Skip to main content

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 03-015B Date: 091221

2019 Nissan-Datsun Altima Diagnostic and Repair Information # 03-015B Date: 091221



M/T - Warranty Repair Fluid Requirements



Classification: MT02-001B



Reference: NTB03-015B



Date: December 21, 21009



2001-2010 NISSAN; MANUAL TRANSMISSION OIL REQUIRED FOR WARRANTY REPAIRS



This bulletin has been amended. Please discard all copies of the earlier version.



APPLIED VEHICLES: 2001-2010 Nissan Manual Transmission-Equipped Vehicles



SERVICE INFORMATION



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 393



If an Applied Vehicle equipped with Manual Transmission (MT) needs servicing for warranty repairs, Nissan Manual Transmission Fluid (MTF)



HQ Multi 75W-85, Nissan TransElf NFJ 75W-80, or Nissan GTR R35 Special is required. See the chart above.



IMPORTANT NOTE:



Nissan Manual Transmission Fluid (MTF) HQ Multi 75W-85, Nissan TransElf NFJ 75W-80, or Nissan GTR R35 Special oil must be used when



performing manual transmission repairs paid by Nissan. These include warranty, service contract, or goodwill repairs.



Nissan will not reimburse dealers for manual transmission repairs when Nissan Manual Transmission Fluid (MTF) HQ Multi 75W-85, Nissan



TransElf NFJ 75W-80, or Nissan GTR R35 Special oil is not used.



Nissan recommends use of the above listed manual transmission fluids, which optimize shift quality, for customer pay use as well.



Nissan Manual Transmission Fluid and all Nissan chemicals are ordered through the Direct Ship Chemical Care Product Program.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

C1142 C1142 PRESS SENSOR

**************************** **************************** C1142 C1142 PRESS SENSOR Description The front and rear pressure sensors convert the brake fluid pressure to an electric signal and transmit it to the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1142. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. FRONT PRESSURE SENSOR 1.CONNECTOR INSPECTION 1. Turn the ignition switch OFF. 2. Disconnect the front pressure sensor connector and ABS actuator and electric unit (control unit) connector and inspect the terminals for deformation, disconnection, looseness, or damage. Is the inspection result normal? YE
Post a Comment
Read more