Skip to main content

2014 Nissan-Datsun Altima Diagrams. DTC # 10-139 Date: 101123

2014 Nissan-Datsun Altima Diagrams. DTC # 10-139 Date: 101123



Electrical - Engine No Crank/No Start



Classification: EL10-030



Reference: NTB10-139



Date: November 23, 2010



ALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START



APPLIED VEHICLES2007 - 2010 Altima Sedan (L32) with CVT only



2008 - 2010 Altima Coupe (CL32) with CVT only



2007 - 2010 Altima Hybrid (L32HV)



IF YOU CONFIRM:



The engine will not crank (or go to READY MODE - Hybrid) when pressing the push-button ignition switch and applying the brake pedal.



ACCESSORY and IGNITION ON modes can be turned on and off during this condition.



ACTION:



Install a new brake lamp switch and sub-harness with those listed in PARTS INFORMATION.



For parts replacement and installation, refer to SERVICE PROCEDURE.



NOTE:



^ This bulletin does not apply to manual transmission equipped vehicles.



^ This bulletin does not apply to Hybrid vehicles with HEV related CONSULT-III DTCs.



^ This bulletin does not apply for this incident, should it occur, if ACCESSORY and IGNITION ON modes cannot be turned on.



> Go back to ASIST and the Electronic Service Manual (ESM) for further diagnostic and repair information.



IMPORTANT:



The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE



PROCEDURE as it contains information that is essential to successfully completing this repair.



PARTS INFORMATION



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 238



CLAIMS INFORMATION



STOP LAMP SUB-HARNESS



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 239



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 240



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 241



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 242



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 243



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 244



2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 245

Labels:

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more