****************************
****************************
C1708
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 83
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1709
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 84
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1710
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 85
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1711
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 86
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 87
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1712
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 88
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1713
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 89
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1714
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 90
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1715
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 91
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1716
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 92
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1717
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 93
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1718
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 94
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1719
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 95
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1720
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 96
C1721
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1722
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 97
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1723
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 98
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1724
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 99
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1725
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 100
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1726
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 101
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1727
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 102
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1729
C1729 VEHICLE SPEED SIGNAL
Description
The vehicle speed signal is not being detected by the BCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On "SELECT DIAG MODE", select the "SELF-DIAG RESULT" screen.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 103
2. Check display contents on "SELF DIAG RESULT" screen.
Is the "CAN COMM CIRCUIT" displayed in the self-diagnosis display?
YES - See: C1729.
NO - Inspection End.
Diagnosis Procedure
MALFUNCTION CODE NO. 52 (DTC C1729)
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On "SELECT DIAG MODE", select the "SELF-DIAG RESULT" screen.
2. Check display contents on "SELF DIAG RESULT" screen.
Is the "CAN COMM CIRCUIT" displayed in the self-diagnosis display?
YES - Perform trouble diagnosis for CAN communication system. See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview/CAN Fundamental/Trouble Diagnosis Flow Chart.
NO - Check combination meter. See: Instrument Panel, Gauges and Warning Indicators/Testing and Inspection/Scan Tool Testing and
Procedures/CONSULT-III Function.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1735
C1735 IGNITION SIGNAL
Description
The BCM monitors the IGN ON signal on the CAN line and compares it to it's direct IGN ON signal. When these two signals do not match, the
BCM sets C1735.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On SELECT DIAG MODE, select the SELF-DIAG RESULT screen.
2. Check display contents on SELF DIAG RESULT screen.
Is C1735 displayed in the self-diagnosis display?
YES - See: C1735.
NO - Inspection End.
Diagnosis Procedure
MALFUNCTION CODE NO. 54 (DTC C1735)
1.CAN IGNITION SIGNAL
Check BCM IGN RLY signal with CONSULT-III. See: Body and Frame/Body Control Systems/Testing and Inspection/Pinout Values and
Diagnostic Parameters/Reference Value.
Are the inspection results normal with the ignition switch ON?
YES - GO TO 2.
NO - Check CAN system. See: Powertrain Management/Computers and Control Systems/Information Bus/Application and ID/CAN System
Specification Chart.
2.BCM POWER SUPPLY
Check BCM power supply (ignition ON). See: Body and Frame/Body Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Power Supply And Ground Circuit.
Is the power supply with the ignition switch ON normal?
YES - GO TO 3.
NO - Repair power supply as necessary.
3.DRIVE VEHICLE
Clear DTC and then test drive the vehicle and check the low tire pressure warning lamp.
Does the vehicle operate without any low tire pressure warning lamp?
YES - Inspection End.
NO - Replace BCM. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 104
C1801
C1801 VEHICLE HEIGHT SENSOR
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor. Depending on vehicle height, the height sensor signal should have between 0.2V and 4.8V.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK HEIGHT SENSOR OPERATION
CONSULT-III
1. Turn ignition switch ON
2. Select "HEIGT SEN" of AIR LEVELIZER data monitor test item.
HEIGHT SEN : 0.2V - 4.8V
Is the HEIGHT SEN voltage within the given range?
YES - Height sensor is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Height Sensor Signal Circuit/Diagnosis Procedure.
C1802
C1802 COMPRESSOR RELAY
Description
The compressor motor relay is controlled by the suspension control unit. The suspension control unit supplies voltage to the coil side of the relay
to activate it. The compressor motor relay, when activated, supplies power to the suspension air compressor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 105
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
C1803
C1803 EXHAUST SOLENOID
Description
The exhaust valve solenoid controls the vent function of the suspension control system. The exhaust valve solenoid is built into the suspension air
compressor. The suspension control unit supplies voltage to the exhaust valve solenoid to activate it.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK EXHAUST SOLENOID OPERATION
CAUTION:
While operating this active test, the suspension control system will vent air pressure and the vehicle ride height will lower. Ensure the
area around the vehicle is free from obstructions before beginning test.
CONSULT-III
1. Ensure the suspension control system has air pressure and is not drooping in the rear.
2. Select "EXHAUST SOLENOID" of AIR LEVELIZER active test items.
3. While operating test item, check that the exhaust valve solenoid opens to vent air from the system. The vehicle should lower when the exhaust
valve solenoid is activated.
