Skip to main content

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts Page 123

****************************
****************************

Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE) A L L Diagnostic Trouble Codes ( DTC ): B Code Charts  Page 123
- GO TO 2
2. STEP 2
Check "Self diagnostic result" with CONSULT-III.
Is the DTC detected?
YES - Perform diagnosis procedure. See: B2126.
NO - Inspection End.
Diagnosis Procedure
Regarding Wiring Diagram information, See: Accessories and Optional Equipment/Memory Positioning Systems/Diagrams/Electrical
Diagrams/Driver Seat Control Unit.
1. CHECK DTC
Check "Self diagnostic result" for BCM with CONSULT-III.
Are other DTCs detected?
YES - Check the DTC.
NO - GO TO 2
2. CHECK PARK POSITION SWITCH SIGNAL
1. Turn ignition switch ON.
2. Select "DETENT SW" in "Data Monitor" mode with CONSULT-III.
3. Check detention switch signal under the following condition.
Is the status normal?
YES - A/T shift selector (park position switch) circuit is OK.
NO - GO TO 3
3. CHECK A/T SHIFT SELECTOR (PARK POSITION SWITCH) HARNESS
1. Turn ignition switch OFF.
2. Disconnect A/T shift selector and driver seat control unit.
3. Check continuity between driver seat control unit connector
B202 (A) terminal 21 and A/T shift selector connector M203 (B) terminal 6
6 - 21 : Continuity should exist.
4. Check continuity between driver seat control unit connector
B202 (A) terminal 21 and ground.
21 - Ground : Continuity should not exist.
Is the inspection result normal?
YES - GO TO 4
NO - Repair or replace harness.
4. CHECK PARK POSITION SWITCH
Labels:
Location: 1250-1298 County Rd 150 N, Nokomis, IL 62075, USA

Comments

Post a Comment

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconnect
Post a Comment
Read more

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on.
Post a Comment
Read more

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr
Post a Comment
Read more