Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 10-110 Date: 100915

2014 Nissan-Datsun Altima Diagrams. DTC # 10-110 Date: 100915



Brakes - Low Fluid Level Warning Diagnostics



Classification: BR10-010



Reference: NTB10-110



Date: September 15, 2010



ALTIMA AND MAXIMA; LOW BRAKE FLUID WARNING LIGHT "ON" DIAGNOSTIC PROCEDURE



APPLIED VEHICLES:



2007-2011 Altima Coupe, Hybrid, Sedan (C/L32/HV)



2009-2011 Maxima (A35)



SERVICE INFORMATION



It is possible for brake pad wear to cause the fluid level in the master cylinder reservoir to decrease to the MIN level, turning "ON" the Low Brake



Fluid Warning Light.



If you confirm that the warning light is illuminated, perform the following procedures to inspect the vehicle and determine the proper repair method.



WARRANTY NOTE:



A low fluid level in the master cylinder reservoir due only to brake pad wear not caused by any defect is not warrantable.



INSPECTION



Use a scale to check the thickness of the front brake pads.



^ View the brake pads though the caliper body inspection hole.



1. If the remaining brake pad lining thickness is as shown above.



AND



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 445



The brake fluid level in the master cylinder fluid reservoir is at or near the MIN level line,



The drop in the brake fluid level is likely due to brake pad wear not caused by any defect.



ACTION: Add brake fluid to the reservoir.



2. If the remaining brake pad lining thickness is as shown above.



AND



The brake fluid level in the master cylinder fluid reservoir is at or below the MIN level line,



ACTION: Perform brake system inspections in accordance with the Electronic Service Manual (ESM) to determine the cause of the brake fluid



level decrease.



3. To determine if the front brake pads should be replaced, refer to the applicable ESM for front brake pad wear limit thickness information.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...