Skip to main content

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 60

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 60
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
- GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
- GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
- GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
- GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. See: Restraints and Safety Systems/Air Bag Systems/Testing and
Inspection/Scan Tool Testing and Procedures/Diagnosis Sensor Unit/Trouble Diagnosis Without CONSULT-III.
- END
Diagnosis Procedure (Component Diagnosis)
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES - Replace the harness.
NO - GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES - Replace the harness.
NO - GO TO 3
3.RH SIDE AIR BAG SATELLITE SENSOR
Replace the RH side air bag satellite sensor. See: Restraints and Safety Systems/Air Bag Systems/Impact Sensor/Service and Repair/Side Air Bag
(Satellite) Sensor.
- GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. See: Relays and Modules/Relays and Modules - Restraints and Safety Systems/Air Bag Control
Module/Service and Repair.
- GO TO 5
5.RELATED HARNESS
Replace the related harness.
- END
B1118
B1118 - B1120 SATELLITE SENSOR LH
Description
DTC B1118 - B1120 SATELLITE SENSOR LH
The satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the satellite sensor LH for
internal failures and it's circuits for communication errors.
PART LOCATION
See: Restraints and Safety Systems/Air Bag Systems/Locations.
DTC Logic
DTC DETECTION LOGIC
With CONSULT-III
Without CONSULT-III
Labels:
Location: Unnamed Road, Slave Lake, AB T0G, Canada

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more