Skip to main content

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-019A Date: 120827

2017 Nissan-Datsun Altima Technical Service Bulletin # 09-019A Date: 120827



Wipers/Washers - Intermittent Wiper Operation Information



Classification: EL09-010A



Reference: NTB09-019A



Date: August 27, 2012



INTERMITTENT WIPER OPERATION



This bulletin has been amended to apply to all vehicles with Intermittent Rain Sensing Wipers.



APPLIED VEHICLE: Nissan vehicles with Intermittent Rain Sensing Wipers



SERVICE INFORMATION



Vehicle may be equipped with the Rain-Sensing Auto Wiper system.



With this system:



2017 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 87



> A rain sensor is located on the windshield, if equipped.



> When the wiper lever is pushed down to the intermittent (INT) position, the wipers will operate when the rain sensor detects rain.



> May only make a single stroke unless rain is detected directly above the sensor.



> May also be identified by the word "AUTO ADJ" on the wiper switch (some models).



NOTE:



The wipers may operate unexpectedly when dirt, fingerprints, oil film, or insects are located on or around the sensor, or when exhaust gas or



moisture affect the rain sensor.



If a customer states the wipers do not work when the wiper lever is pushed down to the intermittent (INT) position, make sure the customer is



familiar with the above information.



^ You can demonstrate the operation of the system by pushing the wiper lever down to the intermittent (INT) position and spraying/sprinkling water



over the rain sensor.



NOTE:



If a wiper-operation incident does occur, refer to the applicable Electronic Service Manual (ESM) for further diagnostic assistance.

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more