Skip to main content

Nissan Armada Technical Service Bulletin # NHTSA10V371000 Date: 100809

****************************
****************************

Nissan Armada Technical Service Bulletin # NHTSA10V371000 Date: 100809
Recall 10V371000: 2nd Row Seat Center Hinge/Latch
VEHICLE MAKE/MODEL: MODEL YEAR(S):
Nissan/Armada 2010
MANUFACTURER: Nissan North America, Inc.
MFR'S REPORT DATE: August 09, 2010
NHTSA CAMPAIGN ID NUMBER: 10V371000
NHTSA ACTION NUMBER: N/A
COMPONENT: Seats
POTENTIAL NUMBER OF UNITS AFFECTED: 174
Nissan Armada 2wd v8 5.6L Parts Service 334
SUMMARY:
Nissan is recalling certain model year 2010 Nissan Armada vehicles manufactured from June 7, 2010 through June 11, 2010. These vehicles fail to
comply with the requirements of Federal Motor Vehicle Safety Standard No. 207, "Seating Systems." The second row center seat hinge assembly
was manufactured out of specification. This may prevent the rear center seatback from fully locking in the in-use (upright) position.
CONSEQUENCE:
In the event of a crash, the second row center seat may not function properly increasing the risk of injury to the seat occupant.
REMEDY:
Dealers will inspect the second row center seat hinges/lock for proper function. If the seat does not lock as designed, the second row center seat
hinge assembly will be replaced with a new one free of charge. The safety recall is expected to begin on or before August 30, 2010. Owners may
contact Nissan at 1-800-647-7261.
NOTES:
Owners may also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153),
or go to http://www.safercar.gov.
Labels:
Location: 2350 15th Ave NW, Ruso, ND 58778, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...
Post a Comment
Read more