Does the system vent properly?
YES - Exhaust valve solenoid is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Exhaust Valve Solenoid Circuit/Diagnosis Procedure.
C1804
C1804 HEIGHT ADJUSTING MALFUNCTION (COMPRESSOR)
Description
The compressor motor relay is controlled by the suspension control unit. The suspension control unit supplies voltage to the coil side of the relay
to activate it. The compressor motor relay, when activated, supplies power to the suspension air compressor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 106
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
C1805
C1805 HEIGHT ADJUSTING MALFUNCTION (EXH SOLENOID)
Description
The exhaust valve solenoid controls the vent function of the suspension control system. The exhaust valve solenoid is built into the suspension air
compressor. The suspension control unit supplies voltage to the exhaust valve solenoid to activate it.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK EXHAUST SOLENOID OPERATION
CAUTION:
While operating this active test, the suspension control system will vent air pressure and the vehicle ride height will lower. Ensure the
area around the vehicle is free from obstructions before beginning test.
CONSULT-III
1. Ensure the suspension control system has air pressure and is not drooping in the rear.
2. Select "EXHAUST SOLENOID" of AIR LEVELIZER active test items.
3. While operating test item, check that the exhaust valve solenoid opens to vent air from the system. The vehicle should lower when the exhaust
valve solenoid is activated.
Does the system vent properly?
YES - Exhaust valve solenoid is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Exhaust Valve Solenoid Circuit/Diagnosis Procedure.
C1806
C1806 VEHICLE HEIGHT SENSOR LOCKING MALFUNCTION
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK HEIGHT SENSOR OPERATION
CONSULT-III
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 107
1. Turn ignition switch ON
2. Select "HEIGT SEN" of AIR LEVELIZER data monitor test item.
HEIGHT SEN : 0.2V - 4.8V with no more than ±0.02V variation
Is the HEIGHT SEN voltage within the given range?
YES - Height sensor is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Height Sensor Signal Circuit/Diagnosis Procedure.
C1807
C1807 SENSOR 5V MALFUNCTION
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
Regarding Wiring Diagram information, See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic
)/Diagrams/Electrical Diagrams.
1.POWER SUPPLY CIRCUIT CHECK
1. Disconnect height sensor connector C8.
2. Turn the ignition switch ON.
3. Check voltage between the height sensor connector C8 terminal
1 and ground.
Is 5V present?
YES - System is working normally.
NO - Check harness or connector for open or short. If OK, replace the suspension control unit. See: Relays and Modules/Relays and Modules -
Steering and Suspension/Relays and Modules - Suspension/Suspension Control Module/Service and Repair/Removal and Replacement.
C1808
C1808 INTEGRAL TIME MALFUNCTION SUPPLYING AIR
Description
The suspension air compressor is supplied power by the compressor motor relay. The suspension control unit supplies power to the compressor
motor relay in order to activate the relay and subsequently activate the suspension air compressor.
DTC Logic
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 108
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
****************************
C1708
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 83
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1709
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 84
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1710
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 85
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1711
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 86
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1708 - C1711 DATA FROM TRANSMITTER NOT BEING RECEIVED
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 87
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1708.
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa?
YES - GO TO 2
NO - GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connection.
Is tire pressure receiver connector damaged or loose?
YES - Repair or replace tire pressure receiver connector.
NO - Replace BCM, then GO TO 3. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
Is there a tire that cannot register ID?
YES - Replace malfunctioning transmitter, then GO TO 5. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire
Pressure Sensor/Service and Repair.
NO - GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1712
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 88
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1713
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 89
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1714
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 90
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1715
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 91
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1716
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 92
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1717
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 93
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1718
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 94
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1719
C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1716.
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. See: Maintenance/Wheels and Tires/Tires/Specifications.
Are there any tires with pressure of 64 psi or more?
YES - Adjust tire pressure to specified value.
NO - GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does "DATA MONITOR ITEM" display 64 psi or more?
YES - Replace transmitter. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and
Repair. GO TO 3.
NO - GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 95
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1720
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 96
C1721
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1722
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 97
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1723
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 98
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1724
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 99
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1725
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 100
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1726
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 101
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1727
C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 102
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - See: C1712.
Diagnosis Procedure
MALFUNCTION CODE NO. 31, 32, 33, 34, 41, 42, 43, 44, 45, 46, 47 OR 48 (DTC C1712, C1713, C1714, C1715, C1720, C1721, C2722,
C1723, C1724, C1725, C1726 OR C1727)
1.PERFORM ID REGISTRATION
1. Carry out ID registration of all transmitters. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and
Inspection/Programming and Relearning/ID Registration Procedure.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
- GO TO 2
2.REPLACE TRANSMITTER
1. Check low tire pressure warning lamp again for flashing, replace malfunctioning transmitter. See: Instrument Panel, Gauges and Warning
Indicators/Tire Monitoring System/Tire Pressure Sensor/Service and Repair.
