Skip to main content

NTB09-077 2009-2010 MAXIMA SEAT BACK BOARD REMOVAL PROCEDURE

2009-2010 MAXIMA SEAT BACK BOARD REMOVAL PROCEDURE
TECHNICAL SERVICE BULLETIN
Reference Number(s): NTB09-077, Date of Issue: March 15, 2010
SERVICE INFORMATION
If the front seat back needs to be removed for any reason, use the Service Procedure in
this bulletin.
PARTS INFORMATION
PARTS INFORMATION
SERVICE PROCEDURE
1. Move/adjust the seat bottom and seat back to the full forward position.
2. Remove the seat back finisher as follows:
a. Reach under the seat and disconnect the 2 elastic straps for the toe flap.
Fig. 2: Toe Flap
b. Insert your fingers behind the bottom corners of the finisher.
NISSAN: 2009-2010 Maxima
CLASSIFICATION: BT09-043
APPLIED VEHICLES: 2009-2010 Maxima (A35)
DESCRIPTION PART# QUANTITY
Finisher (Back Board) Clips 87183-9N00B Up to 2 (If needed)
NOTE: l Use this procedure for the front driver or front passenger seat.
l The photos in this procedure are for the passenger seat. The driver seat
is the same.
CAUTION: Use covers as needed to protect interior surfaces from scratches or
damage.
NOTE: The seat back finisher is held on with:
l 2 top hooks
l 2 side hooks
l 2 bottom clips
l 2 elastic straps from toe flap.
Fig. 1: Seat Back Finisher
2009 Nissan Maxima S
2009-2010 MAXIMA SEAT BACK BOARD REMOVAL PROCEDURE
2020年3月30日 12:18:28 Page 1 © 2011 Mitchell Repair Information 32 Company, LLC.
c. Pull the finisher to unsnap the bottom clip.
Fig. 3: Bottom Clips Location
d. Hold the finisher on the outboard side (side towards the door).
l For the passenger seat, the outboard side is to the right.
l For the driver seat, the outboard side is to the left.
e. Pull the finisher to unsnap the outboard side hook.
Fig. 4: Outboard Side Hook Location
f. Hold the top of the finisher and push it down about 1 inch.
Fig. 5: Pushing Seat Back Board Down
g. Pull out on the outboard side of the finisher.
h. Reach behind the finisher.
Fig. 6: Side Hook Location
i. Unsnap the inboard side hook.
Fig. 7: Side Hook Detail
2009 Nissan Maxima S
2009-2010 MAXIMA SEAT BACK BOARD REMOVAL PROCEDURE
2020年3月30日 12:18:29 Page 2 © 2011 Mitchell Repair Information Company, LLC.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more