMA SEDAN AND COUPE; CUP HOLDER LID WILL NOT OPEN OR CLOSE
2020年3月30日 12:37:46 Page 2 © 2011 Mitchell Repair Information Company, LLC.