2. Carry out ID registration of all transmitters.
Can ID registration of all transmitters be completed?
YES - GO TO 3
NO - GO TO See: C1708.
3.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
2. Check all tire pressures with CONSULT-III within 5 minutes.
Does "DATA MONITOR ITEM" display tire pressure as normal without any warning lamp?
YES - Inspection End.
NO - Replace malfunctioning transmitter, and perform Step 3 again.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1729
C1729 VEHICLE SPEED SIGNAL
Description
The vehicle speed signal is not being detected by the BCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On "SELECT DIAG MODE", select the "SELF-DIAG RESULT" screen.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 103
2. Check display contents on "SELF DIAG RESULT" screen.
Is the "CAN COMM CIRCUIT" displayed in the self-diagnosis display?
YES - See: C1729.
NO - Inspection End.
Diagnosis Procedure
MALFUNCTION CODE NO. 52 (DTC C1729)
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On "SELECT DIAG MODE", select the "SELF-DIAG RESULT" screen.
2. Check display contents on "SELF DIAG RESULT" screen.
Is the "CAN COMM CIRCUIT" displayed in the self-diagnosis display?
YES - Perform trouble diagnosis for CAN communication system. See: Powertrain Management/Computers and Control Systems/Information
Bus/Testing and Inspection/Initial Inspection and Diagnostic Overview/CAN Fundamental/Trouble Diagnosis Flow Chart.
NO - Check combination meter. See: Instrument Panel, Gauges and Warning Indicators/Testing and Inspection/Scan Tool Testing and
Procedures/CONSULT-III Function.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
C1735
C1735 IGNITION SIGNAL
Description
The BCM monitors the IGN ON signal on the CAN line and compares it to it's direct IGN ON signal. When these two signals do not match, the
BCM sets C1735.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On SELECT DIAG MODE, select the SELF-DIAG RESULT screen.
2. Check display contents on SELF DIAG RESULT screen.
Is C1735 displayed in the self-diagnosis display?
YES - See: C1735.
NO - Inspection End.
Diagnosis Procedure
MALFUNCTION CODE NO. 54 (DTC C1735)
1.CAN IGNITION SIGNAL
Check BCM IGN RLY signal with CONSULT-III. See: Body and Frame/Body Control Systems/Testing and Inspection/Pinout Values and
Diagnostic Parameters/Reference Value.
Are the inspection results normal with the ignition switch ON?
YES - GO TO 2.
NO - Check CAN system. See: Powertrain Management/Computers and Control Systems/Information Bus/Application and ID/CAN System
Specification Chart.
2.BCM POWER SUPPLY
Check BCM power supply (ignition ON). See: Body and Frame/Body Control Systems/Testing and Inspection/Component Tests and General
Diagnostics/Power Supply And Ground Circuit.
Is the power supply with the ignition switch ON normal?
YES - GO TO 3.
NO - Repair power supply as necessary.
3.DRIVE VEHICLE
Clear DTC and then test drive the vehicle and check the low tire pressure warning lamp.
Does the vehicle operate without any low tire pressure warning lamp?
YES - Inspection End.
NO - Replace BCM. See: Body and Frame/Body Control Systems/Body Control Module/Service and Repair.
Special Repair Requirement
Perform preliminary check. See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Testing and Inspection/Initial
Inspection and Diagnostic Overview/Preliminary Check.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 104
C1801
C1801 VEHICLE HEIGHT SENSOR
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor. Depending on vehicle height, the height sensor signal should have between 0.2V and 4.8V.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK HEIGHT SENSOR OPERATION
CONSULT-III
1. Turn ignition switch ON
2. Select "HEIGT SEN" of AIR LEVELIZER data monitor test item.
HEIGHT SEN : 0.2V - 4.8V
Is the HEIGHT SEN voltage within the given range?
YES - Height sensor is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Height Sensor Signal Circuit/Diagnosis Procedure.
