Skip to main content

Nissan Armada Technical Service Bulletin # 10-050 Date: 100326

****************************
****************************

Nissan Armada Technical Service Bulletin # 10-050 Date: 100326
Suspension - Front End Popping/Clunking Noises
Classification: FA10-001
Reference: NTB10-050
Date: March 26, 2010
Nissan Armada 2wd v8 5.6L Parts Service 267
2008-2010 ARMADA AND TITAN; POPPING OR CLUNKING NOISE FROM FRONT SUSPENSION
APPLIED VEHICLES2: 008-2010 Armada (TA60)
2008-2010 Titan (A60)
IF YOU CONFIRM
Using chassis ears, a popping or clunking noise can be heard coming from the front suspension shock assembly of an Applied Vehicle when driving
over a pot hole or speed bump at approximately 10MPH.
AND
The front suspension bolts are torqued to specification.
ACTIONS
1) Replace the front coil spring on both sides (RH & LH) with the part listed in the Parts Information section of this bulletin.
2) Check/set the front alignment.
3) Perform aiming adjustment for the headlamp and front fog lamp (if equipped).
IMPORTANT:
The purpose of "ACTIONS" (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire Service
Procedure as it contains information that is essential to successfully completing this repair.
PARTS INFORMATION
CLAIMS INFORMATION
SERVICE PROCEDURE
1. Replace the front coil spring on both sides (RH & LH) with the part listed in the Parts Information section of this bulletin.
^ Refer to the FSU section of the applicable Electronic Service Manual (ESM) for removal and installation instructions.
NOTE:
The front ride height will be around 1 inch lower after replacement.
2. Use an alignment rack to check/set the front alignment.
^ Refer to the FSU section of the applicable ESM for alignment instructions.
Nissan Armada 2wd v8 5.6L Parts Service 268
^ Make sure the alignment rack has been recently calibrated.
3. Perform aiming adjustment for the headlamp and front fog lamp (if equipped).
^ Refer to the EXL section of the applicable ESM for adjustment instructions.

Comments

Popular posts from this blog

C1140 C1140 ACTUATOR RLY

**************************** **************************** C1140 C1140 ACTUATOR RLY Description Activates or deactivates each solenoid valve according to the signals transmitted by the ABS actuator and electric unit (control unit). DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1140. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or replace terminal. Nissan-Datsun Truck Armada 2WD V8-5.6L (VK56DE)  C CODE Page 49 4. Reconn...

C1144 C1143, C1144 STEERING ANGLE SENSOR

**************************** **************************** C1144 C1143, C1144 STEERING ANGLE SENSOR Description The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAGNOSIS RESULTS Check the self-diagnosis results. Is above displayed on the self-diagnosis display? YES - Proceed to diagnosis procedure. See: C1143. NO - Inspection End Diagnosis Procedure Regarding Wiring Diagram information, See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams. 1.CONNECTOR INSPECTION 1. Turn ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) connector. 3. Disconnect steering angle sensor connector. 4. Check terminal for deformation, disconnection, looseness, and so on. ...

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021

2014 Nissan-Datsun Altima Diagrams. DTC # 10-126 Date: 101021 Steering/Suspension - Wheel Bearing Collision Damage Classification: FA10-006 Reference: NTB10-126 Date: October 21, 2010 WHEEL BEARING COLLISION DAMAGE APPLIED VEHICLES: All Nissan SERVICE INFORMATION Impacts to wheel bearings (such as a collision or other suspension damage) may create slight indents in the bearing surfaces. These indents may not 2019 Nissan-Datsun Altima L4-2.5L (QR25DE) Page 446 be visible but can cause bearing noise. NOTE: Hub/bearing replacement due to impact (collision or other suspension damage) is not a warrantable repair If a vehicle has visible wheel or suspension damage due to impact (collision or other suspension damage), it is recommended that the wheel bearing assembly be inspected as follows: 1. Remove the hub/bearing assembly from the vehicle. 2. Hold the hub/bearing assembly with both hands. 3. Rotate the hub/bearing assembly in both directions (clockwise and counterclockwise). 4. If any gr...