Skip to main content

Nissan Armada Technical Service Bulletin # 10-078 Date: 100621

****************************
****************************

Nissan Armada Technical Service Bulletin # 10-078 Date: 100621
Engine Controls - ECM Programming Interruption Recovery
Classification: EC10-015
Reference: NTB10-078
Date: June 21, 2010
Nissan Armada 2wd v8 5.6L Parts Service 163
REPROGRAM INTERRUPTION RECOVERY PROCEDURE
SERVICE INFORMATION
A complete step-by-step General Procedure for CONSULT-III (C-III) ECM Reprogram Interruption Recovery is now available by attachment in this
bulletin.
While performing ECM (Engine Control Module) reprogramming, the reprogramming may stop (become interrupted) before it is 100% complete.
One of two messages may appear:
^ The VI probe is disconnected on USB, please check the connection of the probe.
^ Reprogramming fail, "Error code 0".
In many cases, reprogramming recovery is possible and the ECM may not need to be replaced if the complete ECM part number has been registered
into the ECM before reprogramming stopped.
NOTE:
ECM is referred to as ECU in C-III.
The ECM Reprogram Interruption Recovery General Procedure applies to Technical Service Bulletins that include ECM reprogramming published
in April 2010 and later.
IMPORTANT: BEFORE STARTING REPROGRAMMING
^ Connect a battery charger to the vehicle battery.
^ Be sure to turn OFF all vehicle electrical loads.
^ For ECM reprogramming, the C-III MUST be connected to the VI using the USB cable.
^ Be sure to connect the AC Adapter.
Nissan Armada 2wd v8 5.6L Parts Service 164
Nissan Armada 2wd v8 5.6L Parts Service 165
Nissan Armada 2wd v8 5.6L Parts Service 166
Nissan Armada 2wd v8 5.6L Parts Service 167
Nissan Armada 2wd v8 5.6L Parts Service 168
Nissan Armada 2wd v8 5.6L Parts Service 169
Nissan Armada 2wd v8 5.6L Parts Service 170
Nissan Armada 2wd v8 5.6L Parts Service 171
Nissan Armada 2wd v8 5.6L Parts Service 172
Nissan Armada 2wd v8 5.6L Parts Service 173
Nissan Armada 2wd v8 5.6L Parts Service 174
Nissan Armada 2wd v8 5.6L Parts Service 175
Nissan Armada 2wd v8 5.6L Parts Service 176
Nissan Armada 2wd v8 5.6L Parts Service 177
Attachment General Procedure
Labels:
Location: Bringolf Ranch Rd, Riverton, WY 82501, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more