Skip to main content

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 109 B1198 - B1201 SIDE CURTAIN AIR BAG MODULE LH (FRONT) Description DTC B1198 - B1201 LH SIDE CURTAIN AIR BAG MODULE (FRONT) The LH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the LH side curtain air bag module (front). PART LOCATION See: Restraints and Safety Systems/Air Bag Systems/Locations. DTC Logic DTC DETECTION LOGIC With CONSULT-III Without CONSULT-III DTC CONFIRMATION PROCEDURE (With CONSULT-III) 1.INSPECTION START Turn ignition switch ON. - GO TO 2. 2.CHECK SELF-DIAG RESULT Check for the DTC on CONSULT-III. Is the DTC detected? YES - See: B1198. NO - Inspection End. DTC CONFIRMATION PROCEDURE (Without CONSULT-III) NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. 1.IGNITION SWITCH Turn ignition switch ON. - GO TO 2 2.IGNITION SWITCH After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second. - GO TO 3 3.WAIT TIME Wait more than 3 seconds. - GO TO 4 4.REPEAT STEPS Repeat steps 1 to 3 twice. - GO TO 5 5.IGNITION SWITCH Turn ignition switch ON. - GO TO 6

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 109
B1198 - B1201 SIDE CURTAIN AIR BAG MODULE LH (FRONT)
Description
DTC B1198 - B1201 LH SIDE CURTAIN AIR BAG MODULE (FRONT)
The LH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens
and shorts in detected lines to the LH side curtain air bag module (front).
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.INSPECTION START
Turn ignition switch ON.
- GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-III.
Is the DTC detected?
YES - See: B1198.
NO - Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
- GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
- GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
- GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 6
Labels:
Location: São Gabriel da Cachoeira - State of Amazonas, 69750-000, Brazil

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more