Skip to main content

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-085A Date: 100528

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 09-085A Date: 100528



Interior - Cup Holder Lid Won't Open Or Close



Classification: BT09-047A



Reference: NTB09-085A



Date: May 28, 2010



MAXIMA AND ALTIMA SEDAN AND COUPE; CUP HOLDER LID WILL NOT OPEN OR CLOSE



This bulletin has been amended. The title, APPLIED VEHICLES, CLAIMS INFORMATION, and the SERVICE PROCEDURE have been



amended. Discard previous copies of this bulletin.



APPLIED VEHICLES:



2009 - 2010 Maxima (A35)



2007 - 2009 Altima Sedan (L32) with M/T ONLY



2008 - 2010 Altima Coupe (CL32)



APPLIED VINS and DATES:



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 441



2009 Maxima: Vehicles built after 1N4AA51E(*)9C 855418, and 06/16/09



2010 Maxima-All



2007 - 2009 Altima Sedan-All



2008 - 2010 Altima Coupe-All



IF YOU CONFIRM:



The cup holder lid (lid) will not open or close.



ACTION:



Reattach the lid hinge.



^ For repair procedure, refer to the SERVICE PROCEDURE section of this bulletin.



NOTE



Do not replace the center console cup holder assembly for this incident, if it should occur.



IMPORTANT:



The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service



Procedure as it contains information that is essential to successfully completing this repair.



CLAIMS INFORMATION



SERVICE PROCEDURE



NOTE:



^ Repairs are shown performed with the cup holder out of the vehicle.



^ Repairs can be done with the cup holder in the vehicle.



^ Repairs shown are performed on the rear of the lid. Repairs to the front are similar.



^ Maxima cup holder shown; Altima Sedan/Coupe cup holders similar.



^ For Altima Sedan: Applies to M/T equipped models only.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 442



1. Open the lid by pushing on its backside (see Figure 1).



2. Align the hinge pin (pin) up to the opening at the end of the cup holder arm (arm). See Figure 2 and 3.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 443



3. Close the lid (see Figure 4).



^ Push down on the lid enough for it to stay closed by itself.



^ Make sure the arm and the pin stay aligned while closing (see Figure 5).



4. Push down on the end of the lid until the pin snaps into the arm (see Figure 5).



^ After snapping in place, make sure there is no gap between the pin and lid (see Figure 6).



5. Verify repairs are complete by opening and closing the lid.airs are complete by opening and closing the lid.



CAUTION:



Do not put any items in the cup holder that could keep the lid from properly closing.



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 444

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more