Skip to main content

B1195 Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 103

****************************
****************************

- END
B1195
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 103
B1193 - B1196 SIDE CURTAIN AIR BAG MODULE RH (FRONT)
Description
DTC B1193 - B1196 RH SIDE CURTAIN AIR BAG MODULE (FRONT)
The RH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens
and shorts in detected lines to the RH side curtain air bag module (front).
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.INSPECTION START
Turn ignition switch ON.
- GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-III.
Is the DTC detected?
YES - See: B1193.
NO - Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
- GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
- GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
- GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 6
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 104
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Diagnosis Sensor Unit/Trouble Diagnosis Without CONSULT-III.
- END
Labels:
Location: Cuyuni-Mazaruni, Guyana

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more