C1802
C1802 COMPRESSOR RELAY
Description
The compressor motor relay is controlled by the suspension control unit. The suspension control unit supplies voltage to the coil side of the relay
to activate it. The compressor motor relay, when activated, supplies power to the suspension air compressor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 105
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
C1803
C1803 EXHAUST SOLENOID
Description
The exhaust valve solenoid controls the vent function of the suspension control system. The exhaust valve solenoid is built into the suspension air
compressor. The suspension control unit supplies voltage to the exhaust valve solenoid to activate it.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK EXHAUST SOLENOID OPERATION
CAUTION:
While operating this active test, the suspension control system will vent air pressure and the vehicle ride height will lower. Ensure the
area around the vehicle is free from obstructions before beginning test.
CONSULT-III
1. Ensure the suspension control system has air pressure and is not drooping in the rear.
2. Select "EXHAUST SOLENOID" of AIR LEVELIZER active test items.
3. While operating test item, check that the exhaust valve solenoid opens to vent air from the system. The vehicle should lower when the exhaust
valve solenoid is activated.
Does the system vent properly?
YES - Exhaust valve solenoid is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Exhaust Valve Solenoid Circuit/Diagnosis Procedure.
C1804
C1804 HEIGHT ADJUSTING MALFUNCTION (COMPRESSOR)
Description
The compressor motor relay is controlled by the suspension control unit. The suspension control unit supplies voltage to the coil side of the relay
to activate it. The compressor motor relay, when activated, supplies power to the suspension air compressor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 106
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
C1805
C1805 HEIGHT ADJUSTING MALFUNCTION (EXH SOLENOID)
Description
The exhaust valve solenoid controls the vent function of the suspension control system. The exhaust valve solenoid is built into the suspension air
compressor. The suspension control unit supplies voltage to the exhaust valve solenoid to activate it.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK EXHAUST SOLENOID OPERATION
CAUTION:
While operating this active test, the suspension control system will vent air pressure and the vehicle ride height will lower. Ensure the
area around the vehicle is free from obstructions before beginning test.
CONSULT-III
1. Ensure the suspension control system has air pressure and is not drooping in the rear.
2. Select "EXHAUST SOLENOID" of AIR LEVELIZER active test items.
3. While operating test item, check that the exhaust valve solenoid opens to vent air from the system. The vehicle should lower when the exhaust
valve solenoid is activated.
Does the system vent properly?
YES - Exhaust valve solenoid is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Exhaust Valve Solenoid Circuit/Diagnosis Procedure.
C1806
C1806 VEHICLE HEIGHT SENSOR LOCKING MALFUNCTION
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK HEIGHT SENSOR OPERATION
CONSULT-III
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 107
1. Turn ignition switch ON
2. Select "HEIGT SEN" of AIR LEVELIZER data monitor test item.
HEIGHT SEN : 0.2V - 4.8V with no more than ±0.02V variation
Is the HEIGHT SEN voltage within the given range?
YES - Height sensor is operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Height Sensor Signal Circuit/Diagnosis Procedure.
C1807
C1807 SENSOR 5V MALFUNCTION
Description
The vehicle height sensor operates on a 5 volt reference signal from the suspension control unit. The suspension control unit also provides ground
to the height sensor.
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
Regarding Wiring Diagram information, See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic
)/Diagrams/Electrical Diagrams.
1.POWER SUPPLY CIRCUIT CHECK
1. Disconnect height sensor connector C8.
2. Turn the ignition switch ON.
3. Check voltage between the height sensor connector C8 terminal
1 and ground.
Is 5V present?
YES - System is working normally.
NO - Check harness or connector for open or short. If OK, replace the suspension control unit. See: Relays and Modules/Relays and Modules -
Steering and Suspension/Relays and Modules - Suspension/Suspension Control Module/Service and Repair/Removal and Replacement.
C1808
C1808 INTEGRAL TIME MALFUNCTION SUPPLYING AIR
Description
The suspension air compressor is supplied power by the compressor motor relay. The suspension control unit supplies power to the compressor
motor relay in order to activate the relay and subsequently activate the suspension air compressor.
DTC Logic
Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) C CODE Page 108
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK COMPRESSOR MOTOR RELAY OPERATION
CAUTION:
The "COMPRESSOR" active test will remain ON until it is turned off using CONSULT-III. Allowing the compressor to run for an
extended period of time may cause damage to the air levelizer system components due to excessive air pressure.
CONSULT-III
1. Turn ignition ON.
2. Select "COMPRESSOR" of AIR LEVELIZER active test items.
3. While operating test item, check that the suspension air compressor turns ON.
Does the suspension air compressor operate properly?
YES - Compressor motor relay and suspension air compressor are operating normally.
NO - See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic )/Testing and Inspection/Component Tests and
General Diagnostics/Compressor Motor Relay/Diagnosis Procedure.
