Skip to main content

Nissan Armada Technical Service Bulletin # 13-015 Date: 130215

****************************
****************************Nissan Armada Technical Service Bulletin # 13-015 Date: 130215
Keyless Systems - MIL ON, DTC B2190 Set
Classification:
EL13-004
Reference:
NTB13-015
Date:
February 15, 2013
MIL ON WITH DTC B2190
APPLIED VEHICLES:
All Nissan equipped with a Key-Slot for an Intelligent Key
SERVICE INFORMATION
DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons:
1. Something other than an Intelligent Key is inserted into the Key-Slot.
Nissan Armada 2wd v8 5.6L Parts Service 357
2. An Intelligent Key issue.
3. A wiring issue between the Key-Slot and the BCM.
4. A Key-Slot issue.
If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the
Key-Slot.
For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure.
Service Manual DTC CONFIRMATION PROCEDURE for DTC B2190
Disclaimer
Labels:
Location: Nf-119, Young, AZ 85554, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more