Skip to main content

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 119

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 119
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
- GO TO 2
2. STEP 2
Check "Self diagnostic result" with CONSULT-III.
Is the DTC detected?
YES - Perform diagnosis procedure. See: B2115.
NO - Inspection End.
NOTE:
First perform diagnosis for B2126 if B2126 is detected. See: B2126.
Diagnosis Procedure
1. PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check "Self diagnostic result" with CONSULT-III.
3. Erase the DTC.
4. Perform DTC confirmation procedure. See: B2115.
Is the DTC displayed again?
YES - GO TO 2
NO - Check intermittent incident. See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Intermittent Incident.
2. CHECK COMPONENTS
See: Accessories and Optional Equipment/Memory Positioning Systems/Testing and Inspection/Component Tests and General
Diagnostics/Lifting Sensor/Rear/Component Function Check and See: Accessories and Optional Equipment/Memory Positioning Systems/Testing
and Inspection/Component Tests and General Diagnostics/Lifting Motor/Rear/Component Function Check.
- Inspection End.
B2117
B2117 ADJ PEDAL MOTOR
Description
- The pedal adjusting sensor is installed to pedal adjusting motor assembly.
- The resistance of pedal adjusting sensor is changed according to the forward/backward position of pedal assembly.
- The terminal voltage of automatic drive positioner control unit will be changed according to a change of pedal adjusting sensor resistance.
Automatic drive positioner control unit calculates the pedal position from the voltage.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. STEP 1
Turn ignition switch ON.
- GO TO 2
2. STEP 2
Check "Self diagnostic result" with CONSULT-III.
Is the DTC detected?
YES - Perform diagnosis procedure. See: B2117.
NO - Inspection End.
Diagnosis Procedure
Regarding Wiring Diagram information, See: Accessories and Optional Equipment/Memory Positioning Systems/Diagrams/Electrical
Labels:
Location: 1494-1614 50th St NW, Montevideo, MN 56265, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more